Why tap changer is kept at neutral end?

Why tap changer is kept at neutral end? 
by

1 Answer

Answer :

a) To reduce insulation cost of tap changer.

b) But reactance changeover the tap range increases. 
by

Related questions

Why our GT having off load tap changer?

Description : Why our GT having off load tap changer?

Last Answer : Because our station is base load station.  

Why there is no mixing of oil of tap changer and transformer?

Description : Why there is no mixing of oil of tap changer and transformer?

Last Answer : When the tap changing takes place arc is struck between the contacts. Due to this the oil inside the tap changer will be highly carbonised. If both oil get mixed up the quality of transformer tank oil will come down. This is not advisable. Hence both oils are kept separately. 

Why off load tap changer was chosen for GT?

Description : Why off load tap changer was chosen for GT?

Last Answer : Because our plant works on base load always.  

An electric bulb is connected on a holder. One end of the wire is connected to the phase and the remaining one connected to earth instead of neutral. The bulb will glow or not? If yes then what is the need of neutral?

Description : An electric bulb is connected on a holder. One end of the wire is connected to the phase and the remaining one connected to earth instead of neutral. The bulb will glow or not? If yes then what is the need of neutral?

Last Answer : 1. Yes the bulb will be glow & neutral is return path of Circuit it is originated from distribution transformers star point, form this point only neutral is taken. 2. Then what is the need ... : It gives assurance of reliable centralized earthling as your home may or may not have reliable earthling.

In recovery from a spin: a. Ailerons should be kept neutral b. Airspeed increases c. Ailerons used to stop the spin d. Rudder and ailerons used against the direction of spin direction

Description : In recovery from a spin: a. Ailerons should be kept neutral b. Airspeed increases c. Ailerons used to stop the spin d. Rudder and ailerons used against the direction of spin direction

Last Answer : a. Ailerons should be kept neutral

A long, hollow conducting cylinder is kept coaxially inside another long, hollow conducting cylinder of larger radius. Both the cylinders are initially electrically neutral.

Description : A long, hollow conducting cylinder is kept coaxially inside another long, hollow conducting cylinder of larger radius. Both the cylinders are initially electrically neutral. (A) A potential ... difference appears between the two cylinders when same charge density is given to both the cylinders

Last Answer : (A) A potential difference appears between the two cylinders when a charge density is given to the inner cylinder

Can I make a bluetooth printer using a USB gender changer and geting a cheap dongle?

Description : Can I make a bluetooth printer using a USB gender changer and geting a cheap dongle?

Last Answer : Seems like it would work in theory but then again communism works in theory… The main problem you would have is your PC not seeing the printer on the signal.

Are you an icon changer ?

Description : Are you an icon changer ?

Last Answer : Not so far as to change the dock but i do change my icons… The change from Tiger to Leopard left them looking slightly plain

I need a good voice changer?

Description : I need a good voice changer?

Last Answer : answer:Up to no good huh… Yes you must give us details.

In the CNC machine which device used to hold the workpiece? a.Automatic pallet changer b.Automatic work part positioner c.A & B both d.None of the above

Description : In the CNC machine which device used to hold the workpiece? a.Automatic pallet changer b.Automatic work part positioner c.A & B both d.None of the above

Last Answer : c.A & B both

What is the full form of ATC? a.Automatic tool changer b.Arranged tool changer c.Automatic tool controller d.Arranged tool controller

Description : What is the full form of ATC? a.Automatic tool changer b.Arranged tool changer c.Automatic tool controller d.Arranged tool controller

Last Answer : a.Automatic tool changer

The author of the book Game Changer ? -General Knowledge

Description : The author of the book Game Changer ? -General Knowledge

Last Answer : Shahid Afridi

how do i fix auto cd changer?

Description : how do i fix auto cd changer?

Last Answer : Need Answer

How to Load CDs Into a Car CD Changer?

Description : How to Load CDs Into a Car CD Changer?

Last Answer : If you have a multi-CD changer in your car, are you taking fulladvantage of it? Loading CDs into a car CD changer can seemcomplicated, but it doesn't have to be. If you follow these ... to be located somewhere else in thevehicle. Once you've identified where the CD changer is located,dete

Can I use a factory stereo with a aftermarket cd changer?

Description : Can I use a factory stereo with a aftermarket cd changer?

Last Answer : Yes, there are universal cd changers sold

Will the Pioneer CDX-FM687 6-Disc CD Changer work with any head unit?

Description : Will the Pioneer CDX-FM687 6-Disc CD Changer work with any head unit?

Last Answer : The Pioneer CDX-FM687 will work with any head unit, but works best with other Pioneer units.

Will my Kenwood KDC-C719 10-Disc CD Changer be able to play my burned cds?

Description : Will my Kenwood KDC-C719 10-Disc CD Changer be able to play my burned cds?

Last Answer : The Kenwood KDC-C719 is compatible with CD-R media.

Is the Kenwood KDC-C669 6-Disc CD Changer better overall in comparison to the Pioneer CDX-FM687 6-Disc CD Changer ?

Description : Is the Kenwood KDC-C669 6-Disc CD Changer better overall in comparison to the Pioneer CDX-FM687 6-Disc CD Changer ?

Last Answer : The Kenwood KDC-C669 gets slightly better reviews from users.Neither is really setting the world on fire with enthusiasm.

How do you prevent the CDs from getting stuck in a car CD changer?

Description : How do you prevent the CDs from getting stuck in a car CD changer?

Last Answer : You need to clean the CD Changer every 6 months to ensure the CD Changer runs smoothly.

how does a car cd changer work?

Description : how does a car cd changer work?

Last Answer : A car CD changer works by being placed in a trunk and mechanically rotating the discs to be read.

What are the advantages of a removeable face plate on my cd changer?

Description : What are the advantages of a removeable face plate on my cd changer?

Last Answer : A removable face plate helps to deter theft if removed upon exiting the car.

How many cd's does the typical cd changer hold?

Description : How many cd's does the typical cd changer hold?

Last Answer : Typical changers carry around 6 to 12 cds.

Does a car cd changer draw of lot of power from your battery?

Description : Does a car cd changer draw of lot of power from your battery?

Last Answer : That won't usually be a problem so long as you follow instructions and you don't have a lot of other things drawing power.

Where can I get voice changer software?

Description : Where can I get voice changer software?

Last Answer : You should try DynaSpy, they have a pretty good voice software program available.

An autotransformer is equipped with a 50% tap, a 65% tap, and an 80% tap. Which of the following statements is true concerning a load connected to the 50% tap? A. The load is receiving minimum voltage and minimum current. B. The load is receiving minimum voltage and maximum current. C. The load is receiving maximum voltage and minimum current. D. The load is receiving maximum voltage and maximum current.

Description : An autotransformer is equipped with a 50% tap, a 65% tap, and an 80% tap. Which of the following statements is true concerning a load connected to the 50% tap? A. The load is ... is receiving maximum voltage and minimum current. D. The load is receiving maximum voltage and maximum current.

Last Answer : Answer: B

Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it with a de-energized tag C. be equipped with an insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Description : Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it ... insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Last Answer : Answer: D

In a Tap changing transformer on which side is the tap connected, primary side or secondary side?

Description : In a Tap changing transformer on which side is the tap connected, primary side or secondary side?

Last Answer : A. Tapings are always connected to high voltage winding side, because of low current. If we connect tapings to low voltage side, sparks will produce while tap changing operation due to high current.

Why the tap changers are always connected to HV side of the transformer?

Description : Why the tap changers are always connected to HV side of the transformer? 

Last Answer : During tap changing action the load current has to be shifted from one tap to another tap. In case HV wining the load current will be less. Hence lesser arcing will take place. 

Determine the transformer tap ratios when the receiving end voltage is equal to the sending end voltage,...

Description : Determine the transformer tap ratios when the receiving end voltage is equal to the sending end voltage, the high voltage line operates at 220 kV and transmit 80 MW at 0.8 pf and the impedance of the line is (40+j140)ohm. Assume tstr=1.0  (A) 0.8 (B) 0.9 (C) 0.7 (D) 0.6 

Last Answer : 0.9 explanation given vs=vr convert in to phase voltage because impedence is always in phase line 220/root 3 then divided by reactive part that is 140 127.01/140=0.9 ans

In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Description : In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Last Answer : Answer: C

If an AC generator experiences voltage failure, the cause may be _____________. A. an open in the field circuit B. the brushes shifting out of the neutral plane C. excessive locked-rotor current D. a rotating slip ring

Description : If an AC generator experiences voltage failure, the cause may be _____________. A. an open in the field circuit B. the brushes shifting out of the neutral plane C. excessive locked-rotor current D. a rotating slip ring

Last Answer : Answer: A

Brushes in a generator must be positioned in the neutral plane to avoid sparking between the brushes and the _____________. A. yoke B. armature windings C. field pole windings D. commutator

Description : Brushes in a generator must be positioned in the neutral plane to avoid sparking between the brushes and the _____________. A. yoke B. armature windings C. field pole windings D. commutator

Last Answer : Answer: D

In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Description : In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Last Answer : Answer: B

As the ahead valve opens as shown in the illustration, pin #5 of the Sensor ______________. EL-0099 A. becomes more negative B. becomes more positive C. approaches neutral point D. approaches ground potential

Description : As the ahead valve opens as shown in the illustration, pin #5 of the Sensor ______________. EL-0099 A. becomes more negative B. becomes more positive C. approaches neutral point D. approaches ground potential

Last Answer : Answer: B

A bus disconnect link is used to isolate _____________. A. one bus bar from another B. the generator circuit breaker from the bus C. different phases from the equalizer connection D. positive and negative buses from the neutral

Description : A bus disconnect link is used to isolate _____________. A. one bus bar from another B. the generator circuit breaker from the bus C. different phases from the equalizer connection D. positive and negative buses from the neutral

Last Answer : Answer: B

The function of the commutator in a DC motor is to ________. A. reverse the flow of current through the armature B. reverse the flow of current in the field poles C. reduce the reluctance of the magnetic path through the motor D. shift the neutral running plane of the brushes to prevent sparking

Description : The function of the commutator in a DC motor is to ________. A. reverse the flow of current through the armature B. reverse the flow of current in the field poles C. reduce the reluctance of the magnetic path through the motor D. shift the neutral running plane of the brushes to prevent sparking

Last Answer : Answer: A

Prior to starting an AC generator prime mover, the voltage regulator cutout switch should be placed in the __________. A. manual position B. bus neutral position C. raise voltage position D. transfer position

Description : Prior to starting an AC generator prime mover, the voltage regulator cutout switch should be placed in the __________. A. manual position B. bus neutral position C. raise voltage position D. transfer position

Last Answer : Answer: A

If the steering stand selector switch is allowed to remain in the 'Non-Followup' mode after testing of the steering gear, the rudder will _____________. EL-0097 A. not respond to commands from the helm B. move in one direction only regardless of the movement of the helm C. not respond to output from the rotary actuator D. stop moving only when the helm is counter-rotated to put the pump at neutral stroke

Description : If the steering stand selector switch is allowed to remain in the 'Non-Followup' mode after testing of the steering gear, the rudder will _____________. EL-0097 A. not respond to commands from the ... actuator D. stop moving only when the helm is counter-rotated to put the pump at neutral stroke

Last Answer : Answer: A

The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. separate exciter in a series with the shunt field C. carbon pile regulator in series with the load D. balance coil diverting neutral current through the shunt field

Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field

Last Answer : Answer: A

What is the neutral point earthing and its advantages?

Description : What is the neutral point earthing and its advantages?

Last Answer : In substation all the neutrals of rotating machines, transformers, busbars and other equipment are connected to ground. Some of the advantages are: Earth fault protection is based on the method of ... , grounding of neutral helps to reduce the over-voltages which occur on the one healthy phases

Why we do 2 types of earthing on transformer i.e.: body earthing & neutral earthing, what is function. I am going to install a 5oo kva transformer & 380 kva DG set what should the earthing value?

Description : Why we do 2 types of earthing on transformer i.e.: body earthing & neutral earthing, what is function. I am going to install a 5oo kva transformer & 380 kva DG set what should the earthing value?

Last Answer : The two types of earthing are Familiar as Equipment earthing and system earthing. In Equipment earthing: body (non conducting part) of the equipment should be earthed to safeguard the human ... earthing will be further classified into directly earthed, Impedance earthing, resistive (NGRs) earthing.

Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Description : Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Last Answer : Link is provided at a Neutral common point in the circuit from which various connections are taken for the individual control circuit and so it is given in a link form to withstand high Amps. ... So if any malfunction happens the fuse connected in the particular control circuit alone will blow off.

Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Description : Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Last Answer : A:Link is provided at a Neutral common point in the circuit from which various connection are taken for the individual control circuit and so it is given in a link form to withstand high Amps ... .So if any malfunction happen the fuse connected in the particular control circuit alone will blow off.

Why neutral resistor is added between neutral and earth of an alternator?

Description : Why neutral resistor is added between neutral and earth of an alternator?

Last Answer : In order to limit the flow of current through neutral and earth a resistor is introduced between them.

Name any two methods of reducing short circuit current/ By providing neutral reactance.

Description : Name any two methods of reducing short circuit current/ By providing neutral reactance.

Last Answer : By introducing a large value of shunt reactance between buses.

Why neutral breaker used in DG neutral grounding?

Description : Why neutral breaker used in DG neutral grounding?

Last Answer : In case of high earth fault currents it is therefore normal practice to install a circuit breaker in the neutral of the generator in order to reduce the total fault clearance time. 

Why the neutral is earthed through earthing resistance in case of UT and SUT?

Description : Why the neutral is earthed through earthing resistance in case of UT and SUT? 

Last Answer : This is done to limit the earth fault current.