In truss analysis, the reactions can be found by using the equation . a.R=KQ+F b.R=KQ-F c.R=K+QF d.R=K-QF

In truss analysis, the reactions can be found by using the equation . a.R=KQ+F b.R=KQ-F c.R=K+QF d.R=K-QF
by

1 Answer

Answer :

b.R=KQ-F
by

Related questions

On gathering stiffness and loads, the system of equations is given by a.KQ=F b.KQ≠F c.K=QF d.K≠QF

Description : On gathering stiffness and loads, the system of equations is given by a.KQ=F b.KQ≠F c.K=QF d.K≠QF

Last Answer : a.KQ=F

For truss analysis, which type of elements is used? a.Triangle b.Parallelogram c.Rectangle d.Bar

Description : For truss analysis, which type of elements is used? a.Triangle b.Parallelogram c.Rectangle d.Bar

Last Answer : d.Bar

Example for one – Dimensional element is . a.triangular element b.brick element c.truss element d.axisymmetric element

Description : Example for one – Dimensional element is . a.triangular element b.brick element c.truss element d.axisymmetric element

Last Answer : c.truss element

The truss element can deform only in the a.vertical direction b.horizontal direction c.inclined direction d.axial direction

Description : The truss element can deform only in the a.vertical direction b.horizontal direction c.inclined direction d.axial direction

Last Answer : d.axial direction

The truss element can resist only a.surface force b.axial force c.point load d.none of the above

Description : The truss element can resist only a.surface force b.axial force c.point load d.none of the above

Last Answer : b.axial force

The inherent characteristic of an equal percentage valve relating flow rate 'q' with valve stem movement 'x' are described by the equation (A) dq/dx = K (B) dq/dx = K.q (C) dq/dx = K/q (D) dq/dx = Kq 2

Description : The inherent characteristic of an equal percentage valve relating flow rate 'q' with valve stem movement 'x' are described by the equation (A) dq/dx = K (B) dq/dx = K.q (C) dq/dx = K/q (D) dq/dx = Kq 2

Last Answer : (A) dq/dx = K

The two-dimensional rotation equation in the matrix form is a.P’=T+P b.P’=S*P c.P’=R*P d.P’=dx+dy

Description : The two-dimensional rotation equation in the matrix form is a.P’=T+P b.P’=S*P c.P’=R*P d.P’=dx+dy

Last Answer : c.P’=R*P

The following is basically a material flow simplification technique a.A simple and visual method of cell design b.Family formation by classification and codification c.Cell formation using Production Flow Analysis d.All of the above

Description : The following is basically a material flow simplification technique a.A simple and visual method of cell design b.Family formation by classification and codification c.Cell formation using Production Flow Analysis d.All of the above

Last Answer : c.Cell formation using Production Flow Analysis

Which of the following technique of grouping does not consider the design and shape aspect? a.A simple and visual method of cell design b.Family formation by classification and codification c.Cell formation using Production Flow Analysis d.All of the above

Description : Which of the following technique of grouping does not consider the design and shape aspect? a.A simple and visual method of cell design b.Family formation by classification and codification c.Cell formation using Production Flow Analysis d.All of the above

Last Answer : c.Cell formation using Production Flow Analysis

In cell formation using production flow analysis, the following process will be left out of theanalysis a.Grinding b.Milling c.Drilling d.Gear cutting

Description : In cell formation using production flow analysis, the following process will be left out of theanalysis a.Grinding b.Milling c.Drilling d.Gear cutting

Last Answer : d.Gear cutting

The objects transformed using the equation P’=S*P should be a.Scaled b.Repositioned c.Both a and b d.Neither a nor b

Description : The objects transformed using the equation P’=S*P should be a.Scaled b.Repositioned c.Both a and b d.Neither a nor b

Last Answer : c.Both a and b

Choose the right sequence for Production Flow Analysis a.PFA Chart - Data Collection - Sortation of process plans b.Data collection - PFA chart - Sortation of process plans c.Sortation of process plans - Data collection - PFA chart d.Data collection - Sortation of process plans - PFA chart

Description : Choose the right sequence for Production Flow Analysis a.PFA Chart - Data Collection - Sortation of process plans b.Data collection - PFA chart - Sortation of process plans c.Sortation of process plans - Data collection - PFA chart d.Data collection - Sortation of process plans - PFA chart

Last Answer : d.Data collection - Sortation of process plans - PFA chart

Which of the following is not the method of part family formation a.Visual inspection method b.Automatic product sorting c.Parts classification & coding d.Production flow analysis

Description : Which of the following is not the method of part family formation a.Visual inspection method b.Automatic product sorting c.Parts classification & coding d.Production flow analysis

Last Answer : b.Automatic product sorting

For thermal analysis, the field variable is a.stress b.strain c.displacement d.Temperature

Description : For thermal analysis, the field variable is a.stress b.strain c.displacement d.Temperature

Last Answer : d.Temperature

Which of the following module of FEA is used to determine natural frequency? a.Static analysis b.Thermal analysis c.Modal analysis d.All of the above

Description : Which of the following module of FEA is used to determine natural frequency? a.Static analysis b.Thermal analysis c.Modal analysis d.All of the above

Last Answer : c.Modal analysis

Finite element analysis deals with . a.approximate numerical solution b.non-boundary value problems c.Laplace equations d.All of the above

Description : Finite element analysis deals with . a.approximate numerical solution b.non-boundary value problems c.Laplace equations d.All of the above

Last Answer : a.approximate numerical solution

What is the full form of FEA a.Fracture Element Analysis b.Finite Element Analysis c.Future Electronic Analysis d.None of the above

Description : What is the full form of FEA a.Fracture Element Analysis b.Finite Element Analysis c.Future Electronic Analysis d.None of the above

Last Answer : b.Finite Element Analysis

In the following geometric modelling techniques. which cannot be used for finiteelement analysis: a.Wireframe modelling b.Surface modelling c.Solid modeling d.none of the above

Description : In the following geometric modelling techniques. which cannot be used for finiteelement analysis: a.Wireframe modelling b.Surface modelling c.Solid modeling d.none of the above

Last Answer : d.none of the above

Incremental dimension in circular interpolation in X-axis is denoted by a.J b.I c.K d.None of the above

Description : Incremental dimension in circular interpolation in X-axis is denoted by a.J b.I c.K d.None of the above

Last Answer : b.I

In a CNC program block, N05 GO1 G91 G33 X20 Z-40 K5……, K refer to a.Depth of cut b.Pitch c.Multiple Threading Cycle d.Feed

Description : In a CNC program block, N05 GO1 G91 G33 X20 Z-40 K5……, K refer to a.Depth of cut b.Pitch c.Multiple Threading Cycle d.Feed

Last Answer : b.Pitch

Which of the following is true for the stiffness matrix (K)? a.K is a banded matrix b.K is un-symmetric c.K is an un-banded matrix d.none of the above

Description : Which of the following is true for the stiffness matrix (K)? a.K is a banded matrix b.K is un-symmetric c.K is an un-banded matrix d.none of the above

Last Answer : a.K is a banded matrix

For Q 45, Tangent vector for line L2 a.i+4j-k b.2i+4j+k c.i-4j-2k d.i+4j+2k

Description : For Q 45, Tangent vector for line L2 a.i+4j-k b.2i+4j+k c.i-4j-2k d.i+4j+2k

Last Answer : d.i+4j+2k

To determine the coefficients of the equation – two end-points and the two tangentvectors. This statement is true for which of the following? a.B-spline curve b.Hermite Cubic Spline Curve c.Beizer curve d.none of the above

Description : To determine the coefficients of the equation – two end-points and the two tangentvectors. This statement is true for which of the following? a.B-spline curve b.Hermite Cubic Spline Curve c.Beizer curve d.none of the above

Last Answer : b.Hermite Cubic Spline Curve

Find parametric equation for Y-coordinates of Hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.2u3-3u2+2u+4 b.3u3-2u2-2u-4 c.2u3-3u2-2u-4 d.2u3+3u2+2u+4

Description : Find parametric equation for Y-coordinates of Hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.2u3-3u2+2u+4 b.3u3-2u2-2u-4 c.2u3-3u2-2u-4 d.2u3+3u2+2u+4

Last Answer : a.2u3-3u2+2u+4

Find parametric equation for X-coordinates of hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.-5u3+8u2+u+1 b.5u3+8u2+u+1 c.8u3-5u2-u+1 d.8u3+5u2+u+1

Description : Find parametric equation for X-coordinates of hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.-5u3+8u2+u+1 b.5u3+8u2+u+1 c.8u3-5u2-u+1 d.8u3+5u2+u+1

Last Answer : a.-5u3+8u2+u+1

Parametric equation for circle a.X=x+Rcosu; Y=y+Rsinu; Z=z b.X=Rcosu; Y=Rsinu; Z=z c.X=x+Rsinu; Y=y+Rcosu; Z=z d.X=Rsinu; Y=y+Rcosu; Z=z

Description : Parametric equation for circle a.X=x+Rcosu; Y=y+Rsinu; Z=z b.X=Rcosu; Y=Rsinu; Z=z c.X=x+Rsinu; Y=y+Rcosu; Z=z d.X=Rsinu; Y=y+Rcosu; Z=z

Last Answer : a.X=x+Rcosu; Y=y+Rsinu; Z=z

Write parametric equation of line having end points P1(3,5,8) and P2 (6,4,3). a.[3 5 8]+u[3 -1 -5] b.[3 5 8]+u[3 1 5] c.[3 8 5]+u[3 -1 -5] d.[3 5 8]+u[-3 1 5]

Description : Write parametric equation of line having end points P1(3,5,8) and P2 (6,4,3). a.[3 5 8]+u[3 -1 -5] b.[3 5 8]+u[3 1 5] c.[3 8 5]+u[3 -1 -5] d.[3 5 8]+u[-3 1 5]

Last Answer : a.[3 5 8]+u[3 -1 -5]

To determine the coefficients of the equation – two end-points and the two tangentvectors. This statement is true for which of the following a.B-spline curve b.Hermite Cubic Spline Curve c.Beizer curve d.none of the above

Description : To determine the coefficients of the equation – two end-points and the two tangentvectors. This statement is true for which of the following a.B-spline curve b.Hermite Cubic Spline Curve c.Beizer curve d.none of the above

Last Answer : b.Hermite Cubic Spline Curve

A straight line segment is translated by applying the transformation equation a.P’=P+T b.Dx and Dy c.P’=P+P d.Only c

Description : A straight line segment is translated by applying the transformation equation a.P’=P+T b.Dx and Dy c.P’=P+P d.Only c

Last Answer : a.P’=P+T

The two-dimensional translation equation in the matrix form is a.P’=P+T b.P’=P-T c.P’=P*T d.P’=P

Description : The two-dimensional translation equation in the matrix form is a.P’=P+T b.P’=P-T c.P’=P*T d.P’=P

Last Answer : a.P’=P+T

In 2D-translation, a point (x, y) can move to the new position (x’, y’) by usingthe equation a.x’=x+dx and y’=y+dx b.x’=x+dx and y’=y+dy c.X’=x+dy and Y’=y+dx d.X’=x-dx and y’=y-dy

Description : In 2D-translation, a point (x, y) can move to the new position (x’, y’) by usingthe equation a.x’=x+dx and y’=y+dx b.x’=x+dx and y’=y+dy c.X’=x+dy and Y’=y+dx d.X’=x-dx and y’=y-dy

Last Answer : b.x’=x+dx and y’=y+dy

Match the following: NC code DefinitionP. M05 1. Absolute coordinate system Q. G01 2. Dwell R. G04 3. Spindle stop S. G09 4. Linear interpolation a.P-2, Q-3, R-4, S-1 b.P-3, Q-4, R-1, S-2 c.P-3, Q-4, R-2, S-1 d.P-4, Q-3, R-2, S-1

Description : Match the following: NC code DefinitionP. M05 1. Absolute coordinate system Q. G01 2. Dwell R. G04 3. Spindle stop S. G09 4. Linear interpolation a.P-2, Q-3, R-4, S-1 b.P-3, Q-4, R-1, S-2 c.P-3, Q-4, R-2, S-1 d.P-4, Q-3, R-2, S-1

Last Answer : c.P-3, Q-4, R-2, S-1

Coordinate of â–¡ABCD is WCS are: lowermost corner A(2,2) & diagonal corner are C(8,6). W.r.t MCS. The coordinates of origin of WCS system are (5,4). If the axes of WCS are at 600 in CCW w.r.t. the axes of MCS. Find new vertices of point A in MCS. a.(4.268, 6.732) b.(5.268, 6.732) c.(4.268, 4.732) d.(6.268, 4.732)

Description : Coordinate of â- ABCD is WCS are: lowermost corner A(2,2) & diagonal corner are C(8,6). W.r.t MCS. The coordinates of origin of WCS system are (5,4). If the axes of WCS are at 600 in CCW w.r.t. the axes of MCS. Find new ... in MCS. a.(4.268, 6.732) b.(5.268, 6.732) c.(4.268, 4.732) d.(6.268, 4.732)

Last Answer : a.(4.268, 6.732)

General pivot point rotation can be expressed as a.T(zr,yr).R(θ).T(-zr,-yr) = R(xr,yr,θ) b.T(xr,yr).R(θ).T(-xr,-yr) = R(xr,yr,θ) c.T(xr,yr).R(θ).T(-xr,-yr) = R(zr,yr,θ) d.T(xr,yr).R(θ).T(-xr,-yr) = R(zr,yr,θ)

Description : General pivot point rotation can be expressed as a.T(zr,yr).R(θ).T(-zr,-yr) = R(xr,yr,θ) b.T(xr,yr).R(θ).T(-xr,-yr) = R(xr,yr,θ) c.T(xr,yr).R(θ).T(-xr,-yr) = R(zr,yr,θ) d.T(xr,yr).R(θ).T(-xr,-yr) = R(zr,yr,θ)

Last Answer : b.T(xr,yr).R(θ).T(-xr,-yr) = R(xr,yr,θ)

Rotation is simply---------object w.r.t origin or centre point. a.Turn b.Shift c.Compression d.Drag element

Description : Rotation is simply---------object w.r.t origin or centre point. a.Turn b.Shift c.Compression d.Drag element

Last Answer : a.Turn

The original coordinates of the point in polar coordinates are a.X’=r cos (Ф +ϴ) and Y’=r cos (Ф +ϴ) b.X’=r cos (Ф +ϴ) and Y’=r sin (Ф +ϴ) c.X’=r cos (Ф -ϴ) and Y’=r cos (Ф -ϴ) d.X’=r cos (Ф +ϴ) and Y’=r sin (Ф -ϴ)

Description : The original coordinates of the point in polar coordinates are a.X’=r cos (Ф +ϴ) and Y’=r cos (Ф +ϴ) b.X’=r cos (Ф +ϴ) and Y’=r sin (Ф +ϴ) c.X’=r cos (Ф -ϴ) and Y’=r cos (Ф -ϴ) d.X’=r cos (Ф +ϴ) and Y’=r sin (Ф -ϴ)

Last Answer : b.X’=r cos (Ф +ϴ) and Y’=r sin (Ф +ϴ)

The matrix representation for scaling in homogeneous coordinates is a.P’=S*P b.P’=R*P c.P’=dx+dy d.P’=S*S

Description : The matrix representation for scaling in homogeneous coordinates is a.P’=S*P b.P’=R*P c.P’=dx+dy d.P’=S*S

Last Answer : a.P’=S*P

Which of the process is using the extrusion concept? a.SLA b.SLS c.FDM d.MJM

Description : Which of the process is using the extrusion concept? a.SLA b.SLS c.FDM d.MJM

Last Answer : c.FDM

Which one of the processes is NOT using a laser? a.FDM b.SLA c.SLS d.LOM

Description : Which one of the processes is NOT using a laser? a.FDM b.SLA c.SLS d.LOM

Last Answer : a.FDM

The points in the entire structure are defined using the coordinates system is known as a.local coordinates system b.natural coordinates system c.global coordinate system d.none of the above

Description : The points in the entire structure are defined using the coordinates system is known as a.local coordinates system b.natural coordinates system c.global coordinate system d.none of the above

Last Answer : c.global coordinate system

A cylinder can be created by drawing a rectangular shape using the ________ tool. a.revolve b.sweep c.extrude d.all of the above

Description : A cylinder can be created by drawing a rectangular shape using the ________ tool. a.revolve b.sweep c.extrude d.all of the above

Last Answer : a.revolve

The ___________ is used to create a surface using curves that form closed boundaries a.ruled Surface b.plane Surface c.coons patch d.surface of Revolution

Description : The ___________ is used to create a surface using curves that form closed boundaries a.ruled Surface b.plane Surface c.coons patch d.surface of Revolution

Last Answer : c.coons patch

The is used to create a surface using curves that form closed boundaries. a.ruled Surface b.plane Surface c.coons patch d.surface of Revolution

Description : The is used to create a surface using curves that form closed boundaries. a.ruled Surface b.plane Surface c.coons patch d.surface of Revolution

Last Answer : c.coons patch

Arrhenius equation K = Ae-E a / R T In some reactions, Rate of reaction is directly proportional to. Concentration of catalyst Catalyst used in Bio-Chemical reactions is called. Enzymes Reactions catalyzed by light are called as. Photo catalyzed or Photosensitised reactions

Description : Arrhenius equation K = Ae-E a / R T In some reactions, Rate of reaction is directly proportional to. Concentration of catalyst Catalyst used in Bio-Chemical reactions is called. Enzymes Reactions catalyzed by light are called as. Photo catalyzed or Photosensitised reactions

Last Answer : Define order of reaction

Which one of the following statements is TRUE? a.Teach pendant is used for lead-through teaching. b.Teach pendant is used for manual teaching. c.Teach pendant is used for off-line teaching of robots. d.Teach pendant is not used in robot teaching.

Description : Which one of the following statements is TRUE? a.Teach pendant is used for lead-through teaching. b.Teach pendant is used for manual teaching. c.Teach pendant is used for off-line teaching of robots. d.Teach pendant is not used in robot teaching.

Last Answer : b.Teach pendant is used for manual teaching.

A company is producing 15000 mobiles annually. Determine production scale of company a.Low Production b.Medium Production c.High Production d.None

Description : A company is producing 15000 mobiles annually. Determine production scale of company a.Low Production b.Medium Production c.High Production d.None

Last Answer : c.High Production

--------is a manufacturing system in which sequence of operation is fixed by equipmentconfiguration a.Flexible b.Programmable c.Fixed d.All of above

Description : --------is a manufacturing system in which sequence of operation is fixed by equipmentconfiguration a.Flexible b.Programmable c.Fixed d.All of above

Last Answer : c.Fixed

Which manufacturing system is best suited for batch production a.Flexible b.Programmable c.Fixed d.All of above

Description : Which manufacturing system is best suited for batch production a.Flexible b.Programmable c.Fixed d.All of above

Last Answer : b.Programmable

Which automation is suited for high production quantities a.Flexible b.Programmable c.Fixed d.All of above

Description : Which automation is suited for high production quantities a.Flexible b.Programmable c.Fixed d.All of above

Last Answer : c.Fixed

A use computer to automatically generate process plans is? a.Lower-level strategies b.Intermediate strategies c.Higher-level strategies d.Morden-level strategies

Description : A use computer to automatically generate process plans is? a.Lower-level strategies b.Intermediate strategies c.Higher-level strategies d.Morden-level strategies

Last Answer : c.Higher-level strategies