nging the speed of feed mechanism (b) The number of knives on feed mechanism (c) Changing speed of cutter head (d) All of the above

nging the speed of feed mechanism
(b) The number of knives on feed mechanism
(c) Changing speed of cutter head
(d) All of the above
by

1 Answer

Answer :

(d) All of the above
by

Related questions

Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Description : Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Last Answer : (d) All of the above

Speed of band operated machines chaff cutter having two knives F. 35 rpm G. 50 rpm H. 600 rpm I. 1000 rpm

Description : Speed of band operated machines chaff cutter having two knives F. 35 rpm G. 50 rpm H. 600 rpm I. 1000 rpm

Last Answer : F. 35 rpm

knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Last Answer : a)Increase the co-efficient of friction between crop stalk machine

.The number of knives on powered chaff cutter a) 2-6 b) 1-2 c) 5-10 d) 10-20

Description : .The number of knives on powered chaff cutter a) 2-6 b) 1-2 c) 5-10 d) 10-20

Last Answer : a) 2-6

Speed of power operated machine chaff cutter is E. 35 rpm F. 50 rpm G. 600-1000 rpm H. None of the above

Description : Speed of power operated machine chaff cutter is E. 35 rpm F. 50 rpm G. 600-1000 rpm H. None of the above

Last Answer : G. 600-1000 rpm

Cutting speed of the impact type cutter is a)10-20 m/s. b)20-40m/s c)40-50m/s. d)46-56m/s

Description : Cutting speed of the impact type cutter is a)10-20 m/s. b)20-40m/s c)40-50m/s. d)46-56m/s

Last Answer : b)20-40m/s

Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Description : Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Last Answer : a)400-550 rpm

The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Description : The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Last Answer : 35

Capacity of field choppers (chaff cutter) is affected by (a)capacity of the feed mechanism (cross sectional area) (b)Rate of advance of material through throat considered as to be the same linear speed of feed mechanism (c) density of forage material (d) all of the above

Description : Capacity of field choppers (chaff cutter) is affected by (a)capacity of the feed mechanism (cross sectional area) (b)Rate of advance of material through throat considered as to be the same linear speed of feed mechanism (c) density of forage material (d) all of the above

Last Answer : (d) all of the above

The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Last Answer : D. Between the two lower Links

eripheral velocity of impact cutter is about: A.50m/sec B.20m/sec C.10m/sec D.5m/sec

Description : eripheral velocity of impact cutter is about: A.50m/sec B.20m/sec C.10m/sec D.5m/sec

Last Answer : A.50m/sec

The cutter bar of a tractor operated mower ordinarily makes: A. 800-1200 strokes/min B. 1600-2000 strokes/min C. 2400-2800 strokes/min D. 3200-3600 strokes/min

Description : The cutter bar of a tractor operated mower ordinarily makes: A. 800-1200 strokes/min B. 1600-2000 strokes/min C. 2400-2800 strokes/min D. 3200-3600 strokes/min

Last Answer : A. 800-1200 strokes/min

o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m

Description : o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m

Last Answer : b) 2.0cm/m

enght of cutter bar for the tractor operated mower or vertical conveyor reaper is..... (a) 1.5-3.0m (b) 3.0-4.5m (c)4.5-5.5m (d) >5.5m

Description : enght of cutter bar for the tractor operated mower or vertical conveyor reaper is..... (a) 1.5-3.0m (b) 3.0-4.5m (c)4.5-5.5m (d) >5.5m

Last Answer : (a) 1.5-3.0m

Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.

Description : Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.

Last Answer : Breaking of knives.

267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Description : 267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Last Answer : d)All of the above

Gears are used for: a)changing the speed rotation b)changing direction of rotation c)changing direction of shafting d)all of the above

Description : Gears are used for: a)changing the speed rotation b)changing direction of rotation c)changing direction of shafting d)all of the above

Last Answer : d)all of the above

Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Last Answer : a.) Decreasing cylinder peripheral speed.

For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Description : For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Last Answer : D)all of these

Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Last Answer : a) Higher cylinder speed.

Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Last Answer : a)peripheral speed of the drum

Seed drills differ from the planters in respect of a) metering mechanism b) ground wheel design c) transmission system between ground wheel and roller wheel d) none of the above

Description : Seed drills differ from the planters in respect of a) metering mechanism b) ground wheel design c) transmission system between ground wheel and roller wheel d) none of the above

Last Answer : a) metering mechanism

Planters differ from a seed drill in respect of- (A) kind of power transmission system (B)kind of metering mechanism (C)kind of furrow opener used (D)all of the above

Description : Planters differ from a seed drill in respect of- (A) kind of power transmission system (B)kind of metering mechanism (C)kind of furrow opener used (D)all of the above

Last Answer : (B)kind of metering mechanism

Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism

Description : Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism

Last Answer : (d) Inclined plate metering mechanism

The metering mechanism which is suitable for the metering of small seeds as well as large grains. (a) Internal double run mechanism (b) Fluted wheel mechanism (c) Stationary opening with auger (d) None of the above

Description : The metering mechanism which is suitable for the metering of small seeds as well as large grains. (a) Internal double run mechanism (b) Fluted wheel mechanism (c) Stationary opening with auger (d) None of the above

Last Answer : (a) Internal double run mechanism

The metering mechanism which is most suitable for metering of small seed is to handle is a. Internal double run mechanism b. Fluted wheel mechanism c. Stationery opening with agitator d. None of the above

Description : The metering mechanism which is most suitable for metering of small seed is to handle is a. Internal double run mechanism b. Fluted wheel mechanism c. Stationery opening with agitator d. None of the above

Last Answer : b. Fluted wheel mechanism

Most commonly used for the metering mechanism for fertilizer a. Spur wheel b. Serrated wheel c. Star wheel d. Auger type

Description : Most commonly used for the metering mechanism for fertilizer a. Spur wheel b. Serrated wheel c. Star wheel d. Auger type

Last Answer : a. Spur wheel

Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Description : Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Last Answer : A)ldler pulley

A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Description : A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Last Answer : a. Seed is increase

Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Description : Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Last Answer : (a) Cylinder losses

Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Last Answer : a) Cylinder losses

.When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Last Answer : B. L-head

An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Last Answer : d) None of the above

An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of operation is 2.0kmph, the area covered (ha), in 8-11day is given by: A. 1.85/1000k B. 28.8 x 10-2k C. k/6.56 D. 1.762k

Description : An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of operation is 2.0kmph, the area covered (ha), in 8-11day is given by: A. 1.85/1000k B. 28.8 x 10-2k C. k/6.56 D. 1.762k

Last Answer : B. 28.8 x 10-2k

Application rate of sprayer is affected by a. forward of speed b. number of nozzle c. rate of discharge d. all of the above

Description : Application rate of sprayer is affected by a. forward of speed b. number of nozzle c. rate of discharge d. all of the above

Last Answer : d. all of the above

An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of the operation is 2.0kmph then the area covered (ha), in 8 hr day is given by: a) 1.85/1000k b) 28.8 * 10-2k c) k/6.456 d) 1.762k

Description : An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of the operation is 2.0kmph then the area covered (ha), in 8 hr day is given by: a) 1.85/1000k b) 28.8 * 10-2k c) k/6.456 d) 1.762k

Last Answer : b) 28.8 * 10-2k

Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Description : Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : a) 300-400rpm

Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : d) 1100-1200rpm

Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Last Answer : c) 600-800rpm

main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops more current. C. To prevent building up of high voltage in a circuit. D. None of the above

Description : main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops ... . C. To prevent building up of high voltage in a circuit. D. None of the above

Last Answer : B. To safeguard against flow of high currents to battery when armature develops more current.

Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at high speed. C. To permit the generation to deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Description : Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at ... deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Last Answer : A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces.

Optimum operating speed of rotavator is a)20-150rpm b)150-350rpm c)350-500rpm d) >500rpm

Description : Optimum operating speed of rotavator is a)20-150rpm b)150-350rpm c)350-500rpm d) >500rpm

Last Answer : d) >500rpm

Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Description : Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Last Answer : c. Both (a) and (b)

Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Description : Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Last Answer : (B) Maximum brake horse power output

V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Description : V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Last Answer : c. both (a) and (b)

Slip of belt is responsible for A. Reduction is speed B. Reduction in power C. Reduction in belt life D. All of the above

Description : Slip of belt is responsible for A. Reduction is speed B. Reduction in power C. Reduction in belt life D. All of the above

Last Answer : D. All of the above

Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Description : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Last Answer : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Description : Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Last Answer : B. CI=[E/(N+E) ]×100