Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Most important factor affecting threshing efficiency
a)peripheral speed of the drum
b)cylinder concave clearance
c)moisture content of crop
d)feed rate
by

1 Answer

Answer :

a)peripheral speed of the drum
by

Related questions

The threshing efficiency of thresher depends on a) Cylinder peripheral speed b) Cylinder concave clearance c) Feed rate, moisture content and type of crop d) All are correct

Description : The threshing efficiency of thresher depends on a) Cylinder peripheral speed b) Cylinder concave clearance c) Feed rate, moisture content and type of crop d) All are correct

Last Answer :  All are correct

Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Last Answer : a) Higher cylinder speed.

Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Last Answer : M. Cylinder peripheral speed

A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660

Description : A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660

Last Answer : a. 11

Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Last Answer : (a) Increase threshing efficiency

Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Description : Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Last Answer : d) All of the above

Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Last Answer : a.) Decreasing cylinder peripheral speed.

Crop factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder types c) Cylinder speed, feed rate d) Cylinder type, feed rate

Description : Crop factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder types c) Cylinder speed, feed rate d) Cylinder type, feed rate

Last Answer : Variety of crop, Moisture in crop material

Operational factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate

Description : Operational factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate

Last Answer : Cylinder speed, feed rate

Machine factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate

Description : Machine factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate

Last Answer : Feeding chute angle, cylinder type

Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : d) 1100-1200rpm

The takes place between the cylinder and concave units of the combine. a) Threshing b) Feeding drum c) Straw spreader d) Separating

Description : The takes place between the cylinder and concave units of the combine. a) Threshing b) Feeding drum c) Straw spreader d) Separating

Last Answer : Threshing 

Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Description : Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Last Answer : (a) Angular velocity of straw Walker to angular velocity of threshing drum

.total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Description : Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Last Answer : F. Capacity of chaff cutters

A reaper used for : a. Cutting crop b. Cutting and windrewing c. Cutting and threshing d. None of these

Description : A reaper used for : a. Cutting crop b. Cutting and windrewing c. Cutting and threshing d. None of these

Last Answer : b. Cutting and windrewing

A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Description : A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Last Answer : a. Seed is increase

iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Last Answer : ∙ Torque is a function of thermal efficiency

Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Description : Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Last Answer : (a) Cylinder losses

Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Last Answer : a) Cylinder losses

In a thresher, by increasing the speed of threshing cylinder a) Threshing efficiency can be increased b) Broken grain loss can be minimized c) Un-threshed grains can be increased d) Straw breakup can be increased Ans. a

Description : In a thresher, by increasing the speed of threshing cylinder a) Threshing efficiency can be increased b) Broken grain loss can be minimized c) Un-threshed grains can be increased d) Straw breakup can be increased Ans. a

Last Answer : ans a

Different parts of Thresher are A) Feeding device B) Threshing cylinder C) Concave D) All of the above.

Description : Different parts of Thresher are A) Feeding device B) Threshing cylinder C) Concave D) All of the above.

Last Answer : All of the above.

Reaper is used for a.) Plowing b.) Harvesting and threshing. c.) Cutting crops. d.) Cutting and windrow.

Description : Reaper is used for a.) Plowing b.) Harvesting and threshing. c.) Cutting crops. d.) Cutting and windrow.

Last Answer : d.) Cutting and windrow.

Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec

Description : Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec

Last Answer : B. 18-20m/sec

The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance between the speed pick up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Description : Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Description : The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Last Answer : (c)reel speed index

The ideal moisture content for the soil primary tillage operation a) Upper plastic limit of the soil b) Lower plastic limit c) Wilting Point d) All of the above

Description : The ideal moisture content for the soil primary tillage operation a) Upper plastic limit of the soil b) Lower plastic limit c) Wilting Point d) All of the above

Last Answer : a) Upper plastic limit of the soil

Flat planting predominates where a) Nature moisture content is favourable b) Rainfall is high to provide surface drainage c) Semi arid areas to conserve moisture d) None of the above

Description : Flat planting predominates where a) Nature moisture content is favourable b) Rainfall is high to provide surface drainage c) Semi arid areas to conserve moisture d) None of the above

Last Answer : a) Nature moisture content is favourable

Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Description : Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Last Answer : (d) All of the above

Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Last Answer : c) 600-800rpm

One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle

Description : One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle

Last Answer : . Requires less pedal force to stop the vehicle

For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Description : For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Last Answer : D)all of these

nging the speed of feed mechanism (b) The number of knives on feed mechanism (c) Changing speed of cutter head (d) All of the above

Description : nging the speed of feed mechanism (b) The number of knives on feed mechanism (c) Changing speed of cutter head (d) All of the above

Last Answer : (d) All of the above

The mechanical cleaning of sugar cane is done due to A. The different in the peripheral velocity of rollers B. Rough surface provided Or the outer surface of rollers C. Blow of air which forces the extraneous material out of the machine D. All of the above

Description : The mechanical cleaning of sugar cane is done due to A. The different in the peripheral velocity of rollers B. Rough surface provided Or the outer surface of rollers C. Blow of air which forces the extraneous material out of the machine D. All of the above

Last Answer : D. All of the above

_______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape

Description : _______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape

Last Answer : c) Edge shape

Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Description : Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Last Answer : (B) Maximum brake horse power output

knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Last Answer : a)Increase the co-efficient of friction between crop stalk machine

Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front

Description : Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front

Last Answer : a) Concave

Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front

Description : Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front

Last Answer : a) Concave

Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Description : Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Last Answer : c) concave, convex

Which of the following is not a factor affecting Soil Water Availability? a) A Soil Texture b) B Nature of crop grown c) C Organic Matter d) D Salt content E Soil depth

Description : Which of the following is not a factor affecting Soil Water Availability? a) A Soil Texture b) B Nature of crop grown c) C Organic Matter d) D Salt content E Soil depth

Last Answer : b) B Nature of crop grown

.When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Last Answer : B. L-head

An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Last Answer : d) None of the above

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Last Answer : c) Spike tooth and hammer mill

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Last Answer : (b) Spike tooth cylinder

Compression pressure in petrol engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) 35-40 kg/cm2

Description : Compression pressure in petrol engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) 35-40 kg/cm2

Last Answer : a) 6-10 kg/cm2