Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Thresher blows broken grains with chaff due to  
a) Higher cylinder speed.
b) More feed Rate
c) More cylinder concave clearance
d) Moisture content of the crop is more
by

1 Answer

Answer :

a) Higher cylinder speed.
by

Related questions

Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Last Answer : a.) Decreasing cylinder peripheral speed.

Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Last Answer : a)peripheral speed of the drum

The threshing efficiency of thresher depends on a) Cylinder peripheral speed b) Cylinder concave clearance c) Feed rate, moisture content and type of crop d) All are correct

Description : The threshing efficiency of thresher depends on a) Cylinder peripheral speed b) Cylinder concave clearance c) Feed rate, moisture content and type of crop d) All are correct

Last Answer :  All are correct

Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Last Answer : M. Cylinder peripheral speed

Crop factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder types c) Cylinder speed, feed rate d) Cylinder type, feed rate

Description : Crop factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder types c) Cylinder speed, feed rate d) Cylinder type, feed rate

Last Answer : Variety of crop, Moisture in crop material

Operational factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate

Description : Operational factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate

Last Answer : Cylinder speed, feed rate

Machine factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate

Description : Machine factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate

Last Answer : Feeding chute angle, cylinder type

Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Description : Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Last Answer : F. Capacity of chaff cutters

Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Description : Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Last Answer : (d) All of the above

Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : a) 300-400rpm

In a thresher, by increasing the speed of threshing cylinder a) Threshing efficiency can be increased b) Broken grain loss can be minimized c) Un-threshed grains can be increased d) Straw breakup can be increased Ans. a

Description : In a thresher, by increasing the speed of threshing cylinder a) Threshing efficiency can be increased b) Broken grain loss can be minimized c) Un-threshed grains can be increased d) Straw breakup can be increased Ans. a

Last Answer : ans a

Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : d) 1100-1200rpm

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Last Answer : (b) Spike tooth cylinder

.total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

thresher causes more seed damage if: a speed is increased b clearance increased c speed is decreased d feed rate is reduced

Description : thresher causes more seed damage if: a speed is increased b clearance increased c speed is decreased d feed rate is reduced

Last Answer : a speed is increased

A thresher causes more seed damage if 1. Speed is increased 2. Clearance is increased 3. Feed rate is reduced 4. speed is reduced

Description : A thresher causes more seed damage if 1. Speed is increased 2. Clearance is increased 3. Feed rate is reduced 4. speed is reduced

Last Answer : ans 1

The thresher caused More seed damage if A. Speed is increases B. Clearance is increase C. Feed rate is reduced. D. Speed is reduced

Description : The thresher caused More seed damage if A. Speed is increases B. Clearance is increase C. Feed rate is reduced. D. Speed is reduced

Last Answer : Speed is increases

The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Description : The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Last Answer : 35

Speed of power operated machine chaff cutter is E. 35 rpm F. 50 rpm G. 600-1000 rpm H. None of the above

Description : Speed of power operated machine chaff cutter is E. 35 rpm F. 50 rpm G. 600-1000 rpm H. None of the above

Last Answer : G. 600-1000 rpm

Speed of band operated machines chaff cutter having two knives F. 35 rpm G. 50 rpm H. 600 rpm I. 1000 rpm

Description : Speed of band operated machines chaff cutter having two knives F. 35 rpm G. 50 rpm H. 600 rpm I. 1000 rpm

Last Answer : F. 35 rpm

A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Description : A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Last Answer : a. Seed is increase

Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Description : Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Last Answer : (a) Cylinder losses

Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Last Answer : a) Cylinder losses

.The number of knives on powered chaff cutter a) 2-6 b) 1-2 c) 5-10 d) 10-20

Description : .The number of knives on powered chaff cutter a) 2-6 b) 1-2 c) 5-10 d) 10-20

Last Answer : a) 2-6

Different parts of Thresher are A) Feeding device B) Threshing cylinder C) Concave D) All of the above.

Description : Different parts of Thresher are A) Feeding device B) Threshing cylinder C) Concave D) All of the above.

Last Answer : All of the above.

.An olpad thresher is operated (A) Manually (B)By a pair of Bullocks (C)By a tractor (D)By an electric motor

Description : .An olpad thresher is operated (A) Manually (B)By a pair of Bullocks (C)By a tractor (D)By an electric motor

Last Answer : (B)By a pair of Bullocks

The ideal moisture content for the soil primary tillage operation a) Upper plastic limit of the soil b) Lower plastic limit c) Wilting Point d) All of the above

Description : The ideal moisture content for the soil primary tillage operation a) Upper plastic limit of the soil b) Lower plastic limit c) Wilting Point d) All of the above

Last Answer : a) Upper plastic limit of the soil

Flat planting predominates where a) Nature moisture content is favourable b) Rainfall is high to provide surface drainage c) Semi arid areas to conserve moisture d) None of the above

Description : Flat planting predominates where a) Nature moisture content is favourable b) Rainfall is high to provide surface drainage c) Semi arid areas to conserve moisture d) None of the above

Last Answer : a) Nature moisture content is favourable

Capacity of field choppers (chaff cutter) is affected by (a)capacity of the feed mechanism (cross sectional area) (b)Rate of advance of material through throat considered as to be the same linear speed of feed mechanism (c) density of forage material (d) all of the above

Description : Capacity of field choppers (chaff cutter) is affected by (a)capacity of the feed mechanism (cross sectional area) (b)Rate of advance of material through throat considered as to be the same linear speed of feed mechanism (c) density of forage material (d) all of the above

Last Answer : (d) all of the above

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Last Answer : c) 600-800rpm

Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Last Answer : (a) Increase threshing efficiency

iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Last Answer : ∙ Torque is a function of thermal efficiency

Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Description : Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Last Answer : d) All of the above

In a liquid limit test, the moisture content at 10 blows was 70% and that at 100 blows was 20%. The liquid limit of the soil, is (A) 35 % (B) 50 % (C) 65 % (D) None of these

Description : In a liquid limit test, the moisture content at 10 blows was 70% and that at 100 blows was 20%. The liquid limit of the soil, is (A) 35 % (B) 50 % (C) 65 % (D) None of these

Last Answer : Answer: Option C

The metering mechanism which is suitable for the metering of small seeds as well as large grains. (a) Internal double run mechanism (b) Fluted wheel mechanism (c) Stationary opening with auger (d) None of the above

Description : The metering mechanism which is suitable for the metering of small seeds as well as large grains. (a) Internal double run mechanism (b) Fluted wheel mechanism (c) Stationary opening with auger (d) None of the above

Last Answer : (a) Internal double run mechanism

Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Description : Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Last Answer : a) Fluted wheel

For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Description : For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Last Answer : D)all of these

nging the speed of feed mechanism (b) The number of knives on feed mechanism (c) Changing speed of cutter head (d) All of the above

Description : nging the speed of feed mechanism (b) The number of knives on feed mechanism (c) Changing speed of cutter head (d) All of the above

Last Answer : (d) All of the above

The grains are separated from chaff by __________. a) winnowing b)weeding c)sowing d)tilling

Description : The grains are separated from chaff by __________. a) winnowing b)weeding c)sowing d)tilling

Last Answer : a) winnowing

Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front

Description : Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front

Last Answer : a) Concave

Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Description : Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Last Answer : c) concave, convex

knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Last Answer : a)Increase the co-efficient of friction between crop stalk machine

Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front

Description : Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front

Last Answer : a) Concave

Multiple universal joint are preferred over single joint because they : A. provide higher strength B. minimize speed fluctuation C. are lighter in weight D. are more flexible

Description : Multiple universal joint are preferred over single joint because they : A. provide higher strength B. minimize speed fluctuation C. are lighter in weight D. are more flexible

Last Answer : B. minimize speed fluctuation

Lister planting or furrow planting is practiced for (a) High rainfall areas to improve surface drainage (b) Semi-arid conditions to place seed deep in moist soil (c) Areas where natural moisture conditions are favourable (d) Irrigated areas leaving more space for operation of equipments

Description : Lister planting or furrow planting is practiced for (a) High rainfall areas to improve surface drainage (b) Semi-arid conditions to place seed deep in moist soil (c) Areas where natural moisture conditions are favourable (d) Irrigated areas leaving more space for operation of equipments

Last Answer : (b) Semi-arid conditions to place seed deep in moist soil

Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Description : Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Last Answer : c. Both (a) and (b)

Roller chains are used for: a)Higher speed and higher loads b)made of high grade steel c)components are harden and polished d)All of the above

Description : Roller chains are used for: a)Higher speed and higher loads b)made of high grade steel c)components are harden and polished d)All of the above

Last Answer : d)All of the above