Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.

Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.
by

1 Answer

Answer :

Breaking of knives.
by

Related questions

is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board

Description : is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board d) Knife Section

Last Answer :   <!-- [endif] -->Knife Section

is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe

Description : is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe

Last Answer : Cutter bar

It is always provided on each end of the cutter bar to regulate the height of cut and to provide easy and smooth sliding of the cutter bar on the land. b. Plate c. pitman d. None of above

Description : It is always provided on each end of the cutter bar to regulate the height of cut and to provide easy and smooth sliding of the cutter bar on the land. b. Plate c. pitman d. None of above

Last Answer : Ans-    b. shoe

type of connecting rod which is pinned to the crankshaft with the help of a pin, which helps to transmit the cut material. a) Pitman b) Cutter bat c) Shoe d) Wearing plate

Description : type of connecting rod which is pinned to the crankshaft with the help of a pin, which helps to transmit the cut material. a) Pitman b) Cutter bat c) Shoe d) Wearing plate

Last Answer : Pitman 

Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Description : Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Last Answer : ans b

Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a

Description : Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a

Last Answer : ans a

cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c

Description : cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c

Last Answer : ans c

Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard

Description : Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard

Last Answer : ans a

are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc

Description : are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc

Last Answer : Shoe, ledger plate, wearing plate, knife, knife section, etc.

knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Last Answer : a)Increase the co-efficient of friction between crop stalk machine

nging the speed of feed mechanism (b) The number of knives on feed mechanism (c) Changing speed of cutter head (d) All of the above

Description : nging the speed of feed mechanism (b) The number of knives on feed mechanism (c) Changing speed of cutter head (d) All of the above

Last Answer : (d) All of the above

A split-phase induction squirrel-cage motor will not come up to speed, even though the rated voltage, rated frequency, and rated load are applied. The suspected trouble could be due to _____________. A. a faulty centrifugal switch B. broken rotor bars C. worn bearings D. all of the above

Description : A split-phase induction squirrel-cage motor will not come up to speed, even though the rated voltage, rated frequency, and rated load are applied. The suspected trouble could be due to _____________. A. a faulty centrifugal switch B. broken rotor bars C. worn bearings D. all of the above

Last Answer : Answer: D

.The number of knives on powered chaff cutter a) 2-6 b) 1-2 c) 5-10 d) 10-20

Description : .The number of knives on powered chaff cutter a) 2-6 b) 1-2 c) 5-10 d) 10-20

Last Answer : a) 2-6

Speed of band operated machines chaff cutter having two knives F. 35 rpm G. 50 rpm H. 600 rpm I. 1000 rpm

Description : Speed of band operated machines chaff cutter having two knives F. 35 rpm G. 50 rpm H. 600 rpm I. 1000 rpm

Last Answer : F. 35 rpm

The cutter bar is set at about to the direction of motion in order to overcome the back-pushing action of the crops. a. 90° with inward lead of 2° c. 92° with inward lead of 2° d. None of above

Description : The cutter bar is set at about to the direction of motion in order to overcome the back-pushing action of the crops. a. 90° with inward lead of 2° c. 92° with inward lead of 2° d. None of above

Last Answer : Ans-         b. 88° with inward lead of 2°  

Cutter Bar made of a) Copper b) High Grade Steel c) Cast iron d) None of the above

Description : Cutter Bar made of a) Copper b) High Grade Steel c) Cast iron d) None of the above

Last Answer : High Grade Steel

In vertical conveyor reaper, the crop to be harvested are guided by a) Star wheel b) Reel c) Row divider d) Cutter bar

Description : In vertical conveyor reaper, the crop to be harvested are guided by a) Star wheel b) Reel c) Row divider d) Cutter bar

Last Answer : Star wheel

Cutter bar is made up of which material a) High grade steel. b) Low carbon alloy steel. c) Platinum. d) High speed tool steel

Description : Cutter bar is made up of which material a) High grade steel. b) Low carbon alloy steel. c) Platinum. d) High speed tool steel

Last Answer : High grade steel

is the length of cutter bar which is recommended as per the standard of design of it. a) 4cm b) 6cm c) 2cm d) 3cm

Description : is the length of cutter bar which is recommended as per the standard of design of it. a) 4cm b) 6cm c) 2cm d) 3cm

Last Answer : 2cm

At what degree does the cutter bar is set for achieving the object ? a) 96 b) 88 c) 69 and half. d) 105

Description : At what degree does the cutter bar is set for achieving the object ? a) 96 b) 88 c) 69 and half. d) 105

Last Answer : 88

Do I really need a bagel cutter or can I just use a knife?

Description : Do I really need a bagel cutter or can I just use a knife?

Last Answer : A bagel cutter isn't necessary to cut a bagel, but it can be slightly safer than simply using a knife. This may be important for someone who has poor motor skills, such as an elderly person or ... to spend the money, find space to store it, and would actually use it before deciding to purchase.

What are the advantages of using a pastry cutter instead of a knife?

Description : What are the advantages of using a pastry cutter instead of a knife?

Last Answer : The advantages of using a pastry cutter instead of a knife are that the crust is more likely to self rise and it makes the crust flakier. It is a very useful tool!

I bought a chefs knife today; knives excite me and frighten me. What excites and frightens you at the same time?

Description : I bought a chefs knife today; knives excite me and frighten me. What excites and frightens you at the same time?

Last Answer : Fire. The joy significantly outweighs the fear, though. I’m just very, very cautious.

How many kitchen knives come in a knife block?

Description : How many kitchen knives come in a knife block?

Last Answer : It totaly depends on what kind of knife set you purchase. Usually there are at least four different knives of different sizes.

What is the best knife sharpening tool to use for kitchen knives?

Description : What is the best knife sharpening tool to use for kitchen knives?

Last Answer : The Jende Industries Guided Sharpener - JIGS for short - is the answer to your sharpening needs in the commercial kitchen, home, workshop, garage, or mancave. Who is the JIGS System for? Chefs - Every ... the reach of the JIGS. 12-26 Degree Angle Range - Actually, a little more in both directions.

Where can I find a good knife set online that includes paring knives?

Description : Where can I find a good knife set online that includes paring knives?

Last Answer : There are many place you can go online in order to find information about knife sets, including contense and pricing. Some great websites to try include www.williams-sonoma.com, www.chefsresource.com, and www.Amazon.com.

How often will I need to sharpen the knives in the Henckels EverEdge Plus 17-Piece Knife Block Set ?

Description : How often will I need to sharpen the knives in the Henckels EverEdge Plus 17-Piece Knife Block Set ?

Last Answer : Henckels EverEdge Plus 17-Piece Knife Block Set will hold their edges well if you don't abuse them.Most often they merely need to be deburred with the included steel.

267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Description : 267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Last Answer : d)All of the above

Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810

Description : Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810

Last Answer : C 705

Appointment of a Company Secretary is made by– (A) Promoters (B) Board of Directors (C) Debenture holders (D) Government

Description : Appointment of a Company Secretary is made by– (A) Promoters (B) Board of Directors (C) Debenture holders (D) Government

Last Answer : Answer: Board of Directors

The cutter bar of a tractor operated on owner makes strokes/min (a) 400 – 500 (b) 500 – 750 (c) 800 – 1200 (d) 1250 – 1500

Description : The cutter bar of a tractor operated on owner makes strokes/min (a) 400 – 500 (b) 500 – 750 (c) 800 – 1200 (d) 1250 – 1500

Last Answer : (c) 800 – 1200

The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Last Answer : D. Between the two lower Links

The cutter bar of a tractor operated mower ordinarily makes: A. 800-1200 strokes/min B. 1600-2000 strokes/min C. 2400-2800 strokes/min D. 3200-3600 strokes/min

Description : The cutter bar of a tractor operated mower ordinarily makes: A. 800-1200 strokes/min B. 1600-2000 strokes/min C. 2400-2800 strokes/min D. 3200-3600 strokes/min

Last Answer : A. 800-1200 strokes/min

o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m

Description : o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m

Last Answer : b) 2.0cm/m

enght of cutter bar for the tractor operated mower or vertical conveyor reaper is..... (a) 1.5-3.0m (b) 3.0-4.5m (c)4.5-5.5m (d) >5.5m

Description : enght of cutter bar for the tractor operated mower or vertical conveyor reaper is..... (a) 1.5-3.0m (b) 3.0-4.5m (c)4.5-5.5m (d) >5.5m

Last Answer : (a) 1.5-3.0m

Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Description : Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Last Answer : a)400-550 rpm

Pick up reels are very effective in :- a) Cutting of upright crops b) Lifting of lodged (down) crops ahead of cutter bar C) Both (a) and (b) are true d) None of the above

Description : Pick up reels are very effective in :- a) Cutting of upright crops b) Lifting of lodged (down) crops ahead of cutter bar C) Both (a) and (b) are true d) None of the above

Last Answer : C) Both (a) and (b) are true

Speed of the cutter bar in case of combine (grain) is :- a) 400 – 550 rpm b) 500 – 800 rpm C) 800 - 1000 rpm d) 1000 – 1200 rpm

Description : Speed of the cutter bar in case of combine (grain) is :- a) 400 – 550 rpm b) 500 – 800 rpm C) 800 - 1000 rpm d) 1000 – 1200 rpm

Last Answer : a) 400 – 550 rpm

In your opinion, which is better, Pitman or Gregg shorthand?

Description : In your opinion, which is better, Pitman or Gregg shorthand?

Last Answer : I personally prefer Gregg, but this purely for aesthetic purposes.

Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman

Description : Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman

Last Answer : (A) Hanger

In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right compensation, the trajectory of the cutter will be a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5) b.(0,-5), (55,-5), (55, 35), (-5, 35), (-5,-5) c.(5, 5), (5, 25), (45, 25), (45, 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Description : In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right ... , 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Last Answer : a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5)

The distance of a given tool tip from the surface of workpiece is known as….. a.Tool length b.Tool length offset H c.Cutter radius d.Compensation

Description : The distance of a given tool tip from the surface of workpiece is known as….. a.Tool length b.Tool length offset H c.Cutter radius d.Compensation

Last Answer : b.Tool length offset H

How much of lead degree is given if the cutter is set at 88 degree? a) 2-degree b) 4 degree c) 3-degree d) 5 degree

Description : How much of lead degree is given if the cutter is set at 88 degree? a) 2-degree b) 4 degree c) 3-degree d) 5 degree

Last Answer : 2-degree

In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c

Description : In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c

Last Answer : ans c

Flail mower is a mower with high speed swinging knives, operating in a. horizontal plane c. Vertical plane d. None of above

Description : Flail mower is a mower with high speed swinging knives, operating in a. horizontal plane c. Vertical plane d. None of above

Last Answer : Ans-   b. either in the horizontal plane or in the vertical plane  

harrow having curved knives. i. Spring tooth harrow. c) Acme harrow ii. Spikal tooth d) Spike tooth harrow

Description : harrow having curved knives. i. Spring tooth harrow. c) Acme harrow ii. Spikal tooth d) Spike tooth harrow

Last Answer : Acme harrow

is a common troubles in the operation of Mower. a) Knives get twisted. b) Knives get melted. c) Knives gets rusted. d) Knives gets break

Description : is a common troubles in the operation of Mower. a) Knives get twisted. b) Knives get melted. c) Knives gets rusted. d) Knives gets break

Last Answer : Knives gets break

When removing ball or roller bearings from the shaft of a motor, you should use a _____________. A. rawhide hammer B. brass mallet C. wheel puller D. soft iron pry bar

Description : When removing ball or roller bearings from the shaft of a motor, you should use a _____________. A. rawhide hammer B. brass mallet C. wheel puller D. soft iron pry bar

Last Answer : Answer: C

Is the USMC KA-BAR a good knife?

Description : Is the USMC KA-BAR a good knife?

Last Answer : Sure. It's a good knife, tough and durable for doing a lot of different jobs. There are a lot of good knives for that sort of work. Something like this might have more general ... when skinning game, a serrated section that is good for sawing through rope, and a comfortable lightweight handle.