Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above

Increasing non grain feed rate increase  
(a) Cylinder losses
(b) Seed damage  
(c) Both (a) and(b)
(d) None of the above
by

1 Answer

Answer :

(a) Cylinder losses
by

Related questions

Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above

Last Answer : a) Cylinder losses

Increasing the grain/non-grain ratio on shoe tends to _________ the shoe losses a) Decrease b) Increase c)Decrease or increase d) Equal

Description : Increasing the grain/non-grain ratio on shoe tends to _________ the shoe losses a) Decrease b) Increase c)Decrease or increase d) Equal

Last Answer : c)Decreas

Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Last Answer : (a) Increase threshing efficiency

Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Description : Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Last Answer : d) All of the above

A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Description : A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced

Last Answer : a. Seed is increase

.Increase the grain/non grain ratio on the shoe tends to the shoe losses (a) Decreases (b) Increases (c) Decrease or increase (d) Equal

Description : .Increase the grain/non grain ratio on the shoe tends to the shoe losses (a) Decreases (b) Increases (c) Decrease or increase (d) Equal

Last Answer : (d) Equal

Increase in grain/non grain ratio on the straw Walker losses (a) Decrease (b) Increases (c) Unltered (d) None of the above

Description : Increase in grain/non grain ratio on the straw Walker losses (a) Decrease (b) Increases (c) Unltered (d) None of the above

Last Answer : (b) Increases

Increase amount of non-grain material on the straw walker _______ the walker losses a) Decreases b) Increases c) Unaffected d) Equal

Description : Increase amount of non-grain material on the straw walker _______ the walker losses a) Decreases b) Increases c) Unaffected d) Equal

Last Answer : b) Increase

Increase in grain/non-grain ratio on the straw walker, _____the straw walker losses a) Decrease b) Increase c)Unaltered d) None of the above

Description : Increase in grain/non-grain ratio on the straw walker, _____the straw walker losses a) Decrease b) Increase c)Unaltered d) None of the above

Last Answer : b) Increase

Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Last Answer : a.) Decreasing cylinder peripheral speed.

Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Last Answer : a) Higher cylinder speed.

Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Last Answer : a)peripheral speed of the drum

349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss

Description : 349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss

Last Answer : (d) Gathering loss

.Incresase amount of the non grain material on the straw Walker the walker (a) Decrease (b) Increase (c) Unaffected (d) Equal

Description : .Incresase amount of the non grain material on the straw Walker the walker (a) Decrease (b) Increase (c) Unaffected (d) Equal

Last Answer : b) Increase

Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Last Answer : M. Cylinder peripheral speed

Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism

Description : Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism

Last Answer : (d) Inclined plate metering mechanism

Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss

Description : Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss

Last Answer : (b) Shoe loss

Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss

Description : Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss

Last Answer : (b) walker loss(rack loss)

Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss

Description : Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss

Last Answer : (a)cylinder loss

.total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Formula for established plant to the seed sown based on the delivery rate (kg/ha) is A. CI=[(E×10000) /(D×W) ]×100 B. CI=[E/(N+E) ]×100 C. Both (A) and (B) D. None of (A) and (B)

Description : Formula for established plant to the seed sown based on the delivery rate (kg/ha) is A. CI=[(E×10000) /(D×W) ]×100 B. CI=[E/(N+E) ]×100 C. Both (A) and (B) D. None of (A) and (B)

Last Answer : A. CI=[(E×10000) /(D×W) ]×100

Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Description : Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Last Answer : (d) All of the above

An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Last Answer : d) None of the above

The thresher caused More seed damage if A. Speed is increases B. Clearance is increase C. Feed rate is reduced. D. Speed is reduced

Description : The thresher caused More seed damage if A. Speed is increases B. Clearance is increase C. Feed rate is reduced. D. Speed is reduced

Last Answer : Speed is increases

Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Description : Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Last Answer : a)400-550 rpm

Total mechanical losses ( frictional losses , pumping loss in intake and exhaust and power accessories) will amount to a.10-20 % ihp b.2-10 % ihp c.20-30 % ihp d.30 -50 % ihp

Description : Total mechanical losses ( frictional losses , pumping loss in intake and exhaust and power accessories) will amount to a.10-20 % ihp b.2-10 % ihp c.20-30 % ihp d.30 -50 % ihp

Last Answer : a.10-20 % ihp

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : d) 1100-1200rpm

Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Last Answer : c) 600-800rpm

.When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Last Answer : B. L-head

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660

Description : A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660

Last Answer : a. 11

The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Last Answer : c) Spike tooth and hammer mill

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Last Answer : (b) Spike tooth cylinder

iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Last Answer : ∙ Torque is a function of thermal efficiency

Compression pressure in petrol engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) 35-40 kg/cm2

Description : Compression pressure in petrol engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) 35-40 kg/cm2

Last Answer : a) 6-10 kg/cm2

Compression pressure in diesel engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) None of the above

Description : Compression pressure in diesel engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) None of the above

Last Answer : c) 20-35 kg/cm2

Firing order of a six cylinder engine in which no two adjacent cylinder have power stroke is (a) 1 5 3 6 2 4 (b) 1 2 3 4 5 6 (c) 1 5 4 6 3 2 (d) 1 4 2 5 6 3

Description : Firing order of a six cylinder engine in which no two adjacent cylinder have power stroke is (a) 1 5 3 6 2 4 (b) 1 2 3 4 5 6 (c) 1 5 4 6 3 2 (d) 1 4 2 5 6 3

Last Answer : (a) 1 5 3 6 2 4

hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Description : hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Last Answer : (b) number of power stroke per minute for all cylinders

pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement

Description : pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement

Last Answer : c) Both (a) and (b)

In a thresher, by increasing the speed of threshing cylinder a) Threshing efficiency can be increased b) Broken grain loss can be minimized c) Un-threshed grains can be increased d) Straw breakup can be increased Ans. a

Description : In a thresher, by increasing the speed of threshing cylinder a) Threshing efficiency can be increased b) Broken grain loss can be minimized c) Un-threshed grains can be increased d) Straw breakup can be increased Ans. a

Last Answer : ans a

Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Description : Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Last Answer : B. CI=[E/(N+E) ]×100

ed planting is practiced for row crops in (a) Semi-arid conditions to place seed deep in moist soil (b) High rainfall areas to improve surface drainage (c) Irrigated areas leaving more space for operation of equipments (d) Both (b) and (c)

Description : ed planting is practiced for row crops in (a) Semi-arid conditions to place seed deep in moist soil (b) High rainfall areas to improve surface drainage (c) Irrigated areas leaving more space for operation of equipments (d) Both (b) and (c)

Last Answer : d) Both (b) and (c)

The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance between the speed pick up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Description : For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Last Answer : D)all of these

nging the speed of feed mechanism (b) The number of knives on feed mechanism (c) Changing speed of cutter head (d) All of the above

Description : nging the speed of feed mechanism (b) The number of knives on feed mechanism (c) Changing speed of cutter head (d) All of the above

Last Answer : (d) All of the above

Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle

Description : Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle

Last Answer : a)Increasing disc angle

Free (threshed) seed carried over straw discharge from the rear of shoe is called:- a) Cylinder loss b) Walker losses ( rack loss) C) Shoe loss d) Gathering losses

Description : Free (threshed) seed carried over straw discharge from the rear of shoe is called:- a) Cylinder loss b) Walker losses ( rack loss) C) Shoe loss d) Gathering losses

Last Answer : C) Shoe loss

Free (threshed) seed carried over the Walker or rack in straw and discharge from the rear of machine is called as :- a) Cylinder loss b) Walker losses (rack loss) C) Shoe loss d) Gathering losses

Description : Free (threshed) seed carried over the Walker or rack in straw and discharge from the rear of machine is called as :- a) Cylinder loss b) Walker losses (rack loss) C) Shoe loss d) Gathering losses

Last Answer : b) Walker losses (rack loss)