Description : o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m
Last Answer : b) 2.0cm/m
Description : Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism
Last Answer : (d) Inclined plate metering mechanism
Description : Flooding nozzles are generally operated with (a) Axis vertical (b) Axis horizontal (c) Inclined (d) None of the above
Last Answer : (a) Axis vertical
Description : Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss
Last Answer : (b) Shoe loss
Description : Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss
Last Answer : (b) walker loss(rack loss)
Description : Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss
Last Answer : (a)cylinder loss
Description : The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links
Last Answer : d) Between two lower links
Description : Juice extraction capacity of vertical three roller type bullock down sugercane crusher E. 50-70% F. 70-90% G. 90-100% H. 30-50%
Last Answer : E. 50-70%
Description : A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of ... N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°
Last Answer : Answer: Option B
Description : Brass is an alloy of copper and zinc having the relative percentage (A) 60-70% Cu and 30-40% Zn (B) 50-60% Cu and 40-50% Zn (C) 40-50 % Cu and 60-50% Zn (D) 30-40 % Cu and 60-70% Zn
Last Answer : A) 60-70% Cu and 30-40% Zn
Description : Variation in the drop size of seed can be minimised by (a) Using a short, smooth, small diameter tube with the discharge end close to bottom of furrow. (b) Discharging the seed directly from ... (c) Mechanically transferring the seeds from the metering unit in the furrow. (d) All of the above.
Last Answer : d) All of the above.
Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above
Last Answer : c) Both (a) and (b)
Description : Which is found on the western coast of continents between 30° and 40° latitudes?
Last Answer : Mediterranean Climate Region
Description : The anchorage value of a hook is assumed sixteen times the diameter of the bar if the angle of the bend, is (A) 30° (B) 40° (C) 45° (D) All the above
Last Answer : Answer: Option D
Description : In any good staircase, the maximum and minimum pitch respectively should be (A) 90° and 0° (B) 75° and 30° (C) 60° and 10° (D) 40° and 25°
Last Answer : Option D
Description : If the angle of incidence formed on a concave mirror at a point is 30° then the angle of reflection will be: (1) 15° (2) 30° (3) 60° (4) 90°
Last Answer : (2) 30° Explanation: The angle between the incident ray and the normal is known as the angle of inci dence. The angle between the reflected ray and the normal is known as the angle of reflection.
Description : The angle in which a cricket ball should be hit to travel maximum horizontal distance is : (1) 60° with horizontal (2) 45° with horizontal (3) 30° with horizontal (4) 15° with horizontal
Last Answer : (2) 45° with horizontal Explanation: This has to do with the equation of a parabola or trajectory which is z = (tane)x 2 cos 9) 2. We can see that if the ball is fired at a 45 degree angle from the ground, the horizontal distance will be a maximum.
Description : The maximum slope of a belt conveyor can be (A) 15° (B) 30° (C) 45° (D) 60
Last Answer : (B) 30°
Description : In a right angle bend of a road provided with a transition throughout, the maximum polar angle will be (A) 10° (B) 15° (C) 20° (D) 30°
Description : If a Lemniscate curve of transition throughout is introduced to connect two parallel roads, the maximum polar angle of the curve, is (A) 10° (B) 15° (C) 20° (D) 30°
Description : The tilt angle varies form…° to….. °. For a good plough a. 20°,30°. c) 15°,30° b. 10°,30°. d) 15°,25°
Last Answer : 15°,25°
Description : The disc angle of a good plough varies between a) 25°-30° b) 10°-15° c) 18°-24° d) 42°-45°
Last Answer : 42°-45°
Last Answer : 45° with horizontal
Description : Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front
Last Answer : a) Concave
Description : Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front
Description : Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front
Last Answer : c) concave, convex
Description : Worm gear are used for transmitting power between two Shaft Inclined at e. At right angle to each other and axes can intersect f. At right angle to each other but axis cannot intersect each other g. At right angle to each other and in different planes h. None of the above
Last Answer : f. At right angle to each other but axis cannot intersect each other
Description : Spiral gear are used for transmitting power between two shaft Inclined at a. Right angle to each other and axes can intersect b. Right angle to each other and axes cannot intersect c. At angle slightly lesser or greater than 90 of axles can meet d. None of the above
Last Answer : c. At angle slightly lesser or greater than 90 of axles can meet
Description : Cut-off device is not required with (a) Inclined plate metering (b) Horizontally plate metering (c) Vertically plate metering (d) All of the above
Last Answer : (a) Inclined plate metering
Description : Penetration of disc plough can be improved by a) Increase disc angle b) Decreasing tilt angle c) Both (a) and (b) d) None of the above
Last Answer : b) Decreasing tilt angle
Description : Tabling process used for separating two materials of different densities by passing the dilute pulp over a table/deck, which is inclined from the horizontal surface at an angle of about (A) 1 to 2° (B) 2 to 5° (C) 5 to 10° (D) 10 to 15°
Last Answer : (B) 2 to 5°
Description : Spary angle for fan nozzle and hollow cone nozzle a) 40-50 b) 50-60 c) 60-95 d) 100-150
Last Answer : c) 60-95
Description : Spray Angle for fan nozzles and hollow cone nozzle a) 40-50 b) 50-60 c) 60-95 d) 100-150
Description : Alternators are preferred over dynamo because A. Alternators can produce a strong current of 30-40 amperes. B. Alternators don’t required cutout reiny C. Alternators don’t have commutaters D. All of the above
Last Answer : D. All of the above
Description : Hollow cone nozzles employed on boom type of sprayers have spray angle between : A .30-60° B.40-60° C.60-95° D.100-150°
Last Answer : C.60-95°
Description : In standard disc plow the tilk angel varies between: A.30-40 ° B.40-45° C.20-25° D.2-3°
Last Answer : C.20-25°
Description : Total mechanical losses ( frictional losses , pumping loss in intake and exhaust and power accessories) will amount to a.10-20 % ihp b.2-10 % ihp c.20-30 % ihp d.30 -50 % ihp
Last Answer : a.10-20 % ihp
Description : Injection pressure of fuel nozzle in diesel engine is a) 30-45 kg/cm2 b) 50-100 kg/cm2 c) 120-200 kg/cm2 d) 200 kg/cm2
Last Answer : c) 120-200 kg/cm2
Description : pecific gravity of fully charged storage battery is ∙ 1.15 ∙ 1.50 ∙ 1.28 ∙ 2.15
Last Answer : ∙ 1.28
Description : enght of cutter bar for the tractor operated mower or vertical conveyor reaper is..... (a) 1.5-3.0m (b) 3.0-4.5m (c)4.5-5.5m (d) >5.5m
Last Answer : (a) 1.5-3.0m
Description : In what form are the boiler tube arrange in Lamont boiler ? a. Parallel in vertical b. Inclined vertically c. Parallel in horizontal d. Horizontally inclined
Last Answer : c. Parallel in horizontal
Description : The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.
Last Answer : 35
Description : Increasing the grain/non-grain ratio on shoe tends to _________ the shoe losses a) Decrease b) Increase c)Decrease or increase d) Equal
Last Answer : c)Decreas
Description : Two bodies of mass 6 kg and 9 kg are connected with a light inextensile string passing over a smooth pulley with one of the bodies on a smooth inclined plane (θ = 30°) and the other hanging freely from the ... kg up the entire length is half the time taken by 6 kg to pull 9 kg over the same plane.
Last Answer : Given: Mass of body A (mA) = 6 kg Mass of body B (mB) = 9 kg Angle of inclination of the plane (θ) = 30° Let's assume that the acceleration of body A (aA) and body B (aB) are in opposite ... we know that the time taken (t) is given by the formula: t = √(2d/a), where d is the distance travelled
Description : A ladder is inclined to a wall making an angle of 30° with it. A man is ascending the ladder at the rate of 3 m/sec. How fast is he approaching the wa
Last Answer : A ladder is inclined to a wall making an angle of 30° with it. A man is ascending the ladder at the ... 3 m/sec. How fast is he approaching the wall ?
Description : Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec
Last Answer : B. 18-20m/sec
Description : hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder
Last Answer : (b) number of power stroke per minute for all cylinders
Description : Closer group spacing and accurate hill spacing is obtained with a) Rotary valve b) Transfer wheel c)Both a & b d)All of the above
Last Answer : c)Both a & b
Description : Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)
Last Answer : B. CI=[E/(N+E) ]×100
Description : Formula for established plant to the seed sown based on the delivery rate (kg/ha) is A. CI=[(E×10000) /(D×W) ]×100 B. CI=[E/(N+E) ]×100 C. Both (A) and (B) D. None of (A) and (B)
Last Answer : A. CI=[(E×10000) /(D×W) ]×100