A relative short and broad mould board is curved rather abruptly near the top resulting in a greater degree of pulverization is called a. Sod bottom b. Stubble bottom b. General bottom d. Slat bottom

A relative short and broad mould board is curved rather abruptly near the top resulting in a  greater degree of pulverization is called
 a. Sod bottom b. Stubble bottom
 b. General bottom d. Slat bottom
by

1 Answer

Answer :

b. General bottom
by

Related questions

A long jow mould board with a gradual twist (spiral) that completely inverts the furrow slice with a minimum of break up thus covering vegetative matter thoroughly is called a. Sod bottom b. Stubble bottom c. General bottom d. Slat bottom

Description : A long jow mould board with a gradual twist (spiral) that completely inverts the furrow slice with a minimum of break up thus covering vegetative matter thoroughly is called a. Sod bottom b. Stubble bottom c. General bottom d. Slat bottom

Last Answer : a. Sod bottom

A low mold board with gradual twist that completely invert the furrow slice with a minimum of breakup, thus covering vegetative matter thoroughly is called a. Stubble bottom b. sod bottom c. salted mould board d. general purpose bottom

Description : A low mold board with gradual twist that completely invert the furrow slice with a minimum of breakup, thus covering vegetative matter thoroughly is called a. Stubble bottom b. sod bottom c. salted mould board d. general purpose bottom

Last Answer : b. sod bottom

A slat mould board scours better than a solid mould board because of smaller contact area resulting in a) Reduction of adhesive force b) Increase in soil pressure c) Both (a) and (b) d) None of the above

Description : A slat mould board scours better than a solid mould board because of smaller contact area resulting in a) Reduction of adhesive force b) Increase in soil pressure c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Stubble bottom mold board is used where a) Pulverization is needed b) Inversion is needed c) Both d) None of these Ans. a

Description : Stubble bottom mold board is used where a) Pulverization is needed b) Inversion is needed c) Both d) None of these Ans. a

Last Answer : ans a

Sod bottom mold board is used where a) Pulverization is needed b) Inversion is needed c) Both d) None of these Ans. b

Description : Sod bottom mold board is used where a) Pulverization is needed b) Inversion is needed c) Both d) None of these Ans. b

Last Answer : ans b

This type mould boards plough is used for tough soil of grasses. a. slat c. Stubble d. None of the above

Description : This type mould boards plough is used for tough soil of grasses. a. slat c. Stubble d. None of the above

Last Answer : Ans- b. Sod or breaker

This type mould boars plough is used for sticky soil. b. Sod or breaker c. Stubble d. None of the above

Description : This type mould boars plough is used for sticky soil. b. Sod or breaker c. Stubble d. None of the above

Last Answer : Ans –a. Slat type

.Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely

Description : .Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely

Last Answer : c) No affect

…………………………... moves the trash and roots from ahead of shin towords the main furrow so as 10 ensure complete coverage by the plough bottom a. Coulter b. Jointer c. Mould board d. Shin

Description : …………………………... moves the trash and roots from ahead of shin towords the main furrow so as 10 ensure complete coverage by the plough bottom a. Coulter b. Jointer c. Mould board d. Shin

Last Answer : b. Jointer

A mould board plough bottom acts as a a. Single sided wedge b. Double sided wedge c. Three sided wedge d. All of the above

Description : A mould board plough bottom acts as a a. Single sided wedge b. Double sided wedge c. Three sided wedge d. All of the above

Last Answer : c. Three sided wedg

A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Description : A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Last Answer : D. All of the above

.The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel

Description : .The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel

Last Answer : D. Soft Centre steel

The landside of a mould board plough is made of: a) Malleable iron b) Forged steel c) C45 steel d) Soft centre steel

Description : The landside of a mould board plough is made of: a) Malleable iron b) Forged steel c) C45 steel d) Soft centre steel

Last Answer : d) Soft centre steel

A power tiller is relatively more suitable for : A. Puddling of low land paddy fields with a rotary tiller B. Primary tillage of upland paddy fields with a rotary tillers C. Primary tillage with a mould board plough D. Farm transportation work

Description : A power tiller is relatively more suitable for : A. Puddling of low land paddy fields with a rotary tiller B. Primary tillage of upland paddy fields with a rotary tillers C. Primary tillage with a mould board plough D. Farm transportation work

Last Answer : A. Puddling of low land paddy fields with a rotary tiller

owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four

Description : owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four

Last Answer : c) Three

Mould board are usually made from a. Soft centre steel b. Hardened carbon steel c. Chilled cast iron d. Mild steel

Description : Mould board are usually made from a. Soft centre steel b. Hardened carbon steel c. Chilled cast iron d. Mild steel

Last Answer : a. Soft centre steel

Center of resistence of a mould board plow less at distance equal to A. 1/4th the size of plow from the share wing B. 3/4th the size of plow from the share wing C. 2/3th the size of plow from the share wing D. 1/3th the size of plow from the share wing

Description : Center of resistence of a mould board plow less at distance equal to A. 1/4th the size of plow from the share wing B. 3/4th the size of plow from the share wing C. 2/3th the size of plow from the share wing D. 1/3th the size of plow from the share wing

Last Answer : B. 3/4th the size of plow from the share wing

Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut

Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut

Last Answer : b. Depth of cut

Rotary tillers are characterized by a) Lower and negative draft b) High power requirement c) Excessive pulverization d) All the above

Description : Rotary tillers are characterized by a) Lower and negative draft b) High power requirement c) Excessive pulverization d) All the above

Last Answer : d) All the above

Rotary tiller are wide adopted in rice cultivation due to a) Excessive pulverization b) Suitability for pudding paddy field c) Reduced draft requirement d) Complete inversion of soil

Description : Rotary tiller are wide adopted in rice cultivation due to a) Excessive pulverization b) Suitability for pudding paddy field c) Reduced draft requirement d) Complete inversion of soil

Last Answer : b) Suitability for pudding paddy field

are the types of moldboards. a) General purpose b) Stubble c) Slat d) All of above

Description : are the types of moldboards. a) General purpose b) Stubble c) Slat d) All of above

Last Answer : all of above

are the types of moldboards. a) General purpose b) Stubble c) Slat d) All of above

Description : are the types of moldboards. a) General purpose b) Stubble c) Slat d) All of above

Last Answer : All of above

.total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Description : 267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Last Answer : d)All of the above

V-shaped sweeps are best suited for a ) Primary tillage b) Stubble mulch tillage c) Rotary tillage d) Minimum tillage

Description : V-shaped sweeps are best suited for a ) Primary tillage b) Stubble mulch tillage c) Rotary tillage d) Minimum tillage

Last Answer : b) Stubble mulch tillage

turns the furrow slice used in stubble soils. a) Stubble type b) Slat type c) Share d) Jointer

Description : turns the furrow slice used in stubble soils. a) Stubble type b) Slat type c) Share d) Jointer

Last Answer :    <!-- [endif] -->Stubble type

Moldboard consists of following types : a) General purpose. c) Sod or breaker b) Stubble. d) All of the above

Description : Moldboard consists of following types : a) General purpose. c) Sod or breaker b) Stubble. d) All of the above

Last Answer : All of the above

is the general purpose lying. a) Between stubble and sod b) Between soil and mud c) Between man and machine d) None

Description : is the general purpose lying. a) Between stubble and sod b) Between soil and mud c) Between man and machine d) None

Last Answer :   <!-- [endif] -->Between stubble and sod

is used in tough soil of grasses. a) Soil b) Sod & Breaker type c) Slat type d) Plough

Description : is used in tough soil of grasses. a) Soil b) Sod & Breaker type c) Slat type d) Plough

Last Answer : Sod & Breaker type

Variation in the drop size of seed can be minimised by (a) Using a short, smooth, small diameter tube with the discharge end close to bottom of furrow. (b) Discharging the seed directly from the metering device within a few centimetres of the furrow bottom. (c) Mechanically transferring the seeds from the metering unit in the furrow. (d) All of the above.

Description : Variation in the drop size of seed can be minimised by (a) Using a short, smooth, small diameter tube with the discharge end close to bottom of furrow. (b) Discharging the seed directly from ... (c) Mechanically transferring the seeds from the metering unit in the furrow. (d) All of the above.

Last Answer : d) All of the above.

Curved twisted blades are specially suited for m. Minimum tillage of trashy land at shallow depths n. Dried hard soils o. Cutting and pulverisation in wet sticky clay soil p. For operating on the sides of plant bed

Description : Curved twisted blades are specially suited for m. Minimum tillage of trashy land at shallow depths n. Dried hard soils o. Cutting and pulverisation in wet sticky clay soil p. For operating on the sides of plant bed

Last Answer : p. For operating on the sides of plant bed

For operating rotavator on trashy soils which tines are better: A L-shaped B.Hook shaped C.Backward curved tip twist blade D.Straight blade

Description : For operating rotavator on trashy soils which tines are better: A L-shaped B.Hook shaped C.Backward curved tip twist blade D.Straight blade

Last Answer : A L-shaped

In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree

Description : In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree

Last Answer : a) less than 90 degre

ln single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree

Description : n single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree

Last Answer : c) greater than 90 degree

Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement

Description : Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement

Last Answer : b) Parasitic force

Brass is an alloy of copper and zinc having the relative percentage (A) 60-70% Cu and 30-40% Zn (B) 50-60% Cu and 40-50% Zn (C) 40-50 % Cu and 60-50% Zn (D) 30-40 % Cu and 60-70% Zn

Description : Brass is an alloy of copper and zinc having the relative percentage (A) 60-70% Cu and 30-40% Zn (B) 50-60% Cu and 40-50% Zn (C) 40-50 % Cu and 60-50% Zn (D) 30-40 % Cu and 60-70% Zn

Last Answer : A) 60-70% Cu and 30-40% Zn

The top diameter, bottom diameter and the height of a slump mould are: (A) 10 cm, 20 cm, 30 cm (B) 10 cm, 30 cm, 20 cm (C) 20 cm, 10 cm, 30 cm (D) 20 cm, 30 cm, 10 cm

Description : The top diameter, bottom diameter and the height of a slump mould are: (A) 10 cm, 20 cm, 30 cm (B) 10 cm, 30 cm, 20 cm (C) 20 cm, 10 cm, 30 cm (D) 20 cm, 30 cm, 10 cm

Last Answer : (A) 10 cm, 20 cm, 30 cm

Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The internal surface of the mould is kept clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Description : Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The ... clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Last Answer : Answer: Option D

The top diameter, bottom diameter and height of the mould used for slump test are (a) 100mm, 200mm, 300mm (b) 200mm,100mm,300mm (c) 200mm,300mm,100mm (d) 100mm,300mm,200mm

Description : The top diameter, bottom diameter and height of the mould used for slump test are (a) 100mm, 200mm, 300mm (b) 200mm,100mm,300mm (c) 200mm,300mm,100mm (d) 100mm,300mm,200mm

Last Answer : (a) 100mm, 200mm, 300mm

The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Last Answer : D. Between the two lower Links

The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links

Description : The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links

Last Answer : d) Between two lower links

The slat type mold board is used in a) Sticky soil b) Hard soil c) Loose soil d) Stoney and trashy soil Ans. a

Description : The slat type mold board is used in a) Sticky soil b) Hard soil c) Loose soil d) Stoney and trashy soil Ans. a

Last Answer : ans a

.In Hydraulic sprayers, the degree of atomization is primarily a function of A. Liquid pressure and the nozzle characteristics B. Air velocity C. Size of the nozzle D. Size and shape of the atomizer

Description : .In Hydraulic sprayers, the degree of atomization is primarily a function of A. Liquid pressure and the nozzle characteristics B. Air velocity C. Size of the nozzle D. Size and shape of the atomizer

Last Answer : A. Liquid pressure and the nozzle characteristics

In hydraulic sprayers, the degree is primarily a function of: a) Liquid pressure and the nozzle characteristics b) Air velocity c) Size of the nozzle d) Shape and size of the atomizer

Description : In hydraulic sprayers, the degree is primarily a function of: a) Liquid pressure and the nozzle characteristics b) Air velocity c) Size of the nozzle d) Shape and size of the atomizer

Last Answer : a) Liquid pressure and the nozzle characteristics

The amount of energy required to produce a given degree of pulverisation depends primarily on a) Soil strength b) Energy utilisation efficiency of tool c) Both (a) and (b) d) None of the above

Description : The amount of energy required to produce a given degree of pulverisation depends primarily on a) Soil strength b) Energy utilisation efficiency of tool c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Spiral gear are used for transmitting power between two shaft Inclined at a. Right angle to each other and axes can intersect b. Right angle to each other and axes cannot intersect c. At angle slightly lesser or greater than 90 of axles can meet d. None of the above

Description : Spiral gear are used for transmitting power between two shaft Inclined at a. Right angle to each other and axes can intersect b. Right angle to each other and axes cannot intersect c. At angle slightly lesser or greater than 90 of axles can meet d. None of the above

Last Answer : c. At angle slightly lesser or greater than 90 of axles can meet

In a horizontal plate type planter maximum obtainable value of cell fill is : A.Greater then 100% B.Less than 100% C.200% D.None of the above

Description : In a horizontal plate type planter maximum obtainable value of cell fill is : A.Greater then 100% B.Less than 100% C.200% D.None of the above

Last Answer : A.Greater then 100%

At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above

Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above

Last Answer : a) Greater contact area between furrow wall and the convex side of the disc

Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side

Description : Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side

Last Answer : c) Zero

The following strategy will promote rather than curb emergence of antibiotic resistant micro-organisms: A. Whenever possible use broad spectrum antibiotics B. Prefer a narrow spectrum antibiotic to a broad spectrum one if both are equally effective C. Prefer short and intensive courses of antibiotics D. Use antibiotic combinations for prolonged therapy

Description : The following strategy will promote rather than curb emergence of antibiotic resistant micro-organisms: A. Whenever possible use broad spectrum antibiotics B. Prefer a narrow spectrum ... Prefer short and intensive courses of antibiotics D. Use antibiotic combinations for prolonged therapy

Last Answer : A. Whenever possible use broad spectrum antibiotics