Spiral gear are used for transmitting power between two shaft Inclined at a. Right angle to each other and axes can intersect b. Right angle to each other and axes cannot intersect c. At angle slightly lesser or greater than 90 of axles can meet d. None of the above

Spiral gear are used for transmitting power between two
 shaft Inclined at
a. Right angle to each other and axes can intersect
b. Right angle to each other and axes cannot intersect
c. At angle slightly lesser or greater than 90 of axles can meet d. None of the above
by

1 Answer

Answer :

c. At angle slightly lesser or greater than 90 of axles can meet
by

Related questions

Worm gear are used for transmitting power between two Shaft Inclined at e. At right angle to each other and axes can intersect f. At right angle to each other but axis cannot intersect each other g. At right angle to each other and in different planes h. None of the above

Description : Worm gear are used for transmitting power between two Shaft Inclined at e. At right angle to each other and axes can intersect f. At right angle to each other but axis cannot intersect each other g. At right angle to each other and in different planes h. None of the above

Last Answer : f. At right angle to each other but axis cannot intersect each other

Worm gears are used for transmitting power between two shafts a)at right angle to each other and cannot intersect each other b) at right angle to each other and can intersect each other c)at angle to each other d)shafts on different plane

Description : Worm gears are used for transmitting power between two shafts a)at right angle to each other and cannot intersect each other b) at right angle to each other and can intersect each other c)at angle to each other d)shafts on different plane

Last Answer : a)at right angle to each other and cannot intersect each other

Spiral gear Is used to transmit power between two shafts place at: a)An angle to each other b)In different planes c)Both(a)and(b) d)None of the above

Description : Spiral gear Is used to transmit power between two shafts place at: a)An angle to each other b)In different planes c)Both(a)and(b) d)None of the above

Last Answer : c)Both(a)and(b)

In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree

Description : In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree

Last Answer : a) less than 90 degre

Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side

Description : Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side

Last Answer : c) Zero

ln single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree

Description : n single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree

Last Answer : c) greater than 90 degree

Flooding nozzle have spray angle a) 100-150 b) 90-100 c) 60-95 d) 30-45

Description : Flooding nozzle have spray angle a) 100-150 b) 90-100 c) 60-95 d) 30-45

Last Answer : a) 100-150

A flange coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Have lateral misalignment D. Whose axes intersect at a small angle

Description : A flange coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Have lateral misalignment D. Whose axes intersect at a small angle

Last Answer : A. Which are perfectly aligned

Oldham coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Which have lateral misalignment D. Whose axes intersect at a small angle

Description : Oldham coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Which have lateral misalignment D. Whose axes intersect at a small angle

Last Answer : C. Which have lateral misalignment

A universal coupling is used to connect two shafts A. Which are not in exact alignment B. Which are perfectly aligned C. Whose axes intersect at a small angle D. Have lateral misalignment

Description : A universal coupling is used to connect two shafts A. Which are not in exact alignment B. Which are perfectly aligned C. Whose axes intersect at a small angle D. Have lateral misalignment

Last Answer : C. Whose axes intersect at a small angle

ears commonly used on fuel injection pumps are a. Spur gears b. helical gears c. rack and pinion d. spiral gears

Description : ears commonly used on fuel injection pumps are a. Spur gears b. helical gears c. rack and pinion d. spiral gears

Last Answer : c. rack and pinion

A long jow mould board with a gradual twist (spiral) that completely inverts the furrow slice with a minimum of break up thus covering vegetative matter thoroughly is called a. Sod bottom b. Stubble bottom c. General bottom d. Slat bottom

Description : A long jow mould board with a gradual twist (spiral) that completely inverts the furrow slice with a minimum of break up thus covering vegetative matter thoroughly is called a. Sod bottom b. Stubble bottom c. General bottom d. Slat bottom

Last Answer : a. Sod bottom

Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Description : Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Last Answer : d) all of the above

The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Last Answer : D. Between the two lower Links

The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links

Description : The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links

Last Answer : d) Between two lower links

Flooding nozzles are generally operated with (a) Axis vertical (b) Axis horizontal (c) Inclined (d) None of the above

Description : Flooding nozzles are generally operated with (a) Axis vertical (b) Axis horizontal (c) Inclined (d) None of the above

Last Answer : (a) Axis vertical

Cut-off device is not required with (a) Inclined plate metering (b) Horizontally plate metering (c) Vertically plate metering (d) All of the above

Description : Cut-off device is not required with (a) Inclined plate metering (b) Horizontally plate metering (c) Vertically plate metering (d) All of the above

Last Answer : (a) Inclined plate metering

Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism

Description : Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism

Last Answer : (d) Inclined plate metering mechanism

Improved uniformity is obtained if seed tube is inclined rear ward at _________ with vertical. a)5-15° b)15-30° c)30-40° d)40-50

Description : Improved uniformity is obtained if seed tube is inclined rear ward at _________ with vertical. a)5-15° b)15-30° c)30-40° d)40-50

Last Answer : b)15-30°

Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Description : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Last Answer : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

In an epicycle gear reduction unit, the ratio of the number of teeth of the internal gears to the sun gear is: a) 3:1 b) 4:1 c) 2.5:1 d) 4.5:1

Description : In an epicycle gear reduction unit, the ratio of the number of teeth of the internal gears to the sun gear is: a) 3:1 b) 4:1 c) 2.5:1 d) 4.5:1

Last Answer : b) 4:1

Gears are generally used in the transmission box are ∙ spur gear only ∙ helical gear only ∙ helical and spur gear gears ∙ bevel gears

Description : Gears are generally used in the transmission box are ∙ spur gear only ∙ helical gear only ∙ helical and spur gear gears ∙ bevel gears

Last Answer : ∙ helical gear only

tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Description : tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Last Answer : A)sliding mesh gear box

Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Description : Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Last Answer : d. Only torque transmitting capacity of the shaft is same

When two forces acting at a point are such that if the direction of one is reversed, the direction of the resultant is turned through a right angle, the forces must be a.inclined at more than 90? b.inclined at less than 90? c.equal in magnitude d.acting at 180? e.107 dynes

Description : When two forces acting at a point are such that if the direction of one is reversed, the direction of the resultant is turned through a right angle, the forces must be a.inclined at more than 90? b.inclined at less than 90? c.equal in magnitude d.acting at 180? e.107 dynes

Last Answer : c. equal in magnitude

Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%

Description : Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%

Last Answer : A. 10-20%

Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ............................Combined radial and axial loads Which of these pairs is/are correctly matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Last Answer : (b) 1 and 2

the time taken to plough one acre farm with 35 hp tractor is : A)60 minutes b)75 minutes C)90 minutes d)120 minutes

Description : the time taken to plough one acre farm with 35 hp tractor is : A)60 minutes b)75 minutes C)90 minutes d)120 minutes

Last Answer : b)75 minutes

The sound level of an agricultural tractor should not exceed : I. 110 dB J. 100 dB K. 90 dB L. 80 dB

Description : The sound level of an agricultural tractor should not exceed : I. 110 dB J. 100 dB K. 90 dB L. 80 dB

Last Answer : K. 90 dB

Juice extraction capacity of vertical three roller type bullock down sugercane crusher E. 50-70% F. 70-90% G. 90-100% H. 30-50%

Description : Juice extraction capacity of vertical three roller type bullock down sugercane crusher E. 50-70% F. 70-90% G. 90-100% H. 30-50%

Last Answer : E. 50-70%

40 optimum working temperature for diesel engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Description : 40 optimum working temperature for diesel engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Last Answer : ∙ 88-90°c

ptimum working temperature for petrol engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Description : ptimum working temperature for petrol engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Last Answer : ∙ 71-82°c

Knuckle Joint is used to connect the two rods whose axes are coincide or intersect and lies in the same plane. A. True B. False

Description : Knuckle Joint is used to connect the two rods whose axes are coincide or intersect and lies in the same plane. A. True B. False

Last Answer : A. True

For determining the support reactions at A and B of a three hinged arch, points B and Care joined and produced to intersect the load line at D and a line parallel to the load line through A at D'. Distances AD, DD' and AD' when measured were 4 cm, 3 cm and 5 cm respectively. The angle between the reactions at A and B is (A) 30° (B) 45° (C) 60° (D) 90

Description : For determining the support reactions at A and B of a three hinged arch, points B and Care joined  and produced to intersect the load line at D and a line parallel to the load line through A at D'.  Distances AD, DD ... reactions at A and B is  (A) 30°  (B) 45°  (C) 60°  (D) 90

Last Answer : (D) 90

Curve `b^(2)x^(2) + a^(2)y^(2) = a^(2)b^(2) and m^(2)x^(2)- y^(2)l^(2) = l^(2)m^(2)` intersect each other at right-angle if:

Description : Curve `b^(2)x^(2) + a^(2)y^(2) = a^(2)b^(2) and m^(2)x^(2)- y^(2)l^(2) = l^(2)m^(2)` intersect each other at right-angle if:

Last Answer : Curve `b^(2)x^(2) + a^(2)y^(2) = a^(2)b^(2) and m^(2)x^(2)- y^(2)l^(2) = l^(2)m^(2)` intersect each ... ^(2)+m^(2)` D. `a^(2)+b^(2) = l^(2)-m^(2)`

Scouring will occur as long as a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face b) Frictional resistance at soil tool interface is more than the resistance at parallel soil-soil inter face c) Soil-metal friction is more than angle of soil shearing resistance d) None of the above

Description : Scouring will occur as long as a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face b) Frictional resistance at soil tool interface is more than ... c) Soil-metal friction is more than angle of soil shearing resistance d) None of the above

Last Answer : a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face

A power transmitting ductile material shaft under P, T and M will be designed on the basis of (a) Rankine theory (b) Guest Theory (c) Haigh theory (d) None

Description : A power transmitting ductile material shaft under P, T and M will be designed on the basis of (a) Rankine theory (b) Guest Theory (c) Haigh theory (d) None

Last Answer : (b) Guest Theory

A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Description : A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Last Answer : (c) Shear considerations only

The locus of the moment of inertia about inclined axes to the principal axis, is (A) Straight line (B) Parabola (C) Circle (D) Ellipse

Description : The locus of the moment of inertia about inclined axes to the principal axis, is  (A) Straight line  (B) Parabola  (C) Circle  (D) Ellipse

Last Answer : (D) Ellipse

In a horizontal plate type planter maximum obtainable value of cell fill is : A.Greater then 100% B.Less than 100% C.200% D.None of the above

Description : In a horizontal plate type planter maximum obtainable value of cell fill is : A.Greater then 100% B.Less than 100% C.200% D.None of the above

Last Answer : A.Greater then 100%

Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Description : Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Last Answer : A)ldler pulley

Function of idler pully are a. to increase the angle of contact of belt on pully b. maintain belt tension as belt stretches c. canter to centre distance remain same d. all the above

Description : Function of idler pully are a. to increase the angle of contact of belt on pully b. maintain belt tension as belt stretches c. canter to centre distance remain same d. all the above

Last Answer : d. all the above

swirl plate in the cone nozzle is provided to. a. Impart rotational motion to the liquid passing through it. b. To increase the droplet size. c. To decrease the droplet size. d. To increase the spray angle.

Description : swirl plate in the cone nozzle is provided to. a. Impart rotational motion to the liquid passing through it. b. To increase the droplet size. c. To decrease the droplet size. d. To increase the spray angle.

Last Answer : a. Impart rotational motion to the liquid passing through it.

Spary angle for fan nozzle and hollow cone nozzle a) 40-50 b) 50-60 c) 60-95 d) 100-150

Description : Spary angle for fan nozzle and hollow cone nozzle a) 40-50 b) 50-60 c) 60-95 d) 100-150

Last Answer : c) 60-95

Hollow cone nozzles employed on boom type of sprayers have spray angle between : A .30-60° B.40-60° C.60-95° D.100-150°

Description : Hollow cone nozzles employed on boom type of sprayers have spray angle between : A .30-60° B.40-60° C.60-95° D.100-150°

Last Answer : C.60-95°

Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above

Description : Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above

Last Answer : b) Decrease in the kinetic angle of repose

In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above

Description : In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above

Last Answer : a)Increase

Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle

Description : Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle

Last Answer : a)Increasing disc angle

The depth of penetration of a disc harrow is increased by: a) Tilt angle b) Gang angle c) Disc angle d) All of above

Description : The depth of penetration of a disc harrow is increased by: a) Tilt angle b) Gang angle c) Disc angle d) All of above

Last Answer : b) Gang angle

Disc angle adjustment influences: a. Depth of cut b. width of cut c. Soil break up d. Direction of travel

Description : Disc angle adjustment influences: a. Depth of cut b. width of cut c. Soil break up d. Direction of travel

Last Answer : b. width of cut