-For two shafts in parallel or for two concentric shafts a. T = T1 + T2 b. T = T1 = T2 c. T = T1 – T2 d. T = (T1.T2)^1/2

-For two shafts in parallel or for two concentric shafts
a. T = T1 + T2
b. T = T1 = T2
c. T = T1 – T2
d. T = (T1.T2)^1/2
by

1 Answer

Answer :

a. T = T1 + T2
by

Related questions

For two shafts in series or having different diameters for two parts of length a. T = T1 + T2 b. T = T1 = T2 c. T = T1 – T2 d. T = (T1.T2)^1/2

Description : For two shafts in series or having different diameters for two parts of length a. T = T1 + T2 b. T = T1 = T2 c. T = T1 – T2 d. T = (T1.T2)^1/2

Last Answer : b. T = T1 = T2

For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Description : For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Last Answer : b. Angle of twist

Equivalent bending moment in a shaft subjected to axial load P, torque T and bending moment M is (a) Meq = 0.5 [M + (M2 + T2)0.5]0.5 (b) Meq = 0.5 [M + (M2 + T2)0.5] (c) Meq = ( M2 + T2)0.5 (d) None

Description : Equivalent bending moment in a shaft subjected to axial load P, torque T and bending moment M is (a) Meq = 0.5 [M + (M2 + T2)0.5]0.5 (b) Meq = 0.5 [M + (M2 + T2)0.5] (c) Meq = ( M2 + T2)0.5 (d) None

Last Answer : (b) Meq = 0.5 [M + (M2 + T2)0.5]

Equivalent torque in a shaft subjected to axial load P, torque T and bending moment M is (a) Teq = (Pa2 + M2 + T2) (b) Teq = (Pa2 + M2 + T2)0.5 (c)Teq = ( M2 + T2)0.5 (d) None

Description : Equivalent torque in a shaft subjected to axial load P, torque T and bending moment M is (a) Teq = (Pa2 + M2 + T2) (b) Teq = (Pa2 + M2 + T2)0.5 (c)Teq = ( M2 + T2)0.5 (d) None

Last Answer : c)Teq = ( M2 + T2)0.5

The relation governing the torsional torque in circular shafts is a. T/r=τ/l=Gθ/J b. T/J=τ/r=Gθ/l c. T/J=τ/l=Gθ/r d. T/l=τ/r=Gθ/J

Description : The relation governing the torsional torque in circular shafts is a. T/r=τ/l=Gθ/J b. T/J=τ/r=Gθ/l c. T/J=τ/l=Gθ/r d. T/l=τ/r=Gθ/J

Last Answer : b. T/J=τ/r=Gθ/l

S1 and S2 are the draw downs in an observation well at times t1 and t2 after pumping. For discharge Q and coefficient of transmissibility T, the relationship, is (A) S2 - S1 = (2.3Q/ ) log10 (t2/t1) (B) S2 - S1 = (2.3Q/4 ) log10 (t2/t1) (C) S2 - S1 = (2.3Q/4 ) loge (t2/t1) (D) S2 - S1 = (2.3Q/4 ) loge (t1/t2

Description : S1 and S2 are the draw downs in an observation well at times t1 and t2 after pumping. For  discharge Q and coefficient of transmissibility T, the relationship, is  (A) S2 - S1 = (2.3Q/ ) log10 (t2/t1)  (B) S2 - S1 ... - S1 = (2.3Q/4 ) loge (t2/t1)  (D) S2 - S1 = (2.3Q/4 ) loge (t1/t2

Last Answer : (B) S2 - S1 = (2.3Q/4 ) log10 (t2/t1) 

Efficiency of a Carnot engine working between temperatures T1 and T2(T1 < T) is (A) (T2- T1)/T2 (B) (T2- T1)/T1 (C) (T1- T2)/T2 (D) (T1- T2)/T1

Description : Efficiency of a Carnot engine working between temperatures T1 and T2(T1 < T) is (A) (T2- T1)/T2 (B) (T2- T1)/T1 (C) (T1- T2)/T2 (D) (T1- T2)/T1

Last Answer : (A) (T2- T1)/T2

Which of the following is the Ideal gas law (equation)?  A. V/T = K  B. V= k*(1/P)  C. P1/T1 = P2/T2  D. PV = nRT

Description : Which of the following is the Ideal gas law (equation)?  A. V/T = K  B. V= k*(1/P)  C. P1/T1 = P2/T2  D. PV = nRT

Last Answer : PV = nRT

The clock period is denoted by: a. T p b. T1+T2+T3-------+T n c. Pt d. None of these

Description : The clock period is denoted by: a. T p b. T1+T2+T3-------+T n c. Pt d. None of these

Last Answer : a. T p

Let x1(t) and x2(t) be periodic with fundamental periods T1 and T2 respectively. Under what

Description : Let x1(t) and x2(t) be periodic with fundamental periods T1 and T2 respectively. Under what condition be the sum x(t) = x1(t) + x2(t) be periodic ? (A) Only for T1 = T2 (B) Always periodic (C) For T1/T2 equal to a rational number (D) Not periodic

Last Answer : Let x1(t) and x2(t) be periodic with fundamental periods T1 and T2 respectively. Under what condition be the sum x(t) = x1(t) + x2(t) be periodic ? (A) Only for T1 = T2 (B) Always periodic (C) For T1/T2 equal to a rational number (D) Not periodic

A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N

Description : A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N

Last Answer : (c) 689.7N and 4310.3N

Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm

Description : Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm

Last Answer : c. 5mm

The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring

Description : The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring

Last Answer : (d) concentric spring

For keeping the stress wholly compressive the load may be applied on a circular column anywherewithin a concentric circle of diameter (a) d/2 (b) d/3 (c) d/4 (d) d/8

Description : For keeping the stress wholly compressive the load may be applied on a circular column anywherewithin a concentric circle of diameter (a) d/2 (b) d/3 (c) d/4 (d) d/8

Last Answer : (c) d/4

Two shafts will have equal strength, if (a) diameter of both the shafts is same (b) angle of twist of both the shafts is same (c) material of both the shafts is same (d) twisting moment of both the shafts is same

Description : Two shafts will have equal strength, if (a) diameter of both the shafts is same (b) angle of twist of both the shafts is same (c) material of both the shafts is same (d) twisting moment of both the shafts is same

Last Answer : d) twisting moment of both the shafts is same

Two shafts A and B are made of the same material. The diameter of the shaft A is twice as that of shaft B. The power transmitted by the shaft A will be ........... of shaft B. (a) twice (b) four times (c) eight times (d) sixteen times

Description : Two shafts A and B are made of the same material. The diameter of the shaft A is twice as that of shaft B. The power transmitted by the shaft A will be ........... of shaft B. (a) twice (b) four times (c) eight times (d) sixteen times

Last Answer : (c) eight times

Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Description : Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Last Answer : d. Only torque transmitting capacity of the shaft is same

For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Description : For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Last Answer : c. torque

Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their shear stresses is a. 2 b. 4 c. 8 d. 16

Description : Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their shear stresses is a. 2 b. 4 c. 8 d. 16

Last Answer : c. 8

Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their angles of twist is a. 2 b. 4 c. 8 d. 16

Description : Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their angles of twist is a. 2 b. 4 c. 8 d. 16

Last Answer : d. 16

In shafts with keyways the allowable stresses are usually ------------ proportional to the twisting moment. a.25% b. 50% c. 75% d. 95%

Description : In shafts with keyways the allowable stresses are usually ------------ proportional to the twisting moment. a.25% b. 50% c. 75% d. 95%

Last Answer : c. 75%

The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Description : The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Last Answer : (d) all of above conditions are satisfied

Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Description : Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Last Answer : b) Low

Flexible shafts have ___ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Description : Flexible shafts have ___ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Last Answer : b) High

Solid shafts are used in epicyclic gearboxes. a) True b) False

Description : Solid shafts are used in epicyclic gearboxes. a) True b) False

Last Answer : b) False

The design of shafts made of brittle materials is based on (a) Guest’s theory (b) Rankine’s theory (c) St. Venant’s theory (d) Von Mises Theory

Description : The design of shafts made of brittle materials is based on (a) Guest’s theory (b) Rankine’s theory (c) St. Venant’s theory (d) Von Mises Theory

Last Answer : (b) Rankine’s theory

The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having inside diameter D/2, in torsion, is a.1/4 b. 1/2 c. 1/16 d. 15/16

Description : The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having inside diameter D/2, in torsion, is a.1/4 b. 1/2 c. 1/16 d. 15/16

Last Answer : d. 15/16

Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Description : Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Last Answer : c) Both torsional and bending

It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Description : It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Last Answer : b) Tensile

.The shafts are designed on the basis of (a) Rigidity (b) Strength (c) Both of these (d) Either of these

Description : .The shafts are designed on the basis of (a) Rigidity (b) Strength (c) Both of these (d) Either of these

Last Answer : (c) Both of these

For same length, same material, same length a. Weight of solid shaft is less than weight of hollow shaft b. Weight of solid shaft is more than weight of hollow shaft c. Weight of hollow and solid shafts will be same d. Sometime more sometime less

Description : For same length, same material, same length a. Weight of solid shaft is less than weight of hollow shaft b. Weight of solid shaft is more than weight of hollow shaft c. Weight of hollow and solid shafts will be same d. Sometime more sometime less

Last Answer : b. Weight of solid shaft is more than weight of hollow shaft

For same weight, same material, same length a. Solid shaft is always stronger than a hollow shaft b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of hollow shaft c. Strength of both the shafts in equal d. Strength of a solid shaft is always weaker and the strength ratio will depend upon Do/Di of hollow shaft

Description : For same weight, same material, same length a. Solid shaft is always stronger than a hollow shaft b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of ... of a solid shaft is always weaker and the strength ratio will depend upon Do/Di of hollow shaft

Last Answer : b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of hollow shaft

The following option is correct a. There is neither advantage nor disadvantage in transmitting power at high speed b. There is advantage in transmitting power at high speeds c. There is disadvantage in transmitting power at high speeds d. There is advantage in transmitting power at high speed provided shafts are made of high speed steel

Description : The following option is correct a. There is neither advantage nor disadvantage in transmitting power at high speed b. There is advantage in transmitting power at high speeds c. There is ... There is advantage in transmitting power at high speed provided shafts are made of high speed steel

Last Answer : b. There is advantage in transmitting power at high speeds

Which of the following is incorrect? a. In torsion equation, we use mean torque b. In torsion equation, we use maximum torque c. Many shafts are designed under combined bending and torsion load d. Shafts are also designed for torsional rigidity

Description : Which of the following is incorrect? a. In torsion equation, we use mean torque b. In torsion equation, we use maximum torque c. Many shafts are designed under combined bending and torsion load d. Shafts are also designed for torsional rigidity

Last Answer : a. In torsion equation, we use mean torque

The shafts are designed on the basis of a. strength and rigidity. b. ductility. c. malleablility. d. resilience.

Description : The shafts are designed on the basis of a. strength and rigidity. b. ductility. c. malleablility. d. resilience.

Last Answer : a. strength and rigidity.

The shafts are made of a. mild steel b. alloy steel c. copper alloys d. cast iron.

Description : The shafts are made of a. mild steel b. alloy steel c. copper alloys d. cast iron.

Last Answer : d. cast iron.

Heat transfer by radiation between two bodies at T1 & T2 and in an ambient temperature of Ta °C depends on (A) T1 - T2 (B) T1 - Ta (C) T2 - Ta (D) None of these

Description : Heat transfer by radiation between two bodies at T1 & T2 and in an ambient temperature of Ta °C depends on (A) T1 - T2 (B) T1 - Ta (C) T2 - Ta (D) None of these

Last Answer : (D) None of these

For the same draw down in two observations wells at distances r1 and r2, the times after start of pumping are t1 and t2 hours respectively. The relation which holds good is (A) t2 = r2/r1 × t1 (B) t2 = (r2/r1)² × t1 (C) t2 = (r2/r1)3 × t1 (D) t2 = (r2/r1) × t1 2

Description : For the same draw down in two observations wells at distances r1 and r2, the times after start of  pumping are t1 and t2 hours respectively. The relation which holds good is  (A) t2 = r2/r1 × t1 (B) t2 = (r2/r1)² × t1 (C) t2 = (r2/r1)3  × t1 (D) t2 = (r2/r1) × t1 2

Last Answer : (B) t2 = (r2/r1)² × t1

The ratio of equilibrium constants (Kp2/Kp1) at two different temperatures is given by (A) (R/∆H) (1/T1- 1/T2) (B) (∆H/R) (1/T1- 1/T2) (C) (∆H/R) (1/T2- 1/T1) (D) (1/R) (1/T1- 1/T2)

Description : The ratio of equilibrium constants (Kp2/Kp1) at two different temperatures is given by (A) (R/∆H) (1/T1- 1/T2) (B) (∆H/R) (1/T1- 1/T2) (C) (∆H/R) (1/T2- 1/T1) (D) (1/R) (1/T1- 1/T2)

Last Answer : (B) (∆H/R) (1/T1- 1/T2)

The equilibrium constant for a chemical reaction at two different temperatures is given by (A) Kp2/Kp1 = - (∆H/R) (1/T2- 1/T1) (B) Kp2/Kp1 = (∆H/R) (1/T2- 1/T1) (C) Kp2/Kp1 = ∆H (1/T2- 1/T1) (D) Kp2/Kp1 = - (1/R) (1/T2- 1/T1)

Description : The equilibrium constant for a chemical reaction at two different temperatures is given by (A) Kp2/Kp1 = - (∆H/R) (1/T2- 1/T1) (B) Kp2/Kp1 = (∆H/R) (1/T2- 1/T1) (C) Kp2/Kp1 = ∆H (1/T2- 1/T1) (D) Kp2/Kp1 = - (1/R) (1/T2- 1/T1)

Last Answer : (A) Kp2/Kp1 = - (∆H/R) (1/T2- 1/T1)

For heat engine operating between two temperatures (T1>T2), what is the maximum efficiency attainable?  A. Eff = 1 – (T2/T1)  B. Eff = 1 - (T1/T2)  C. Eff = T1 - T2  D. Eff = 1 - (T2/T1)^2

Description : For heat engine operating between two temperatures (T1>T2), what is the maximum efficiency attainable?  A. Eff = 1 – (T2/T1)  B. Eff = 1 - (T1/T2)  C. Eff = T1 - T2  D. Eff = 1 - (T2/T1)^2

Last Answer : Eff = 1 – (T2/T1)

The most efficient heat engine that can operate between two temperature reservoirs T1 and T2 is: w) jet engine x) internal combustion engine y) Carnot engine (pron: car-no) z) steam engine

Description : The most efficient heat engine that can operate between two temperature reservoirs T1 and T2 is: w) jet engine x) internal combustion engine y) Carnot engine (pron: car-no) z) steam engine

Last Answer : ANSWER: Y -- CARNOT ENGINE

Let the time taken to switch between user mode and kernel mode of execution be T1 while time taken to switch between two user processes be T2. Which of the following is correct? (A) T1 < T2 (B) T1 > T2 (C) T1 = T2 (D) Nothing can be said about the relation between T1 and T2.

Description : Let the time taken to switch between user mode and kernel mode of execution be T1 while time taken to switch between two user processes be T2. Which of the following is correct? (A) T1 < T2 (B) T1 > T2 (C) T1 = T2 (D) Nothing can be said about the relation between T1 and T2.

Last Answer : (A) T1 < T2

Why does CSF appears to be dark in T1 and white in T2?

Description : Why does CSF appears to be dark in T1 and white in T2?

Last Answer : I think that it is because the two types of MRI detirmine to color differently. T1 determines color based on spin-lattice relaxation time, while T2 determine color based on spin-spin relation time. Both ... dark. Since cerebrospinal fluid is mostly water, it shows up dark in T1 and light in T2.

What is the difference between T1 and T2 mri scans?

Description : What is the difference between T1 and T2 mri scans?

Last Answer : Wikipedia has some stuff to get you going: http://en.wikipedia.org/wiki/MRI#Basic_MRI_scans

If w is the angular velocity of the pulley and T1 and T2 are tensions of driving and driven side then power transmitted equals a.(T1 + T2) w b.(T1 + 2T2) w c.107 dynes d.(T1 - T2) w e.wT1

Description : If w is the angular velocity of the pulley and T1 and T2 are tensions of driving and driven side then power transmitted equals a.(T1 + T2) w b.(T1 + 2T2) w c.107 dynes d.(T1 - T2) w e.wT1

Last Answer : d. (T1 - T2) w

Let R be a relation defined on the set A of all triangles such that R = {(T1, T2) : T1 is similar to T2}. Then R is -Maths 9th

Description : Let R be a relation defined on the set A of all triangles such that R = {(T1, T2) : T1 is similar to T2}. Then R is -Maths 9th

Last Answer : (d) An equivalence relation.Every triangle is similar to itself, so (T1, T1) ∈ R ⇒ R is reflexive. (T1, T2) ∈ R ⇒ T1 ~ T2 ⇒T2 ~ T1, ⇒ (T2, T1) ∈ R ⇒ R is symmetrictransitive. ∴ R is an equivalence relation.

What digital carrier transmits a digital signal at 274.176 Mbps? A. T1 B. T3 C. T2 D. T4

Description : What digital carrier transmits a digital signal at 274.176 Mbps? A. T1 B. T3 C. T2 D. T4

Last Answer : D. T4

What carrier system multiplexes 96 voice band channels into a single 6.312 Mbps data signal? A. T1 carrier system B. T2 carrier system C. T1C carrier system D. T3 carrier system

Description : What carrier system multiplexes 96 voice band channels into a single 6.312 Mbps data signal? A. T1 carrier system B. T2 carrier system C. T1C carrier system D. T3 carrier system

Last Answer : B. T2 carrier system

A digital carrier facility used to transmit a DSI-formatted signal at 1.544. Mbps. A. T2 B. T1 C. T4 D. T3

Description : A digital carrier facility used to transmit a DSI-formatted signal at 1.544. Mbps. A. T2 B. T1 C. T4 D. T3

Last Answer : B. T1