In the theorem of three moments a.both end sinking are considered b.one end sinking is considered c.sinking is neglected d.sinking is modified by a factor

In the theorem of three moments  
a.both end sinking are considered
b.one end sinking is considered
c.sinking is neglected
d.sinking is modified by a factor
by

1 Answer

Answer :

a.both end sinking are considered
by

Related questions

In the theorem of three moments in the most general form a.two flexural rigidity are considered b. only one flexural rigidity is considered c.no flexural rigidity is considered d.flexural rigidity is doubled

Description : In the theorem of three moments in the most general form a.two flexural rigidity are considered b. only one flexural rigidity is considered c.no flexural rigidity is considered d.flexural rigidity is doubled

Last Answer : a.two flexural rigidity are considered

Sinking of support effects the a. deflection at supports b. moments at supports c. fixity d. deformation at supports

Description : Sinking of support effects the a. deflection at supports b. moments at supports c. fixity d. deformation at supports

Last Answer : b. moments at supports

A continuous beam is simply supported on its one or both the end supports the fixing moment on simply supported beam end is a. zero b. infinite c. neglected in calculation d. multiplied by a cross over factor in calculation

Description : A continuous beam is simply supported on its one or both the end supports the fixing moment on simply supported beam end is a. zero b. infinite c. neglected in calculation d. multiplied by a cross over factor in calculation

Last Answer : a. zero

When sinking is accounted in a continuous beam the bending moment is a. modified b.same c.zero d.infinite

Description : When sinking is accounted in a continuous beam the bending moment is a. modified b.same c.zero d.infinite

Last Answer : a. modified

When sinking is accounted in a continuous beam the shear force is a.modified b.same c.zero d.infinite

Description : When sinking is accounted in a continuous beam the shear force is a.modified b.same c.zero d.infinite

Last Answer : a.modified

In moment distribution method any unbalanced moment at a joint is a. neglected b. multiplied by a factor to solve c. distributed in the spans d.considered infinite

Description : In moment distribution method any unbalanced moment at a joint is a. neglected b. multiplied by a factor to solve c. distributed in the spans d.considered infinite

Last Answer : c. distributed in the spans

Byclapeyron’s theorem, the fixing moments of imaginary points are a. 0 b. 1 c. 2 d. 3

Description : Byclapeyron’s theorem, the fixing moments of imaginary points are a. 0 b. 1 c. 2 d. 3

Last Answer : a. 0

In moment distribution method the effect of applies moment on adjacent joints are a. neglected b. carried over c. multiplied by a factor before applying d. distributed over the span

Description : In moment distribution method the effect of applies moment on adjacent joints are a. neglected b. carried over c. multiplied by a factor before applying d. distributed over the span

Last Answer : b. carried over

In continuous beam if it is end is fixed supported the bending moment will be a. zero b. neglected c. infinite

Description : In continuous beam if it is end is fixed supported the bending moment will be a. zero b. neglected c. infinite

Last Answer : a. zero

In continuous beam if it is end simply supported the bending moment will be a. zero b. neglected c. infinite

Description : In continuous beam if it is end simply supported the bending moment will be a. zero b. neglected c. infinite

Last Answer : a. zero

In a mid point loaded fixed beam, the end number of moments created are a.2 b.3 c.4 d.1

Description : In a mid point loaded fixed beam, the end number of moments created are a.2 b.3 c.4 d.1

Last Answer : a.2

.Freely supported beams are assumed to be fixed beams if subjected to a. end loads which makes displacement zero b. end moments c. end couples which makes slope zero d. moments

Description : .Freely supported beams are assumed to be fixed beams if subjected to a. end loads which makes displacement zero b. end moments c. end couples which makes slope zero d. moments

Last Answer : c. end couples which makes slope zero

A shaft is said to be in pure torsion if a. Turning moment is applied at one end and other end is free b. Turning force is applied at one end and other end is free c. Two opposite turning moments are applied to the shaft d. Combination of torsional load and bending load is applied to the shaft

Description : A shaft is said to be in pure torsion if a. Turning moment is applied at one end and other end is free b. Turning force is applied at one end and other end is free c. Two opposite turning moments are applied to the shaft d. Combination of torsional load and bending load is applied to the shaft

Last Answer : c. Two opposite turning moments are applied to the shaft

In a fixed beam the total change of slope along the span is a. Zero b.infinite c. neglected d.assumed to be unit value

Description : In a fixed beam the total change of slope along the span is a. Zero b.infinite c. neglected d.assumed to be unit value

Last Answer : a. Zero

A vertical column has two moments of inertia (i.e. Ixx and Iyy ). The column will tend to buckle in the direction of the (a) axis of load (b) perpendicular to the axis of load (c) maximum moment of inertia (d) minimum moment of inertia

Description : A vertical column has two moments of inertia (i.e. Ixx and Iyy ). The column will tend to buckle in the direction of the (a) axis of load (b) perpendicular to the axis of load (c) maximum moment of inertia (d) minimum moment of inertia

Last Answer : (d) minimum moment of inertia

Which factor is used to consider the effects of direct shear stress and torsional shear stress when curvature effect stress is not considered? a. Shear stress concentration factor b. Wahl shear stress concentration factor c. Both a. and b. d. None of the above

Description : Which factor is used to consider the effects of direct shear stress and torsional shear stress when curvature effect stress is not considered? a. Shear stress concentration factor b. Wahl shear stress concentration factor c. Both a. and b. d. None of the above

Last Answer : a. Shear stress concentration factor

Which of the following theorem can be used for deflection in fixed beams a. Mohr’s first theorem b. Mohr’s second theorem c. Mohr’s third theorem d.Mohr’s fourth theorem

Description : Which of the following theorem can be used for deflection in fixed beams a. Mohr’s first theorem b. Mohr’s second theorem c. Mohr’s third theorem d.Mohr’s fourth theorem

Last Answer : b. Mohr’s second theorem

Which of the following relations is used to represent theorem of perpendicular axes? (H = Vertical axis, I = Moment of inertia and K = Radius of gyration) a. IPQ = Ixx + AH2 b. IPQ = Ixx + Ak2 c. Izz = Ixx + Iyy d. Izz + Ixx + Iyy = 0

Description : Which of the following relations is used to represent theorem of perpendicular axes? (H = Vertical axis, I = Moment of inertia and K = Radius of gyration) a. IPQ = Ixx + AH2 b. IPQ = Ixx + Ak2 c. Izz = Ixx + Iyy d. Izz + Ixx + Iyy = 0

Last Answer : c. Izz = Ixx + Iyy

What is the moment of inertia acting on a rectangle of width 15 mm and depth 40 mm about base by using theorem of parallel axes? a. 320 x 103 mm4 b. 300 x 103 mm4 c. 240 x 103 mm4 d. 80 x 103 mm

Description : What is the moment of inertia acting on a rectangle of width 15 mm and depth 40 mm about base by using theorem of parallel axes? a. 320 x 103 mm4 b. 300 x 103 mm4 c. 240 x 103 mm4 d. 80 x 103 mm

Last Answer : a. 320 x 103 mm4

An earth moving equipment costs Rs. 5,00,000 and has an estimated life of 10 years and a salvage value of Rs. 50,000. What uniform annual amount must be set aside at the end of each of the 10 years for replacement if the interest rate is 8% per annum and if the sinking fund factor at 8% per annum interest rate for 10 years is 0.069? (A) Rs. 31050 (B) Rs. 34500 (C) Rs. 37950 (D) Rs. 5000

Description : An earth moving equipment costs Rs. 5,00,000 and has an estimated life of 10 years and a salvage value of Rs. 50,000. What uniform annual amount must be set aside at the end of each of the 10 years for replacement if ... years is 0.069? (A) Rs. 31050 (B) Rs. 34500 (C) Rs. 37950 (D) Rs. 5000

Last Answer : (A) Rs. 31050

A column of length (l) with both ends fixed may be considered as equivalent to a column of length __________ with both ends hinged. (a) l/8 (b) l/4 (c) l/2 (d) l

Description : A column of length (l) with both ends fixed may be considered as equivalent to a column of length __________ with both ends hinged. (a) l/8 (b) l/4 (c) l/2 (d) l

Last Answer : c) l/2

A column of length 4m with both ends fixed may be considered as equivalent to a column of length ………….with both ends hinged. (a) 2 m (b) 1 m (c) 3 m (d) 6 m

Description : A column of length 4m with both ends fixed may be considered as equivalent to a column of length ………….with both ends hinged. (a) 2 m (b) 1 m (c) 3 m (d) 6 m

Last Answer : For a long column subjected to 1 point axial compressive load, its buckling strength will be maximum when its

With a leaf spring type of suspension, interference between steering and suspension system can be (a) front end of the spring is pin joined and the rear end is shackled (b) front end of the spring is shackled and the rear end is pin joined (c) both end of the spring are shackled (d) both end of the spring are pin joined

Description : With a leaf spring type of suspension, interference between steering and suspension system can be (a) front end of the spring is pin joined and the rear end is shackled (b) front end of the spring is ... joined (c) both end of the spring are shackled (d) both end of the spring are pin joined

Last Answer : (b) front end of the spring is shackled and the rear end is pin joined

A column with maximum equivalent length has (a) both ends hinged (b) both ends fixed (c) one end fixed and the other end hinged (d) one end fixed and the other end free

Description : A column with maximum equivalent length has (a) both ends hinged (b) both ends fixed (c) one end fixed and the other end hinged (d) one end fixed and the other end free

Last Answer : (d) one end fixed and the other end free

Columns of given length, cross-section and material have different values of buckling loads for different end conditions. The strongest column is one whose (a) One end is fixed and other end is hinged (b) Both ends are hinged or pin jointed (c) One end is fixed and the other end entirely free (d) Both the ends are fixed

Description : Columns of given length, cross-section and material have different values of buckling loads for different end conditions. The strongest column is one whose (a) One end is fixed and other end is hinged (b) ... (c) One end is fixed and the other end entirely free (d) Both the ends are fixed

Last Answer : (d) Both the ends are fixed

A cantilever is a beam whose (a) Both ends are supported either on rollers or hinges (b) One end is fixed and other end is free (c) Both ends are fixed (d) Whose both or one of the end has overhang

Description : A cantilever is a beam whose (a) Both ends are supported either on rollers or hinges (b) One end is fixed and other end is free (c) Both ends are fixed (d) Whose both or one of the end has overhang

Last Answer : b) One end is fixed and other end is free

Which of the following loading is considered for the design of axles ? (a) Bending moment only (b) Twisting moment only (c) Combined bending moment and torsion (d) Combined action of bending moment, twisting moment and axial thrust

Description : Which of the following loading is considered for the design of axles ? (a) Bending moment only (b) Twisting moment only (c) Combined bending moment and torsion (d) Combined action of bending moment, twisting moment and axial thrust

Last Answer : (a) Bending moment only

Wahl suggested the correction in the stress factor to account for a. the additional transverse shear stress b. stress concentration c. fatigue stress d. axial stress

Description : Wahl suggested the correction in the stress factor to account for a. the additional transverse shear stress b. stress concentration c. fatigue stress d. axial stress

Last Answer : b. stress concentration

Value of Wahl’s stress concentration factor is always (a) > 1 (b) = 1 (c) < 1 (d) None

Description : Value of Wahl’s stress concentration factor is always (a) > 1 (b) = 1 (c) < 1 (d) None

Last Answer : (a) > 1

Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Description : Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Last Answer : (b) Bending effect

Wahl’s stress concentration factor is (a) (4C – 1)/ (4C – 3) + 0.615/C (b) (4C – 1)/ (4C – 2) + 0.615/C (c) (4C – 1)/ (4C – 4) + 0.615/C (d) None

Description : Wahl’s stress concentration factor is (a) (4C – 1)/ (4C – 3) + 0.615/C (b) (4C – 1)/ (4C – 2) + 0.615/C (c) (4C – 1)/ (4C – 4) + 0.615/C (d) None

Last Answer : (c) (4C – 1)/ (4C – 4) + 0.615/C

Find the Wahl’s factor if spring index is 6. a) 1.2020 b) 1.2424 c) 1.2525 d) 1.5252

Description : Find the Wahl’s factor if spring index is 6. a) 1.2020 b) 1.2424 c) 1.2525 d) 1.5252

Last Answer : c) 1.2525

The shear stress concentration factor (Ks) in mechanical springs is given as _____ a. (1 + 0.5 / C) b. 0.615 / C c. (1 + 0.615 / C) d. [(4C – 1) / (4C + 1)] + [0.615 / C]

Description : The shear stress concentration factor (Ks) in mechanical springs is given as _____ a. (1 + 0.5 / C) b. 0.615 / C c. (1 + 0.615 / C) d. [(4C – 1) / (4C + 1)] + [0.615 / C]

Last Answer : a. (1 + 0.5 / C)

What is the Wahl's factor if spring index is 6? a. 1.477 b. 0.995 c. 1.252 d. None of the above

Description : What is the Wahl's factor if spring index is 6? a. 1.477 b. 0.995 c. 1.252 d. None of the above

Last Answer : c. 1.252

Wahl’s stress concentration factor is (a) [(4C—1)/(4C—4)] +0.615/C (b) [(4C—1)/(4C—4)] +0.625/C (c) [(4C—1)/(4C—4)] +0.635/C (d) None

Description : Wahl’s stress concentration factor is (a) [(4C—1)/(4C—4)] +0.615/C (b) [(4C—1)/(4C—4)] +0.625/C (c) [(4C—1)/(4C—4)] +0.635/C (d) None

Last Answer : a) [(4C—1)/(4C—4)] +0.615/C

The ratio of the effective length of a column and minimum radius of gyration of its cross sectionalarea, is known (a) Buckling factor (b) Slenderness ratio (c) Crippling factor (d) None of these

Description : The ratio of the effective length of a column and minimum radius of gyration of its cross sectionalarea, is known (a) Buckling factor (b) Slenderness ratio (c) Crippling factor (d) None of these

Last Answer : (b) Slenderness ratio

Effect of applied moment at a joint on the other joints is known as the a.carry in factor b. carry over factor c.carry up factor d.carry down factor

Description : Effect of applied moment at a joint on the other joints is known as the a.carry in factor b. carry over factor c.carry up factor d.carry down factor

Last Answer : b. carry over factor

If a continuous beam is fixed on the right then the imaginary span is taken a.before the right end b. after the right end c. before the left end d. after the left end

Description : If a continuous beam is fixed on the right then the imaginary span is taken a.before the right end b. after the right end c. before the left end d. after the left end

Last Answer : b. after the right end

For a fixed beam with UDL, maximum bending moment at end is a. wL2/12 b.wL2/24 c.wL2/36 d.wL2/48

Description : For a fixed beam with UDL, maximum bending moment at end is a. wL2/12 b.wL2/24 c.wL2/36 d.wL2/48

Last Answer : a. wL2/12

A beam is called fixed beam if end slopes remain a. horizontal b.vertical c.inclined d.parabolic

Description : A beam is called fixed beam if end slopes remain a. horizontal b.vertical c.inclined d.parabolic

Last Answer : a. horizontal

A cantilever of length 3m carries a uniformly distributed load of 15KN/m over a length of 2m from the free end.If I= 108 mm4 and E= 2×105 N/mm2,find the slope at the free end? a.0.00326 rad b.0.00578 rad c.0.00677 rad d.0.00786 rad

Description : A cantilever of length 3m carries a uniformly distributed load of 15KN/m over a length of 2m from the free end.If I= 108 mm4 and E= 2×105 N/mm2,find the slope at the free end? a.0.00326 rad b.0.00578 rad c.0.00677 rad d.0.00786 rad

Last Answer : a.0.00326 rad

A cantilever of length 3 m carries a uniformly distributed load over the entire length.If the deflection at the free end is 40 mm,find the slope at the free end. a.0.0115 rad b.0.01777 rad c.0.001566 rad d.0.00144 rad

Description : A cantilever of length 3 m carries a uniformly distributed load over the entire length.If the deflection at the free end is 40 mm,find the slope at the free end. a.0.0115 rad b.0.01777 rad c.0.001566 rad d.0.00144 rad

Last Answer : b.0.01777 rad

A cantilever of length 3 m carries two point loads of 2 KN at the free end and 4KN at a distance of 1m from the free end .What is the deflection at the free end? Take E= 2×105 N/mm2and I= 108 mm4. a.2.56 mm b.3.84 mm c.1.84 mm d.5.26mm

Description : A cantilever of length 3 m carries two point loads of 2 KN at the free end and 4KN at a distance of 1m from the free end .What is the deflection at the free end? Take E= 2×105 N/mm2and I= 108 mm4. a.2.56 mm b.3.84 mm c.1.84 mm d.5.26mm

Last Answer : c.1.84 mm

A cantilever of length 3m carries a point load of 60 KN at a distance of 2m from the fixed end.If E= 2×105 and I=108, what is the deflection at the free end?. a.7 mm b.14 mm c.26 mm d.52 mm.

Description : A cantilever of length 3m carries a point load of 60 KN at a distance of 2m from the fixed end.If E= 2×105 and I=108, what is the deflection at the free end?. a.7 mm b.14 mm c.26 mm d.52 mm.

Last Answer : b.14 mm

A cantilever of length 2m carries a point load of 30KN at the free end.If I = 108 mm4 and E= 2×105 N/mm2. What is the slope of the cantilever at the free end? a.0.503 rad b.0.677 rad c. 0.003 rad d.0.008

Description : A cantilever of length 2m carries a point load of 30KN at the free end.If I = 108 mm4 and E= 2×105 N/mm2. What is the slope of the cantilever at the free end? a.0.503 rad b.0.677 rad c. 0.003 rad d.0.008

Last Answer : c. 0.003 rad

The slope at the free end of a cantilever of length 1m is 10 .If the cantilever carries a uniformly distributed load over the whole length ,then the deflection at the free end will be a.1cm b.1.309 cm c.2.618 cm. d.3.927cm.

Description : The slope at the free end of a cantilever of length 1m is 10 .If the cantilever carries a uniformly distributed load over the whole length ,then the deflection at the free end will be a.1cm b.1.309 cm c.2.618 cm. d.3.927cm.

Last Answer : b.1.309 cm

.Maximum slope in a cantilever beam with a Moment M at the free end will be a. 3ML/EI. b.2ML/EI. C. ML/EI. d. None.

Description : .Maximum slope in a cantilever beam with a Moment M at the free end will be a. 3ML/EI. b.2ML/EI. C. ML/EI. d. None.

Last Answer : C. ML/EI.

Maximum slope in a cantilever beam with UDL w over the entire length will be a. At the free end. b. At the fixed end. c. At the centre d. None.

Description : Maximum slope in a cantilever beam with UDL w over the entire length will be a. At the free end. b. At the fixed end. c. At the centre d. None.

Last Answer : a. At the free end.

Maximum deflection in a cantilever beam with UDL w over the entire length will be a. At the free end. b. At the fixed end. c. At the centre d. None.

Description : Maximum deflection in a cantilever beam with UDL w over the entire length will be a. At the free end. b. At the fixed end. c. At the centre d. None.

Last Answer : a. At the free end.

Maximum slope in a cantilever beam with W at the free end will be a.WL2/4EI b.WL2/8EI c.WL2/2EI d.None.

Description : Maximum slope in a cantilever beam with W at the free end will be a.WL2/4EI b.WL2/8EI c.WL2/2EI d.None.

Last Answer : c.WL2/2EI