In which condition the axial distance between two adjacent coils is called as pitch? a. Compressed condition b. Uncompressed condition c. Both a. and b. d. None of the above

In which condition the axial distance between two adjacent coils is called as pitch?
a. Compressed condition  
b. Uncompressed condition  
c. Both a. and b.
d. None of the above
by

1 Answer

Answer :

b. Uncompressed condition
by

Related questions

Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Description : Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Last Answer : b) It is measured in uncompressed state

Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above

Description : Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above

Last Answer : (B) solid length

If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Description : If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Last Answer : b) 40/9

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

If the spring is compressed completely and the adjacent coils touch each other,the the length of spring is called as? a) Solid length b) Compressed length c) Free length d) None of the mentioned

Description : If the spring is compressed completely and the adjacent coils touch each other,the the length of spring is called as? a) Solid length b) Compressed length c) Free length d) None of the mentioned

Last Answer : a) Solid length

Which of the following is a benefit of lossy compression over lossless? A. File sizes will always be reduced, even when compressed multiple times. B. File quality is not harmed, e.g. images will look exactly the same. C. Files can be decompressed back to their original uncompressed form. D. File sizes are usually significantly smaller.

Description : Which of the following is a benefit of lossy compression over lossless? A. File sizes will always be reduced, even when compressed multiple times. B. File quality is not harmed, e.g. ... can be decompressed back to their original uncompressed form. D. File sizes are usually significantly smaller.

Last Answer : C. Files can be decompressed back to their original uncompressed form.

Which button can be used in the Archive manager toolbar, to create a compressed file into uncompressed ? a) Open button b) Home button c) Extract d) Up button

Description : Which button can be used in the Archive manager toolbar, to create a compressed file into uncompressed ? a) Open button b) Home button c) Extract d) Up button

Last Answer : c) Extract

What is done firstly, to create a compressed and archive file into uncompressed ? a) Left clicking a file -> Open with archive manager b) Right clicking a file -> open with archive manager c) Left clicking a file -> open with Winzip d) Right clicking a file -> open with winzip

Description : What is done firstly, to create a compressed and archive file into uncompressed ? a) Left clicking a file -> Open with archive manager b) Right clicking a file -> open with archive manager c) Left clicking a file -> open with Winzip d) Right clicking a file -> open with winzip

Last Answer : b) Right clicking a file -> open with archive manager

Using gzip program an uncompressed file in the tar format is compressed in the zip format, by providing which extension ? a) tar b) tar.gz c) tar.gz d) zip

Description : Using gzip program an uncompressed file in the tar format is compressed in the zip format, by providing which extension ? a) tar b) tar.gz c) tar.gz d) zip

Last Answer : c) tar.gz

Which type of springs have only active coils? a. Helical compression springs b. Helical tension springs c. Both a. and b. d. None of the above

Description : Which type of springs have only active coils? a. Helical compression springs b. Helical tension springs c. Both a. and b. d. None of the above

Last Answer : b. Helical tension springs

In axial thrust diagram, at which point bending moment is zero? (a) Point of contra-flexure (b) Point of inflection (c) Both a. and b. (d) None of the above

Description : In axial thrust diagram, at which point bending moment is zero? (a) Point of contra-flexure (b) Point of inflection (c) Both a. and b. (d) None of the above

Last Answer : (c) Both a. and b.

The distance between the starts of two consecutive coils measured in terms of coil sides is called (a) front pitch (b) winding pitch (c) commutator pitch (d) back pitch

Description : The distance between the starts of two consecutive coils measured in terms of coil sides is called (a) front pitch (b) winding pitch (c) commutator pitch (d) back pitch

Last Answer : (b) winding pitch

A spring with 25 active coils cannot be accommodated within a given space. Hence 5 coils of the spring are cut. The stiffness of the new spring will be a. the same b. 1.25 times the original spring c. 0.8 times the original spring d. 20 times the original spring

Description : A spring with 25 active coils cannot be accommodated within a given space. Hence 5 coils of the spring are cut. The stiffness of the new spring will be a. the same b. 1.25 times the original spring c. 0.8 times the original spring d. 20 times the original spring

Last Answer : b. 1.25 times the original spring

A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately a. increased by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Last Answer : a. increased by 8 times

If a spring has plain ends then number of inactive coils is? a) 1 b) 2 c) 3 d) 0

Description : If a spring has plain ends then number of inactive coils is? a) 1 b) 2 c) 3 d) 0

Last Answer : d) 0

Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Description : Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Last Answer : b. 12.8 turns

The distance between the centres of adjacent rivets in the same row, is called (A) Pitch (B) Lap (C) Gauge (D) Staggered pitch

Description : The distance between the centres of adjacent rivets in the same row, is called (A) Pitch (B) Lap (C) Gauge (D) Staggered pitch

Last Answer : (A) Pitch

The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Last Answer : (d) Trust diagram

A railway wagon moving with a speed of 1.5m/s is brought to rest by bumper consisting of two springs. Mass of wagon is 100kg. The springs are compressed by 125mm. Calculate the maximum force acting on each spring. a) 1200N b) 1500N c) 1800N d) 2000N

Description : A railway wagon moving with a speed of 1.5m/s is brought to rest by bumper consisting of two springs. Mass of wagon is 100kg. The springs are compressed by 125mm. Calculate the maximum force acting on each spring. a) 1200N b) 1500N c) 1800N d) 2000N

Last Answer : c) 1800N

A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm

Description : A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm

Last Answer : b. 3.14 mm

A close coiled helical spring is compressed. Its wire is subjected to A. Compression B. Tension C.Shear D. Torque

Description : A close coiled helical spring is compressed. Its wire is subjected to A. Compression B. Tension C.Shear D. Torque

Last Answer : B. Tension

When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the calculated stresses are known as (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Description : When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the ... (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Last Answer : (c) Tacking rivets

Wahl suggested the correction in the stress factor to account for a. the additional transverse shear stress b. stress concentration c. fatigue stress d. axial stress

Description : Wahl suggested the correction in the stress factor to account for a. the additional transverse shear stress b. stress concentration c. fatigue stress d. axial stress

Last Answer : b. stress concentration

Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Description : Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Last Answer : (b) Bending effect

A open helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Description : A open helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Last Answer : d) None

A closed helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Description : A closed helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Last Answer : (c) Bending

A closed helical spring under axial load is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Description : A closed helical spring under axial load is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Last Answer : (a) Shear

The axial deflection of spring for the small angle of θ is given by? a) 328PDᵌN/Gd⁴ b) 8PDᵌN/Gd⁴ c) 16PDᵌN/Gd⁴ d) 8PD²N/Gdᵌ

Description : The axial deflection of spring for the small angle of θ is given by? a) 328PDᵌN/Gd⁴ b) 8PDᵌN/Gd⁴ c) 16PDᵌN/Gd⁴ d) 8PD²N/Gdᵌ

Last Answer : b) 8PDᵌN/Gd⁴

A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Description : A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Last Answer : (b) Shear stresses

When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Description : When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Last Answer : (c) Torsion

Buckling of a column occurs under (a) Axial load (b) Transverse load (c) Direct load (d) None

Description : Buckling of a column occurs under (a) Axial load (b) Transverse load (c) Direct load (d) None

Last Answer : (a) Axial load

Bending of beam occurs under (a) Axial load (b) Transverse load (c) Direct load (d) None

Description : Bending of beam occurs under (a) Axial load (b) Transverse load (c) Direct load (d) None

Last Answer : (b) Transverse load

Which of the following loading is considered for the design of axles ? (a) Bending moment only (b) Twisting moment only (c) Combined bending moment and torsion (d) Combined action of bending moment, twisting moment and axial thrust

Description : Which of the following loading is considered for the design of axles ? (a) Bending moment only (b) Twisting moment only (c) Combined bending moment and torsion (d) Combined action of bending moment, twisting moment and axial thrust

Last Answer : (a) Bending moment only

A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Description : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Last Answer : (b) 82 Mpa

Equivalent bending moment in a shaft subjected to axial load P, torque T and bending moment M is (a) Meq = 0.5 [M + (M2 + T2)0.5]0.5 (b) Meq = 0.5 [M + (M2 + T2)0.5] (c) Meq = ( M2 + T2)0.5 (d) None

Description : Equivalent bending moment in a shaft subjected to axial load P, torque T and bending moment M is (a) Meq = 0.5 [M + (M2 + T2)0.5]0.5 (b) Meq = 0.5 [M + (M2 + T2)0.5] (c) Meq = ( M2 + T2)0.5 (d) None

Last Answer : (b) Meq = 0.5 [M + (M2 + T2)0.5]

Equivalent torque in a shaft subjected to axial load P, torque T and bending moment M is (a) Teq = (Pa2 + M2 + T2) (b) Teq = (Pa2 + M2 + T2)0.5 (c)Teq = ( M2 + T2)0.5 (d) None

Description : Equivalent torque in a shaft subjected to axial load P, torque T and bending moment M is (a) Teq = (Pa2 + M2 + T2) (b) Teq = (Pa2 + M2 + T2)0.5 (c)Teq = ( M2 + T2)0.5 (d) None

Last Answer : c)Teq = ( M2 + T2)0.5

A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular

Description : A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular

Last Answer : b) Transverse loads and couples

A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47

Description : A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47

Last Answer : d. 25.47

In moment distribution method the effect of applies moment on adjacent joints are a. neglected b. carried over c. multiplied by a factor before applying d. distributed over the span

Description : In moment distribution method the effect of applies moment on adjacent joints are a. neglected b. carried over c. multiplied by a factor before applying d. distributed over the span

Last Answer : b. carried over

Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Description : Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Last Answer : (C) free length

A close coil helical spring of mean diameter D consists of n coils of diameter d. If it carries an axial load W, the energy stored in the spring, is (A) 4WD²n/d 4N (B) 4W²Dn/d 4N (C) 4W²D3n/d 4N (D) 4W²D3n²/d 4N

Description : A close coil helical spring of mean diameter D consists of n coils of diameter d. If it carries an axial  load W, the energy stored in the spring, is  (A) 4WD²n/d 4N (B) 4W²Dn/d 4N (C) 4W²D3n/d 4N (D) 4W²D3n²/d 4N

Last Answer : (C) 4W²D3n/d 4N

Spacers are provided between adjacent coils?

Last Answer : Spacers are provided between adjacent coils to provide free passage to the cooling oil.

When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring (B) Wire diameter of each spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Last Answer : (D) Square of wire diameter of each spring

In case of a 4-pole D.C. generator provided with a two layer lap winding with sixteen coils, the pole pitch will be?

Last Answer : In case of a 4-pole D.C. generator provided with a two layer lap winding with sixteen coils, the pole pitch will be 8.

Advantages of Short Pitch Coils for an Alternator

Description : Advantages of Short Pitch Coils for an Alternator

Last Answer : Advantages of Short Pitch Coils for an Alternator: (1) It gives better sinusoidal waveform by reducing the harmonic components. (2) It saves copper as length required for the connections is ... are illuminated, hysteresis & eddy current losses will be reduced and this increases the efficiency.

Identify the necessary condition for fixed beam a. bending to be as single continuous curve b.bending to be as double continuous curve c.bending to be as discontinuous curve d.bending to be as multiple continuous curve

Description : Identify the necessary condition for fixed beam a. bending to be as single continuous curve b.bending to be as double continuous curve c.bending to be as discontinuous curve d.bending to be as multiple continuous curve

Last Answer : a. bending to be as single continuous curve

The device that permits variation in the distance between the spring eyes of a leaf spring as the spring flexes is called (a) Spring shackle (b) spring U bolt (c) spring hanger (d) spring leaf

Description : The device that permits variation in the distance between the spring eyes of a leaf spring as the spring flexes is called (a) Spring shackle (b) spring U bolt (c) spring hanger (d) spring leaf

Last Answer : (a) Spring shackle

The vertical distance between the axis of the beam before and after loading at a point is called as _______ a. Deformation b. Deflection c. Slope d. None of above.

Description : The vertical distance between the axis of the beam before and after loading at a point is called as _______ a. Deformation b. Deflection c. Slope d. None of above.

Last Answer : b. Deflection

A cantilever of length 3 m carries two point loads of 2 KN at the free end and 4KN at a distance of 1m from the free end .What is the deflection at the free end? Take E= 2×105 N/mm2and I= 108 mm4. a.2.56 mm b.3.84 mm c.1.84 mm d.5.26mm

Description : A cantilever of length 3 m carries two point loads of 2 KN at the free end and 4KN at a distance of 1m from the free end .What is the deflection at the free end? Take E= 2×105 N/mm2and I= 108 mm4. a.2.56 mm b.3.84 mm c.1.84 mm d.5.26mm

Last Answer : c.1.84 mm

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. Calculate the initial pre load required to close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can’t be determined

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined

Last Answer : (b) 4674.1N