What are the specification of this engine?

What are the specification of this engine?
by

1 Answer

Answer :

It is a two-spool high-bypass ratio engine  having take-off thrust of 30,000 lbs. flat rated to  approximately +30 degree Celsius. The engine  has a single stage fan and 4 booster stages  driven by 5 low pressure turbine and 10 high  pressure compressor stages driven by 2 high  pressure turbine.
by

Related questions

What is LRU? Mention some of the LRUs in engine and airframe?

Description : What is LRU? Mention some of the LRUs in engine and airframe?

Last Answer : LRU or Line Replaceable Unit is a complex unit of the aircraft which can be quickly and easily removed while the aircraft is at bay or ramp area. It is a sealed unit designed for quick ... Valve. Some of the LRUs in airframe are all communication and navigation antennas, black box etc.

What are the modules of this engine?

Description : What are the modules of this engine?

Last Answer : There are 5 modules in this engine. They are a. Fan b. Low Pressure (LP) compressor and intermediate case c. High Pressure (HP) system d. Low Pressure turbine e. Accessory Gearbox

Which engine is installed in our (Indigo Airlines) aircraft?

Description : Which engine is installed in our (Indigo Airlines) aircraft?

Last Answer : IAE V2527-A5.

Tell me about IDG? Or How the IDG functions?

Description : Tell me about IDG? Or How the IDG functions?

Last Answer : IDG or Integrated Drive Generator is an AC generator integrated with a Constant Speed Drive or CSD. The CSD is driven by the Accessory Gear Box (AGB) which is in turn driven by the engine. Since engine speed varies

What is the range of fuelling?

Description : What is the range of fuelling?

Last Answer : A circular area of 6 meter radius from the fuelling point or fuelling nozzle is termed as the range of fuelling.

What is flap asymmetry? What will be the action should there is a flap asymmetry?

Description : What is flap asymmetry? What will be the action should there is a flap asymmetry?

Last Answer : If flaps of left and right wing are moving at different speed or the inboard and outboard flap of the same wing are moving a different speeds, then one flap will travel to a higher ... take-off thrust. The full authority type EEC is called FADEC or Full Authority Digital Electronic Control.

What are the meanings of different colours of the annunciator lights in cockpit?

Description : What are the meanings of different colours of the annunciator lights in cockpit?

Last Answer : RED: It indicates a failure in the system that requires immediate attention and action of the crew. AMBER: It indicates a failure or malfunction of a system that requires crew awareness, ... operation of a back up system. BLUE: It indicates normal operation of a temporarily used system.

How APU is started?

Description : How APU is started?

Last Answer : To start the APU a. Put the BAT switches ON. b. Push the MASTER SWITCH. A blue light will illuminate. c. Wait until FLAP OPEN indication appears on the ECAM System Display. d. Once intake flap is open ... g. Push the EXT PWR switch to OFF. h. Put the APU BLEED ON, indicated by a blue light.

How will you drain the reservoir if it is overfilled?

Description : How will you drain the reservoir if it is overfilled?

Last Answer : To drain the excess amount of fluid filled, a drain port is provided at the bottom of the yellow and green reservoir. For blue system, a drain port is provided on the blue hydraulic panel.

What are the safety precautions will you take before re-filling the hydraulic reservoirs?

Description : What are the safety precautions will you take before re-filling the hydraulic reservoirs?

Last Answer : The safety precautions for servicing of hydraulic reservoirs can be stated as below: a. Hydraulic system depressurized. b. All slats and flaps are retracted. c. Thrust reverser is closed. d. Landing gear doors closed. e. Cargo doors closed.

What does each digit and character specifies?

Description : What does each digit and character specifies?

Last Answer : IAE stands for the manufacturer International Aero Engine. V25 designates that this engine comes under original V2500 series engines. 27 designates the rated sea-level thrust of the engine as ... to install on aircraft of Airbus Industrie. 5 designates the mechanical standard of the engine.

How APU provide constant electrical supply?

Description : How APU provide constant electrical supply?

Last Answer : Once acceleration phase of starting cycle is completed, the APU rpm is governed by fly weight mechanism. Any change in the rpm of the output shaft causes the force on the flyweight to change ... rpm. Thus the APU generator can supply electrical supply of constant frequency at 400 Hz 115 V.

In aircraft operation, the centre tank is used up before wing tanks? Why?

Description : In aircraft operation, the centre tank is used up before wing tanks? Why?

Last Answer : In normal operation, first fuel from the centre tank is used and then from wing inner fuel cell and at last from the wing outer cell. The centre tank is used first in order to obtain better ... the fuel can flow from wing to engine under gravity also which is not possible from the centre tank.

Up to what altitude APU can be operated?

Description : Up to what altitude APU can be operated?

Last Answer : APU can be operated up to around FL420. Up to around FL 250, the APU can provide electrical power of 90 kVA ampere rating as well as pneumatic power for air conditioning/pressurization and ... of providing pneumatic power and electrical power it provide drops to power rating of 66 kVA.

What is THS? Why is it used?

Description : What is THS? Why is it used?

Last Answer : THS or Trimmable Horizontal Stabilizer is actually a horizontal stabilizer, or tail plane as it is sometimes called, which can change its incidence angle in flight, automatically or manually to ... angle of attack of the entire horizontal stabilizer to maintain a correct angle of attack of the

How much torque would you apply to tighten the nut of brake assembly?

Description : How much torque would you apply to tighten the nut of brake assembly?

Last Answer : 150 ft.-lbs.

What are the solvents used in compressor wash?

Description : What are the solvents used in compressor wash?

Last Answer : In eco wash, pure demineralized water is used.

What is the difference between eco wash and compressor wash?

Description : What is the difference between eco wash and compressor wash?

Last Answer : Eco wash itself is basically a compressor wash. In early compressor wash, the water being used in compressor wash are discarded as it is expelled through the engine core exhaust. But in eco wash, ... its ecological balance and that is why this type of compressor wash is termed as eco wash.

What is eco wash?

Description : What is eco wash?

Last Answer : Eco wash is the name given to compressor wash being employed in now-a-days.

What are the initial and final torque values for A321 main landing gear wheels?

Description : What are the initial and final torque values for A321 main landing gear wheels?

Last Answer : The initial or bearing setting torque value for A321 main landing gear wheel is 310 ft.-lbs. and the final torque value is 160 ft.-lbs.

What are the electrical supply provided by the different supply sources of aircraft?

Description : What are the electrical supply provided by the different supply sources of aircraft?

Last Answer : The IDGs installed on each engine and the APU generator supply 115V 400 Hz 3 phase AC supply of 90 kVA. The emergency generator i.e. CSM/G supply 115 V 400 Hz 3 phase AC supply of 5 kVA ... supply connected to the aircraft should supply 115 V 400 Hz 3 phase AC supply of 90 kVA power rating.

What are the conditions that deploys the RAT?

Description : What are the conditions that deploys the RAT?

Last Answer : RAT is automatically deployed if it senses a. Both hydraulic system EDPs failed and loss of pressure b. Failure of both AC bus 1 and 2. c. Aircraft speed is above 100 knots.

How RAT provides hydraulic and electrical power? What is the electrical supply from CSMG?

Description : How RAT provides hydraulic and electrical power? What is the electrical supply from CSMG?

Last Answer : As RAT is deployed, its blades rotates at a high speed. The shaft is connected to a driving part of blue hydraulic system emergency pressure pump. Thus the blue hydraulic system is pressurized and ... the aircraft the emergency electrical supply of 115 V 400 Hz AC supply of 5 kVA rating.

What are the systems powered by RAT?

Description : What are the systems powered by RAT?

Last Answer : RAT powers the blue hydraulic system and provides basic electrical power through Constant Speed Motor/Generator (CSM/G).

What is RAT?

Description : What is RAT?

Last Answer : RAT or Ram Air Turbine is a small unit having to small aerofoil shaped blade installed in it. When it is deployed to the incoming airstream, the blades rotate at high speed providing emergency drive for the blue hydraulic system pressure pump.

What are computers used in A321 related to landing gear and flight controls?

Description : What are computers used in A321 related to landing gear and flight controls?

Last Answer : Landing gear related computers are LGCIU - Landing Gear Control and Interface Unit BSCU - Brake and Steering Control Unit ABCU - Alternate Braking Control Unit Flight controls related ... Computer FMGC - Flight Management and Guidance Computer FCDC - Flight Control Data Concentrators

Which hydraulic system supplies brake pressure?

Description : Which hydraulic system supplies brake pressure?

Last Answer : The green system pressurized the normal braking system while the yellow hydraulic system provides hydraulic pressure for alternate braking and parking brake.

How many times we can use the brake accumulator without the system pressurized?

Description : How many times we can use the brake accumulator without the system pressurized?

Last Answer : The brake accumulator is used to supply pressurized fluid for operation of parking brake. Without the yellow system pressurized, we can apply parking brakes for a maximum of 7 times.

Where is brake accumulator located?

Description : Where is brake accumulator located?

Last Answer : The brake accumulator is located on the right hand side of the aft frame of the main landing gear wheel well area.

What is air pressure charge in hydraulic accumulators in A321?

Description : What is air pressure charge in hydraulic accumulators in A321?

Last Answer : The three system accumulators are pressurized with N2 to a pressure of 1950 psi. The brake accumulator is pressurized to 1200 psi pressure.

What have you learnt in the last 6 months? (Where have you worked recently and what have you learnt?)

Description : What have you learnt in the last 6 months? (Where have you worked recently and what have you learnt?)

Last Answer : I have undergone apprenticeship in Air India recently. I have performed wheel change, IDG oil filter change, accumulator air pressure charging, hydraulic system servicing, compressor eco wash on Airbus A321.

Which of the two hydraulic systems, Yellow and Blue, is generally used on ground? Give your reasons for that.

Description : Which of the two hydraulic systems, Yellow and Blue, is generally used on ground? Give your reasons for that.

Last Answer : Normally the yellow hydraulic system used. Firstly because, if at any point, if we require the green system to be pressurized for operation of some component, we can pressurize it with the ... need yellow hydraulic system to be pressurized. Blue system is not available for cargo door operation.

If hydraulic power is required on ground, which hydraulic system can be used and why?

Description : If hydraulic power is required on ground, which hydraulic system can be used and why?

Last Answer : Both Yellow and Blue hydraulic system can be used. Because, only Yellow and Blue hydraulic systems are equipped with electric pump?

Is there a standard cross-industry scale specification for action figures?

Description : Is there a standard cross-industry scale specification for action figures?

Last Answer : http://actionfigures.about.com/od/gettingstarted/a/action_figure_scales.htm This page has tons of good information about all the different sizes and standards of action figures.

If central heating system cannot be installed as per the clients original specification what should a plumber do?

Description : If central heating system cannot be installed as per the clients original specification what should a plumber do?

Last Answer : advise their immeddiate supervisor or employer about the problem, obtain the clients verbal agreemenet to carry out the alterations, obtain the clients written agreement to carry out the alterations, proceed when the clients quantity surveoyor issues a variationorder

If central heating system cannot be installed as per the clients original specification what should a plumber do?

Description : If central heating system cannot be installed as per the clients original specification what should a plumber do?

Last Answer : advise their immeddiate supervisor or employer about the problem, obtain the clients verbal agreemenet to carry out the alterations, obtain the clients written agreement to carry out the alterations, proceed when the clients quantity surveoyor issues a variationorder

What type of memory is not directly addressable by the CPU and requires special softw3are called EMS (expanded memory specification)? A) Extended B) Expanded C) Base D) Conventional

Description : What type of memory is not directly addressable by the CPU and requires special softw3are called EMS (expanded memory specification)? A) Extended B) Expanded C) Base D) Conventional

Last Answer : Answer : B

What is the first stage in software development? A) Specification and design B) Testing C) System Analysis D) Maintenance

Description : What is the first stage in software development? A) Specification and design B) Testing C) System Analysis D) Maintenance

Last Answer : Answer : C

What is difference between a Cursor declared in a procedure and Cursor declared in a package specification ?

Description : What is difference between a Cursor declared in a procedure and Cursor declared in a package specification ?

Last Answer : A cursor declared in a package specification is global and can be accessed by other procedures or procedures in a package. A cursor declared in a procedure is local to the procedure that can not be accessed by other procedures.

And ITU-T specification code that deals with the telephone circuits. A. X series B. T series C. V series D. I series

Description : And ITU-T specification code that deals with the telephone circuits. A. X series B. T series C. V series D. I series

Last Answer : C. V series

What is the most important specification of loudspeakers and microphones? A. Frequency response B. Power density C. Field Strength D. Gain

Description : What is the most important specification of loudspeakers and microphones? A. Frequency response B. Power density C. Field Strength D. Gain

Last Answer : A. Frequency response

If a contractor proposes to increase concrete cover beyond contractual specification (i.e. 40mm to 70mm), shall engineers accept the proposal?

Description : If a contractor proposes to increase concrete cover beyond contractual specification (i.e. 40mm to 70mm), shall engineers accept the proposal?

Last Answer : In contractual aspect, based on the requirement of General Specification of Civil Engineering Works (1992 Edition), the tolerance of concrete cover is between + ... larger cover. Therefore, with an increase of concrete cover, the crack width will increase which is undesirable.

Which act’s important specification was the provincial autonomy.

Description : Which act’s important specification was the provincial autonomy.

Last Answer : 1935

Which one of the following statements is true? a. Independ. Quality planning enables the project manager to manage the trade-off between customer expectations and budgetdent reviews and quality audits form part of quality assurance to ensure the project manager delivers on time and to budget. b. Quality assurance provides confidence to stakeholders that requirements for quality will be exceeded. c. Quality control verifies that the project deliverables conform to specification, are fit for purpose and meet stakeholder expectations.

Description : Which one of the following statements is true? a. Independent reviews and quality audits form part of quality assurance to ensure the project manager delivers on time and to budget. ... Quality planning enables the project manager to manage the trade-off between customer expectations  and budget

Last Answer : c. Quality control verifies that the project deliverables conform to specification, are fit for purpose and  meet stakeholder expectations.

Which of the following is not considered as a risk in project management? a) Specification delays b) Product competition c) Testing d) Staff turnover

Description : Which of the following is not considered as a risk in project management? a) Specification delays b) Product competition c) Testing d) Staff turnover

Last Answer : c) Testing

Which of the following can estimate size of project directly from problem specification? A. LOC B. Function Point Metric C. Both D. None

Description : Which of the following can estimate size of project directly from problem specification? A. LOC B. Function Point Metric C. Both D. None

Last Answer : B. Function Point Metric

We can accurately estimate lines of code from the problem specification. A. True B. False C. NA D. NA

Description :  We can accurately estimate lines of code from the problem specification. A. True B. False C. NA D. NA

Last Answer : B. False

Which of the following activity is undertaken immediately after feasibility study and before the requirement analysis and specification phase? A. Project Planning B. Project Monitoring C. Project Control D. Project Scheduling

Description : Which of the following activity is undertaken immediately after feasibility study and before  the requirement analysis and specification phase? A. Project Planning B. Project Monitoring C. Project Control D. Project Scheduling

Last Answer : A. Project Planning

Which of the following is not considered as a risk in project management? a) Specification delays b) Product competition c) Testing d) Staff turnover

Description : Which of the following is not considered as a risk in project management? a) Specification delays b) Product competition c) Testing d) Staff turnover

Last Answer : c) Testing

The life cycle can be said to consist of a series of phases. The classical model is referred to as the waterfall model. Which phase may be defined as “The concept is explored and refined, and the client’s requirements are elicited?” (a) Requirements (b) Specification (c) Design d) Implementation

Description : The life cycle can be said to consist of a series of phases. The  classical model is referred to as the waterfall model. Which phase  may be defined as The concept is explored and refined, ... client's requirements are elicited? (a) Requirements (b) Specification (c) Design d) Implementation

Last Answer : (a) Requirements