Fractional pitch windings are used in DC machines to

Fractional pitch windings are used in DC machines to

(A) Reduce copper losses

(B) Improve cooling

(C) Increase the generated emf

(D) Reduce sparking
by

1 Answer

Answer :

Fractional pitch windings are used in DC machines to Reduce sparking

by

Related questions

In D.C. machines fractional pitch winding is used?

Last Answer : In D.C. machines fractional pitch winding is used to reduce the sparking.

In dc machines, the armature windings are placed on the rotor because of the necessity for

Description : In dc machines, the armature windings are placed on the rotor because of the necessity for  (1) electromechanical energy conversion (2) generation of voltage (3) commutation (4) development of torque

Last Answer : 3  Commutation

Hopkinson's test on D.C. machines is conducted at?

Last Answer : Hopkinson's test on D.C. machines is conducted at full-load.

Losses in dc machine..?

Last Answer : Copper losses,iron losses,variable losses , constant losees

Explain concept of back emf in DC machine. State how it governs armature current.

Description : Explain concept of back emf in DC machine. State how it governs armature current. 

Last Answer : Back emf: When the armature of DC machine rotates under the influence of driving torque, the armature conductors move in the magnetic field and cut it and hence emf is induced in them. The ... flow of armature current i.e. it automatically changes the armature current to meet load requirements.

State the function of overload coil and No volt coil in dc motor starter.

Description : State the function of overload coil and No volt coil in dc motor starter.

Last Answer : Function of Overload Coil: When DC motor is overloaded, the overload coil carries the overload current and produces strong magnetic field to attract a plunger, which short the terminals of ... dc motor is prevented from restarting automatically on recovery of supply without starter and protected.

State any four applications of DC shunt motor.

Description : State any four applications of DC shunt motor.

Last Answer : Applications of DC shunt motor: 1) Lathe machines 2) drilling machines 3) milling machines 4) Printing machinery 5) Paper industry 6) centrifugal and reciprocating pumps 7) blowers 8)fans

State the function of commutator in DC generator and name the material used for commutator.

Description : State the function of commutator in DC generator and name the material used for commutator.

Last Answer : Function of Commutator: Commutator converts AC induced in armature winding into DC for external load. Material: i) Commutator segments are made up of Copper. ii) Commutator segments are insulated from each other by Mica.

A DC shunt motor has rated rpm of 480. Certain industrial application requires this motor to run at 540 rpm

Description : A DC shunt motor has rated rpm of 480. Certain industrial application requires this motor to run at 540 rpm for some time. Which speed control will be desirable? A) Ward Leonard control B) Armature ... ) Field resistance control D) It is not possible to run the motor at more than the rated rpm 

Last Answer : A DC shunt motor has rated rpm of 480. Certain industrial application requires this motor to run at 540 rpm for some time. Which speed control will be desirable? A) Ward Leonard control B) Armature ... Field resistance control D) It is not possible to run the motor at more than the rated rpm 

A 50 kW dc shunt is loaded to draw rated armature current at any given speed. When driven

Description : A 50 kW dc shunt is loaded to draw rated armature current at any given speed. When driven  (i) at half the rated speed by armature voltage control and (ii) at 1.5 times the rated speed by field control, the respective output powers ... kW in (i) and 75 kW in (ii) (D) 50 kW in (i) and 50 kW in (ii)

Last Answer : A 50 kW dc shunt is loaded to draw rated armature current at any given speed. When driven  (i) at half the rated speed by armature voltage control and (ii) at 1.5 times the rated speed by field control, the respective output ... kW in (i) and 75 kW in (ii) (D) 50 kW in (i) and 50 kW in (ii)

In a DC machine, which of the following statements is true ?

Description : In a DC machine, which of the following statements is true ?  (A) Compensating winding is used for neutralizing armature reaction while interpole winding is used for producing ... Compensation winding is used for improving commutation while interpole winding is used for producing residual flux

Last Answer : In a DC machine, which of the following statements is true ?  (A) Compensating winding is used for neutralizing armature reaction while interpole winding is used for producing ... Compensation winding is used for improving commutation while interpole winding is used for producing residual flux

What are the slot wedges in a DC machine made of?

Description : What are the slot wedges in a DC machine made of?   (a) Mild steel (b) Silicon steel (c) Fibre (d) Cast iron

Last Answer : What are the slot wedges in a DC machine made of?   (a) Mild steel (b) Silicon steel (c) Fibre (d) Cast iron

For continuously running rolling mills with intermittent loading, the most suitable DC drive is

Description : For continuously running rolling mills with intermittent loading, the most suitable DC drive is   (a) DC series motor (b) DC shunt motor (c) DC differentially compound motor (d) DC cumulatively compound motor 

Last Answer : For continuously running rolling mills with intermittent loading, the most suitable DC drive is DC cumulatively compound motor 

The fractional-pitch used for eliminating 7th harmonic from the emf wave of an alternator is

Description : The fractional-pitch used for eliminating 7th harmonic from the emf wave of an alternator is (A) 2/3 (B) 5/6 (C) 7/8 (D) 6/7

Last Answer : The fractional-pitch used for eliminating 7th harmonic from the emf wave of an alternator is 6/7

Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. lowers the insulation value and is a common cause of fault grounds in idle machines C. will enhance insulation resistance only if it is fresh water and contains no salt D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Description : Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. ... D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Last Answer : Answer: B

Before testing insulation with a megohmmeter, the windings of large machines should be grounded for about 15 minutes just prior to the test as the ______________. A. insulation may be damaged B. insulation may be covered with moisture C. armature windings will have a greater number of leakage paths D. larger machines may acquire a charge of static electricity during operation

Description : Before testing insulation with a megohmmeter, the windings of large machines should be grounded for about 15 minutes just prior to the test as the ______________. A. insulation may be damaged ... number of leakage paths D. larger machines may acquire a charge of static electricity during operation

Last Answer : Answer: D

Before testing insulation with a megohmmeter, the windings of large machines should be grounded for about 15 minutes just prior to the test, because the ___________. A. static charge of the machine may give a false reading B. armature will have a greater number of leakage paths C. insulation may be damaged D. insulation may be covered with moisture

Description : Before testing insulation with a megohmmeter, the windings of large machines should be grounded for about 15 minutes just prior to the test, because the ___________. A. static charge of the machine ... number of leakage paths C. insulation may be damaged D. insulation may be covered with moisture

Last Answer : Answer: A

is universally used for windings of electrical machines because it is easily workable without any possibility of fracture. (a) Silver (b) Steel (c) Aluminium (d) Copper

Description : is universally used for windings of electrical machines because it is easily workable without any possibility of fracture. (a) Silver (b) Steel (c) Aluminium (d) Copper

Last Answer : (d) Copper

Copper, even though costly, finds use in the windings of electrical machines because

Last Answer : Copper, even though costly, finds use in the windings of electrical machines because copper points offer low contact resistance , copper can be easily soldered and welded, copper windings are less bulky and the machines become compact.

In D.C. machines the usual limit of slot pitch is (a) between 5 to 10 mm (b) between 10 to 15 mm (c) between 15 to 20 mm (d) between 25 to 35 mm

Description : In D.C. machines the usual limit of slot pitch is (a) between 5 to 10 mm (b) between 10 to 15 mm (c) between 15 to 20 mm (d) between 25 to 35 mm

Last Answer : (d) between 25 to 35 mm

If overloading a DC machine becomes necessary in an emergency, you should ____________. A. cool the machine with portable blowers and fans B. hold thermal overload relays open with blocks of wood C. inject small amounts of CO2 into the windings for cooling D. increase the residual magnetism value of windings to reduce eddy currents

Description : If overloading a DC machine becomes necessary in an emergency, you should ____________. A. cool the machine with portable blowers and fans B. hold thermal overload relays open with blocks of ... the windings for cooling D. increase the residual magnetism value of windings to reduce eddy currents

Last Answer : Answer: A

An open in the armature of a DC motor is suspected, but is not found by visual inspection of the commutator. The next step in troubleshooting this problem is to ________________. A. conduct a bar to bar test of the armature B. visually inspect the armature windings C. conduct an insulation resistance test of the armature D. test the commutator for a ground

Description : An open in the armature of a DC motor is suspected, but is not found by visual inspection of the commutator. The next step in troubleshooting this problem is to ________________. A. conduct a ... windings C. conduct an insulation resistance test of the armature D. test the commutator for a ground

Last Answer : Answer: A

Which of the listed conditions could cause a DC motor to have excessively hot windings and sparking at the brushes? A. Reversed interpole polarity B. High bar-to-bar voltage C. Loose brushes D. Excessive humidity

Description : Which of the listed conditions could cause a DC motor to have excessively hot windings and sparking at the brushes? A. Reversed interpole polarity B. High bar-to-bar voltage C. Loose brushes D. Excessive humidity

Last Answer : Answer: A

Which of the listed conditions will occur if the polarity of the field poles and the direction of current to the brushes of a DC motor were both reversed? A. The motor would not start. B. The direction of rotation of the armature would be reversed. C. The direction of rotation of the armature would be unchanged. D. The field pole windings would become overheated.

Description : Which of the listed conditions will occur if the polarity of the field poles and the direction of current to the brushes of a DC motor were both reversed? A. The motor would not start. ... direction of rotation of the armature would be unchanged. D. The field pole windings would become overheated.

Last Answer : Answer: C

When an AC or a DC motor fails to start, the FIRST step in troubleshooting should be to check the ____________. A. motor windings for obvious opens B. motor controller leads for continuity C. fuse or circuit breaker D. motor controller leads for grounds

Description : When an AC or a DC motor fails to start, the FIRST step in troubleshooting should be to check the ____________. A. motor windings for obvious opens B. motor controller leads for continuity C. fuse or circuit breaker D. motor controller leads for grounds

Last Answer : Answer: C

Which of the following statements describes what will happen when both the polarity of the field poles, and the direction of current to the brushes of a DC motor are reversed? A. The motor will not start. B. The direction of rotation of the armature will be reversed. C. The direction of rotation of the armature will remain the same. D. The field pole windings will become overheated.

Description : Which of the following statements describes what will happen when both the polarity of the field poles, and the direction of current to the brushes of a DC motor are reversed? A. The motor will ... of rotation of the armature will remain the same. D. The field pole windings will become overheated.

Last Answer : Answer: C

The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Description : The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Last Answer : Answer: C

The counter EMF produced in the windings of a DC motor is 'zero' when the ____________. A. armature has just begun to turn B. armature is not turning C. motor is almost up to rated speed D. motor is at rated speed

Description : The counter EMF produced in the windings of a DC motor is 'zero' when the ____________. A. armature has just begun to turn B. armature is not turning C. motor is almost up to rated speed D. motor is at rated speed

Last Answer : Answer: B

A shunt-wound DC generator is one in which the shunt field windings are in parallel with the _____________. A. commutator B. brushes C. armature D. all of the above

Description : A shunt-wound DC generator is one in which the shunt field windings are in parallel with the _____________. A. commutator B. brushes C. armature D. all of the above

Last Answer : Answer: D

A DC shunt generator has its field windings connected in _____________. A. series with the series windings B. parallel with the field rheostat C. series with the armature windings D. parallel with the armature windings

Description : A DC shunt generator has its field windings connected in _____________. A. series with the series windings B. parallel with the field rheostat C. series with the armature windings D. parallel with the armature windings

Last Answer : Answer: D

In a DC generator the windings of interpoles are connected :

Description : In a DC generator the windings of interpoles are connected :  (A) in series with main field winding, to create a pole,of same polarity as the main pole ahead in the direction of rotation.  ... winding, to create a pole of opposite polarity as the main pole ahead in the direction of rotation.

Last Answer : In a DC generator the windings of interpoles are connected :  in series with the armature winding, to create a pole of same polarity as the main pole ahead in the direction of rotation. 

A 36 slot, 4 -pole, dc machine has a simplex lap winding with two conductors per slot. The back pitch and

Description : A 36 slot, 4 -pole, dc machine has a simplex lap winding with two conductors per slot. The back pitch and front pitch adopted could be respectively

Last Answer : A 36 slot, 4 -pole, dc machine has a simplex lap winding with two conductors per slot. The back pitch and front pitch adopted could be respectively 19,17

State the principle of operation of d.c. motor.

Description : State the principle of operation of d.c. motor.

Last Answer : When a current carrying conductor is placed in a magnetic field, the conductor experiences the force. The magnitude of force is given by F = BIL newton  where F – Force   B – maximum flux density   I – Current   L – Length of conductor

A separately excited d.c. machine is coupled to a 50 Hz, three-phase, 4-pole induction machine as shown in

Description : A separately excited d.c. machine is coupled to a 50 Hz, three-phase, 4-pole induction machine as shown in the figure. The Dc machine is energized first and the machines rotate at 1 600 ... three phase source, the phase sequence being consistent with the direction of rotation. In steady state

Last Answer : A separately excited d.c. machine is coupled to a 50 Hz, three-phase, 4-pole induction machine as shown in the figure. The Dc machine is energized first and the machines rotate at 1 600 1pm. ... rotation. In steady state DC machine acts as a motor and the induction machine acts as a generator  

Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Description : Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Last Answer : Answer: B

Which of the methods listed is used to maintain the division of load between two compound-wound, DC generators operating in parallel? A. The shunt fields are interconnected. B. The shunt field rheostats are interconnected. C. The series fields of both generators are connected in series. D. The equalizer connection parallels the series fields of all machines.

Description : Which of the methods listed is used to maintain the division of load between two compound-wound, DC generators operating in parallel? A. The shunt fields are interconnected. B. The shunt ... generators are connected in series. D. The equalizer connection parallels the series fields of all machines.

Last Answer : Answer: D

Enlist the types of dc machines?

Description : Enlist the types of dc machines?

Last Answer : Answer: D.C. machines are classified into two types 1) separately excited 2) self excited which is further classified into 1)series 2)shunt and 3)compound(which is further classified into cumulative and differential).

Why Does Curving The Pole Faces In A Dc Machines Contributes To A Smoother Dc Output Voltage From It?

Description : Why Does Curving The Pole Faces In A Dc Machines Contributes To A Smoother Dc Output Voltage From It?

Last Answer : For having smoother output voltage from DC machines its commutation must be as ideal as possible. In order to have good commutation the flux density in the air gap must decrease gradually from maximum value under the center of the pole to zero on.

What is the minimum recommended absorption coefficient value for AC and DC rotating machines?

Description : What is the minimum recommended absorption coefficient value for AC and DC rotating machines? 

Last Answer : Tips:  a. IR value decreases some what with an increase I applied voltage. However for machines in good condition substantially the same IR is obtained for any test voltage ... a value which after correction for temperature, may be compared with the recommended minimum value of IR. 

What are the minimum recommended PI values for AC and DC rotating machines?

Description : What are the minimum recommended PI values for AC and DC rotating machines? 

Last Answer : Following minimum recommended PI values criteria is to be followed. a. 1.5 for class – A insulation. b. 2.0 for class – B insulation. c. 2.5 for class – F insulation. 

The introduction of interpoles in between the main poles improves the performance of DC machines because:

Description : The introduction of interpoles in between the main poles improves the performance of DC machines because: (A) the interpole produces additional flux to augment the torque developed (B) the flux waveform ... of the armature is removed (D) a counter emf is induced in the coil undergoing commutation

Last Answer : The introduction of interpoles in between the main poles improves the performance of DC machines because: a counter emf is induced in the coil undergoing commutation

What are the different braking of DC machines?

Last Answer : Dynamic or rheostatic braking,plugging and regenerative braking

What are the different types of DC machines?

Last Answer : Dc machine is classified as   self excited  separately excited  permanent magnet  Self excited Dc motor is further classified as  series ... are classified as  long shunt short shunt

How can I shorten "Add fractional dimension" and still keep its meaning clear?

Description : How can I shorten "Add fractional dimension" and still keep its meaning clear?

Last Answer : How about one box for inches, another box for fractions of an inch? Otherwise you will have to parse e.g. 22 7/8 becomes 22 + (7 divided by 8)

Does anyone know when Fractional Reserve Banking was created?

Description : Does anyone know when Fractional Reserve Banking was created?

Last Answer : Hope this helps. However, I cannot guarantee the accuracy of the content and suggest you find others sources as well.

The cause of fractional atomic weights of elements? -Do You Know?

Description : The cause of fractional atomic weights of elements? -Do You Know?

Last Answer : Atomic masses of most of the elements in atomic mass units involve fractions because atomic mass of an element is the average of relative masses of its various isotopes. While taking average, the result appears as a fraction.

Fractional Gasagu = ?

Description : Fractional Gasagu = ?

Last Answer : Gasagu of fractions = Gasagu of lobes ল Gasagu of logs

What is the fractional index scale ?

Description : What is the fractional index scale ?

Last Answer : When the distances of two places on a map and the distances of those two places on the surface are expressed in the form of fractions , it is called a fractional scale.

The number of solution of the equation `sgn({x})=|1-x|` is/are (where `{*}` represent fractional part function and sgn represent signum function)

Description : The number of solution of the equation `sgn({x})=|1-x|` is/are (where `{*}` represent fractional part function and sgn represent signum function)

Last Answer : The number of solution of the equation `sgn({x})=|1-x|` is/are (where `{*}` represent fractional part function and sgn ... A. `4` B. `3` C. `2` D. `1`