Dark current in light detectors is caused by ∙ a. Thermally generated carriers in the diode ∙ b. The absence of light input ∙ c. Small leakage current ∙ d. Its imperfection

Dark current in light detectors is caused by
∙ a. Thermally generated carriers in the diode  
∙ b. The absence of light input  
∙ c. Small leakage current  
∙ d. Its imperfection
by

1 Answer

Answer :

a. Thermally generated carriers in the diode
by

Related questions

In a PIN diode, leakage current in the absence of light is called: a. baseline current b. zero-point current c. dark current d. E-H current

Description : In a PIN diode, leakage current in the absence of light is called: a. baseline current b. zero-point current c. dark current d. E-H current

Last Answer : c. dark current

The leakage current that flows through a photodiode with no light input ∙ A. dark voltage ∙ B. dark impedance ∙ C. dark power ∙ D. dark current

Description : The leakage current that flows through a photodiode with no light input ∙ A. dark voltage ∙ B. dark impedance ∙ C. dark power ∙ D. dark current

Last Answer : D. dark current

The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode output current to the input optical power ∙ C. the ratio of the input power to output power ∙ D. the ratio of output current to input current

Description : The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode ... . the ratio of the input power to output power ∙ D. the ratio of output current to input current

Last Answer : the ratio of the diode output current to the input optical power

Barrier potential in a P-N junction is caused by (A) Thermally generated electrons and holes. (B) Diffusion of majority carriers across the junction. (C) Migration of minority carriers across the junction. (D) Flow of drift current.

Description : Barrier potential in a P-N junction is caused by (A) Thermally generated electrons and holes. (B) Diffusion of majority carriers across the junction. (C) Migration of minority carriers across the junction. (D) Flow of drift current.

Last Answer : (B) Diffusion of majority carriers across the junction.

A device that was constructed from mirrors and selenium detectors that transmitted sound waves over a beam of light. ∙ A. lightphone ∙ B. photophone ∙ C. cameraphone ∙ D. walletphone

Description : A device that was constructed from mirrors and selenium detectors that transmitted sound waves over a beam of light. ∙ A. lightphone ∙ B. photophone ∙ C. cameraphone ∙ D. walletphone

Last Answer : B. photophone

Optical detectors are square-law devices because they respond to _____ rather than amplitude ∙ a. Intensity ∙ b. Light ∙ c. Density ∙ d. Photon

Description : Optical detectors are square-law devices because they respond to _____ rather than amplitude ∙ a. Intensity ∙ b. Light ∙ c. Density ∙ d. Photon

Last Answer : a. Intensity

One of the following is not a characteristic of light detectors. ∙ a. Responsitivity ∙ b. Spectral response ∙ c. Transmit time ∙ d. Dispersion

Description : One of the following is not a characteristic of light detectors. ∙ a. Responsitivity ∙ b. Spectral response ∙ c. Transmit time ∙ d. Dispersion

Last Answer : ∙ d. Dispersion

The upper pulse rate and information-carrying capacity of a cable is limited by ∙ A. pulse shortening ∙ B. attenuation ∙ C. light leakage ∙ D. modal dispersion

Description : The upper pulse rate and information-carrying capacity of a cable is limited by ∙ A. pulse shortening ∙ B. attenuation ∙ C. light leakage ∙ D. modal dispersion

Last Answer : D. modal dispersion

The upper pulse rate and information carrying capacity of a cable is limited by ∙ a. Pulse shortening ∙ b. Attenuation ∙ c. Light leakage ∙ d. Modal dispersion

Description : The upper pulse rate and information carrying capacity of a cable is limited by ∙ a. Pulse shortening ∙ b. Attenuation ∙ c. Light leakage ∙ d. Modal dispersion

Last Answer : ∙ d. Modal dispersion

In solid-state optical detectors, the excited charge is transported in the solid by ∙ a. Holes and protons ∙ b. Holes and electrons ∙ c. Anion and cation ∙ d. Protons and photons

Description : In solid-state optical detectors, the excited charge is transported in the solid by ∙ a. Holes and protons ∙ b. Holes and electrons ∙ c. Anion and cation ∙ d. Protons and photons

Last Answer : ∙ b. Holes and electrons

What parameter of light detector determines the range or system length that can be achieved for a given wavelength? ∙ a. Transit time ∙ b. Spectral response ∙ c. Dark current ∙ d. Responsitivity

Description : What parameter of light detector determines the range or system length that can be achieved for a given wavelength? ∙ a. Transit time ∙ b. Spectral response ∙ c. Dark current ∙ d. Responsitivity

Last Answer : ∙ b. Spectral response

A pn-junction diode emits light by spontaneous emission ∙ A. LED ∙ B. APD ∙ C. PIN

Description : A pn-junction diode emits light by spontaneous emission ∙ A. LED ∙ B. APD ∙ C. PIN

Last Answer : A. LED

Which of the following is the fastest light sensor? ∙ A. PIN photodiode ∙ B. Photovoltaic diode ∙ C. Photodiode ∙ D. Avalanche photodiode

Description : Which of the following is the fastest light sensor? ∙ A. PIN photodiode ∙ B. Photovoltaic diode ∙ C. Photodiode ∙ D. Avalanche photodiode

Last Answer : Avalanche photodiode

Which of the following is the fastest light sensor? ∙ A. PIN photodiode ∙ B. Photovoltaic diode ∙ C. Photodiode ∙ D. Avalanche photodiode

Description : Which of the following is the fastest light sensor? ∙ A. PIN photodiode ∙ B. Photovoltaic diode ∙ C. Photodiode ∙ D. Avalanche photodiode

Last Answer : D. Avalanche photodiode

Which of the following is the fastest light sensor ∙ a. PIN photodiode ∙ b. Photovoltaic diode ∙ c. Phototransistor ∙ d. Avalanche photodiode

Description : Which of the following is the fastest light sensor ∙ a. PIN photodiode ∙ b. Photovoltaic diode ∙ c. Phototransistor ∙ d. Avalanche photodiode

Last Answer : ∙ d. Avalanche photodiode

Which of the following is NOT a common light detector ∙ a. PIN photodiode ∙ b. Photovoltaic diode ∙ c. Photodiode ∙ d. Avalanche photodiode

Description : Which of the following is NOT a common light detector ∙ a. PIN photodiode ∙ b. Photovoltaic diode ∙ c. Photodiode ∙ d. Avalanche photodiode

Last Answer : ∙ b. Photovoltaic diode

. Is a non-coherent light source foe optical communications system. ∙ a. ILD ∙ b. LED ∙ c. APD ∙ d. PIN Diode

Description : . Is a non-coherent light source foe optical communications system. ∙ a. ILD ∙ b. LED ∙ c. APD ∙ d. PIN Diode

Last Answer : ∙ b. LED

The range of wavelength values that a given photodiode will respond. ∙ A. spectral response ∙ B. permeance ∙ C. dark current ∙ D. reluctance

Description : The range of wavelength values that a given photodiode will respond. ∙ A. spectral response ∙ B. permeance ∙ C. dark current ∙ D. reluctance

Last Answer : A. spectral response

A measure of conversion efficiency of a photodetector. ∙ A. Efficiency ∙ B. Responsivity ∙ C. Dark current ∙ D. Spectral response

Description : A measure of conversion efficiency of a photodetector. ∙ A. Efficiency ∙ B. Responsivity ∙ C. Dark current ∙ D. Spectral response

Last Answer : B. Responsivity

EMD is best described by which statement? ∙ A. 70 percent of the core diameter and 70% of the fiber NA should be filled with light. ∙ B. 70 percent of the fiber diameter and 70% of the cone of acceptance should be filled with light. ∙ C. 70 percent of input light should be measured at the output. ∙ D. 70 percent of the unwanted wavelengths should be attenuated by the fiber.

Description : EMD is best described by which statement? ∙ A. 70 percent of the core diameter and 70% of the fiber NA should be filled with light. ∙ B. 70 percent of the fiber diameter and 70% of the ... be measured at the output. ∙ D. 70 percent of the unwanted wavelengths should be attenuated by the fiber.

Last Answer : 70 percent of the core diameter and 70% of the fiber NA should be filled with light.

Which of the following is used as an optical receiver in fiber optics communications ∙ a. APD ∙ b. Tunnel diode ∙ c. Laser diode ∙ d. LED

Description : Which of the following is used as an optical receiver in fiber optics communications ∙ a. APD ∙ b. Tunnel diode ∙ c. Laser diode ∙ d. LED

Last Answer : a. APD

It is caused by the difference in the propagation time of light rays that take different paths down the fiber. ∙ A. modal dispersion ∙ B. microbending ∙ C. Rayleigh scattering ∙ D. chromatic dispersion

Description : It is caused by the difference in the propagation time of light rays that take different paths down the fiber. ∙ A. modal dispersion ∙ B. microbending ∙ C. Rayleigh scattering ∙ D. chromatic dispersion

Last Answer : A. modal dispersion

It is caused by hydroxide ions in the material ∙ A. visible light absorption ∙ B. infrared absorption ∙ C. ultraviolet absorption ∙ D. ion resonance absorption

Description : It is caused by hydroxide ions in the material ∙ A. visible light absorption ∙ B. infrared absorption ∙ C. ultraviolet absorption ∙ D. ion resonance absorption

Last Answer : D. ion resonance absorption

It is caused by valence electrons in the silica material from which the fiber are manufactured. ∙ A. ion resonance absorption ∙ B. infrared absorption ∙ C. ultraviolet absorption ∙ D. visible light absorption

Description : It is caused by valence electrons in the silica material from which the fiber are manufactured. ∙ A. ion resonance absorption ∙ B. infrared absorption ∙ C. ultraviolet absorption ∙ D. visible light absorption

Last Answer : ultraviolet absorption

______ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. ∙ a. Material dispersion ∙ b. Wavelength dispersion ∙ c. Modal dispersion

Description : ______ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. ∙ a. Material dispersion ∙ b. Wavelength dispersion ∙ c. Modal dispersion

Last Answer : ∙ c. Modal dispersion

Chromatic dispersion can be eliminated by __________. ∙ A. using a monochromatic light source ∙ B. using a very small numerical aperture fiber ∙ C. using a graded-index fiber ∙ D. using a very sensitive photo detector

Description : Chromatic dispersion can be eliminated by __________. ∙ A. using a monochromatic light source ∙ B. using a very small numerical aperture fiber ∙ C. using a graded-index fiber ∙ D. using a very sensitive photo detector

Last Answer : A. using a monochromatic light source

These bends are caused by excessive pressure and tension and generally occur while fiber are bent during handling or installation. ∙ A. microbending ∙ B. macrobending ∙ C. constant-radius bending ∙ D. kinks

Description : These bends are caused by excessive pressure and tension and generally occur while fiber are bent during handling or installation. ∙ A. microbending ∙ B. macrobending ∙ C. constant-radius bending ∙ D. kinks

Last Answer : C. constant-radius bending

Modal dispersion is caused by the ∙ a. Dependence of wavelength on index of refraction ∙ b. Dependence of propagation constant on index of refraction ∙ c. Dependence of the propagation constant on the wavelength ∙ d. Dependence of the propagation constant on the mode number

Description : Modal dispersion is caused by the ∙ a. Dependence of wavelength on index of refraction ∙ b. Dependence of propagation constant on index of refraction ∙ c. Dependence of the propagation constant on the wavelength ∙ d. Dependence of the propagation constant on the mode number

Last Answer : d. Dependence of the propagation constant on the mode number

Material dispersion is caused by the ∙ a. Wavelength dependence of the index of refraction ∙ b. Wavelength independence of the index of refraction ∙ c. Dependence of the propagation constant on the mode number ∙ d. Independence of the propagation constant on the mode number

Description : Material dispersion is caused by the ∙ a. Wavelength dependence of the index of refraction ∙ b. Wavelength independence of the index of refraction ∙ c. Dependence of the propagation constant on the mode number ∙ d. Independence of the propagation constant on the mode number

Last Answer : d. Independence of the propagation constant on the mode number

Band loss is ∙ a. A reduction in transmitter power caused by earth’s surface curvature ∙ b. A reduction in strength of the signal caused by folded dipole bends ∙ c. An attenuation increase caused by bends radiating from the side of the fiber ∙ d. All of these

Description : Band loss is ∙ a. A reduction in transmitter power caused by earth’s surface curvature ∙ b. A reduction in strength of the signal caused by folded dipole bends ∙ c. An attenuation increase caused by bends radiating from the side of the fiber ∙ d. All of these

Last Answer : c. An attenuation increase caused by bends radiating from the side of the fiber

The term dispersion describes the process of ∙ A. separating light into its component frequencies ∙ B. reflecting light from a smooth surface ∙ C. the process by which light is absorbed by an uneven rough surface ∙ D. light scattering

Description : The term dispersion describes the process of ∙ A. separating light into its component frequencies ∙ B. reflecting light from a smooth surface ∙ C. the process by which light is absorbed by an uneven rough surface ∙ D. light scattering

Last Answer : A. separating light into its component frequencies

Dispersion is used to describe the ∙ a. Splitting of white light into its component colors ∙ b. Propagation of light in straight lines ∙ c. Bending of a beam of light when it goes from one medium to another ∙ d. Bending of a beam light when it strikes a mirror

Description : Dispersion is used to describe the ∙ a. Splitting of white light into its component colors ∙ b. Propagation of light in straight lines ∙ c. Bending of a beam of light when it goes from one medium to another ∙ d. Bending of a beam light when it strikes a mirror

Last Answer : a. Splitting of white light into its component colors

Refraction is the ∙ A. bending of light ∙ B. reflection of light waves ∙ C. distortion of light waves ∙ D. diffusion of light waves

Description : Refraction is the ∙ A. bending of light ∙ B. reflection of light waves ∙ C. distortion of light waves ∙ D. diffusion of light waves

Last Answer : A. bending of light

The main benefit of light wave communications over microwaves or any other communications media are ∙ A. lower cost ∙ B. better security ∙ C. wider bandwidth ∙ D. freedom from interface

Description : The main benefit of light wave communications over microwaves or any other communications media are ∙ A. lower cost ∙ B. better security ∙ C. wider bandwidth ∙ D. freedom from interface

Last Answer : C. wider bandwidth

The speed of light in plastic compared to the speed of light in air is ∙ A. less ∙ B. more ∙ C. the same ∙ D. zero

Description : The speed of light in plastic compared to the speed of light in air is ∙ A. less ∙ B. more ∙ C. the same ∙ D. zero

Last Answer : A. less

Total internal reflection takes place if the light ray strikes the interface at an angle with what relationship to the critical angle? ∙ A. less than ∙ B. greater than ∙ C. equal to ∙ D. zero

Description : Total internal reflection takes place if the light ray strikes the interface at an angle with what relationship to the critical angle? ∙ A. less than ∙ B. greater than ∙ C. equal to ∙ D. zero

Last Answer : ∙ B. greater than

A popular light wavelength fiber-optic cable is ∙ A. 0.7 micrometer ∙ B. 1.3 micrometer ∙ C. 1.5 micrometer ∙ D. 1.8 micrometer

Description : A popular light wavelength fiber-optic cable is ∙ A. 0.7 micrometer ∙ B. 1.3 micrometer ∙ C. 1.5 micrometer ∙ D. 1.8 micrometer

Last Answer : B. 1.3 micrometer

The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Description : The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Last Answer : B. light sensitivity

The time it takes a light induced carrier travel across the depletion region of the semiconductor. ∙ A. dispersion ∙ B. response time ∙ C. irradiance ∙ D. transit time

Description : The time it takes a light induced carrier travel across the depletion region of the semiconductor. ∙ A. dispersion ∙ B. response time ∙ C. irradiance ∙ D. transit time

Last Answer : D. transit time

How can modal dispersion reduced entirely? ∙ A. Use a graded index fiber ∙ B. Use a single-mode fiber ∙ C. Use a monochromatic light source ∙ D. Use a very sensitive light detector

Description : How can modal dispersion reduced entirely? ∙ A. Use a graded index fiber ∙ B. Use a single-mode fiber ∙ C. Use a monochromatic light source ∙ D. Use a very sensitive light detector

Last Answer : Use a single-mode fiber

As light is coupled in a multiport deflective device, the power is reduced by ∙ A. 1.5 dB ∙ B. 0.1 dB ∙ C. 0.5 dB ∙ D. 0.001 dB

Description : As light is coupled in a multiport deflective device, the power is reduced by ∙ A. 1.5 dB ∙ B. 0.1 dB ∙ C. 0.5 dB ∙ D. 0.001 dB

Last Answer : C. 0.5 dB

Light rays that are emitted simultaneously from an LED and propagated down an optical fiber do not arrive at the far end of the fiber at the same time results to ∙ A. intramodal dispersion ∙ B. pulse length dispersion ∙ C. modal dispersion ∙ D. wavelength dispersion

Description : Light rays that are emitted simultaneously from an LED and propagated down an optical fiber do not arrive at the far end of the fiber at the same time results to ∙ A. intramodal dispersion ∙ B. pulse length dispersion ∙ C. modal dispersion ∙ D. wavelength dispersion

Last Answer : D. wavelength dispersion

For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Description : For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Last Answer : ∙ C. -35 dBm

t is a result of photons of light that are absorbed by the atoms of the glass core molecule. ∙ A. ion resonance absorption ∙ B. infrared absorption ∙ C. ultraviolet absorption ∙ D. visible light absorption

Description : t is a result of photons of light that are absorbed by the atoms of the glass core molecule. ∙ A. ion resonance absorption ∙ B. infrared absorption ∙ C. ultraviolet absorption ∙ D. visible light absorption

Last Answer : B. infrared absorption

It is analogous to power dissipation to copper cables, impurities in the fiber absorb the light and covert it to heat. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Description : It is analogous to power dissipation to copper cables, impurities in the fiber absorb the light and covert it to heat. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Last Answer : B. absorption loss

Which of the following is not a factor in cable light loss? ∙ A. reflection ∙ B. absorption ∙ C. scattering ∙ D. dispersion

Description : Which of the following is not a factor in cable light loss? ∙ A. reflection ∙ B. absorption ∙ C. scattering ∙ D. dispersion

Last Answer : A. reflection

Results in reduction in the power of light wave as it travels down the cable. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Description : Results in reduction in the power of light wave as it travels down the cable. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Last Answer : A. power loss

Infrared light has a wavelength that is ∙ A. less than 400 nm ∙ B. more than 700 nm ∙ C. less than 700 nm ∙ D. a little over 400 nm

Description : Infrared light has a wavelength that is ∙ A. less than 400 nm ∙ B. more than 700 nm ∙ C. less than 700 nm ∙ D. a little over 400 nm

Last Answer : B. more than 700 nm

More than one path for light rays to take down the fiber ∙ A. Multimode ∙ B. Step-index ∙ C. Single mode

Description : More than one path for light rays to take down the fiber ∙ A. Multimode ∙ B. Step-index ∙ C. Single mode

Last Answer : A. Multimode