Description : The _____ is equal to the number of electrons emitted per second times the electron charge ∙ a. Intensity ∙ b. Optical power ∙ c. Photocurrent ∙ d. Responsitivity
Last Answer : c. Photocurrent
Description : In solid-state optical detectors, the excited charge is transported in the solid by ∙ a. Holes and protons ∙ b. Holes and electrons ∙ c. Anion and cation ∙ d. Protons and photons
Last Answer : ∙ b. Holes and electrons
Description : The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode ... . the ratio of the input power to output power ∙ D. the ratio of output current to input current
Last Answer : the ratio of the diode output current to the input optical power
Description : The law that states “When visible light of high frequency electromagnetic radiation illuminates a metallic surface, electrons are emitted” is known as ____________. ∙ A. Einstein law of photon ∙ B. Marconi’s law ∙ C. Maxwell’s law ∙ D. Plank’s law
Last Answer : D. Plank’s law
Description : An increase in light intensity produces fast optic switching due to ∙ a. Increase in index of glass ∙ b. Amplification of optical signal ∙ c. High gain ∙ d. Photoconductivity
Last Answer : b. Amplification of optical signal
Description : The _____ of a detector is the fraction of incident photons that produce a photoelectron or electron-hole pair ∙ a. Responsitivity ∙ b. Photon efficiency ∙ c. Aperture ∙ d. Quantum efficiency
Last Answer : d. Quantum efficiency
Description : Light intensity is generally described in terms of __________ and measured in _________. ∙ A. Luminous flux density; Lumens per unit area ∙ B. Luminous flux intensity; Lumens per unit area ∙ C. Luminous flux density; Lumens per unit volume ∙ D. Luminous flux intensity; Lumens per unit volume
Last Answer : Luminous flux density; Lumens per unit area
Description : A device that was constructed from mirrors and selenium detectors that transmitted sound waves over a beam of light. ∙ A. lightphone ∙ B. photophone ∙ C. cameraphone ∙ D. walletphone
Last Answer : B. photophone
Description : One of the following is not a characteristic of light detectors. ∙ a. Responsitivity ∙ b. Spectral response ∙ c. Transmit time ∙ d. Dispersion
Last Answer : ∙ d. Dispersion
Description : Dark current in light detectors is caused by ∙ a. Thermally generated carriers in the diode ∙ b. The absence of light input ∙ c. Small leakage current ∙ d. Its imperfection
Last Answer : a. Thermally generated carriers in the diode
Description : Which modulation methods are the most widely used in optical systems? ∙ a. Phase and frequency modulations ∙ b. Polarization modulation and phase modulation ∙ c. Intensity modulation and phase modulation ∙ d. Intensity modulation and polarization modulation
Last Answer : Intensity modulation and polarization modulation
Description : Which of the following terms best describes the reason that light is refracted at different angles? ∙ A. Photon energy changes with wavelength ∙ B. Light is refracted as a function of surface smoothness ∙ ... determined partly by a and b ∙ D. The angle is determined by the index of the materials
Last Answer : ∙ D. The angle is determined by the index of the materials
Description : Light traveling in optical fiber follows which of the following principles. ∙ a. Huygen’s principle ∙ b. Reflection theory ∙ c. Light theory ∙ d. Snell’s law
Last Answer : d. Snell’s law
Description : Optical fibers for telecommunications are typically about _____ mils thick and consists of a glass core, a glass cladding of lower index of refraction, and a protective coating ∙ a. 5 ∙ b. 6 ∙ c. 7 ∙ d. 8
Last Answer : ∙ a. 5
Description : The graded-index multimode optical fiber has a core diameter of _____ nm. ∙ a. 0.5 ∙ b. 0.05 ∙ c. 0.0005 ∙ d. 5
Last Answer : ∙ a. 0.5
Description : A step-index multimode optical fiber has a core diameter of _____ nm. ∙ a. 0.02 ∙ b. 0.2 ∙ c. 2 ∙ d. 0.002
Last Answer : b. 0.2
Description : A single mode optical fiber has a core diameter of _____ nm. ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.2 ∙ d. 0.05
Last Answer : a. 0.1
Description : The energy of the photon is ∙ a. Directly proportional to its bandwidth ∙ b. Directly proportional to the Planck’s constant ∙ c. Directly proportional to Boltzmann’s constant ∙ d. Inversely proportional to the Planck’s constant
Last Answer : Directly proportional to the Planck’s constant
Description : What is the photon energy for an infrared wave with frequency of 1012 Hz? ∙ a. 10.6 x 1034 joules ∙ b. 6.63 x 10-34 joules ∙ c. 6.63 x 10-22 joules ∙ d. 10.6 x 1022 joules
Last Answer : ∙ c. 6.63 x 10-22 joules
Description : The band of light frequencies to which human eye will respond ∙ A. Infrared ∙ B. Visible light ∙ C. Ultraviolet ∙ D. Cosmic ray
Last Answer : B. Visible light
Description : The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination
Last Answer : B. light sensitivity
Description : Light rays that are emitted simultaneously from an LED and propagated down an optical fiber do not arrive at the far end of the fiber at the same time results to ∙ A. intramodal dispersion ∙ B. pulse length dispersion ∙ C. modal dispersion ∙ D. wavelength dispersion
Last Answer : D. wavelength dispersion
Description : For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm
Last Answer : ∙ C. -35 dBm
Description : It is described as the flow of light energy past a given point in a specified time ∙ A. Optical radiation ∙ B. Optical impedance ∙ C. Optical illusion ∙ D. Optical power
Last Answer : D. Optical power
Description : In radiometric terms, it measures the rate at which electromagnetic waves transfer light energy ∙ A. Optical radiation ∙ B. Optical impedance ∙ C. Optical illusion ∙ D. Optical power
Description : Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber
Last Answer : b. Light power out of a fiber
Last Answer : ∙ b. Light power out of a fiber
Description : Which of the following contributes to the broadening of laser emission bandwidth? ∙ a. Doppler shift of moving atoms and molecules ∙ b. Amplification within the laser medium ∙ c. Coherence of the laser light ∙ d. Optical pumping of the laser transition
Last Answer : Doppler shift of moving atoms and molecules
Description : . Is a non-coherent light source foe optical communications system. ∙ a. ILD ∙ b. LED ∙ c. APD ∙ d. PIN Diode
Last Answer : ∙ b. LED
Description : What is a specific path the light takes in an optical fiber corresponding to a certain angle and number of reflection ∙ a. Mode ∙ b. Grade ∙ c. Numerical Aperture ∙ d. Dispersion
Last Answer : a. Mode
Description : Is the different angle of entry of light into an optical fiber when the diameter of the core is many times the wavelength of the light transmitted. ∙ a. Acceptance angle ∙ b. Modes ∙ c. Sensors ∙ d. Aperture
Last Answer : b. Modes
Description : The range of wavelength values that a given photodiode will respond. ∙ A. spectral response ∙ B. permeance ∙ C. dark current ∙ D. reluctance
Last Answer : A. spectral response
Description : The core of an optical fiber has a ∙ a. Lower refracted index than air ∙ b. Lower refractive index than the cladding ∙ c. Higher refractive index than the cladding ∙ d. Similar refractive index with the cladding
Last Answer : c. Higher refractive index than the cladding
Description : What is used to block light from a laser and let other light through ∙ a. Neutral density ∙ b. Color ∙ c. Interference ∙ d. Spatial
Last Answer : ∙ c. Interference
Description : Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch
Last Answer : . dB/km
Description : Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch
Last Answer : ∙ b. dB/km
Description : Which of the following is not a part of the optical spectrum? ∙ A. infrared ∙ B. ultraviolet ∙ C. visible color ∙ D. x-rays
Last Answer : ∙ D. x-rays
Description : For a 300-m optical fiber cable with a bandwidth distance product of 600 MHz-km, determine the bandwidth. ∙ A. 5 GHz ∙ B. 1 GHz ∙ C. 2 GHz
Last Answer : C. 2 GHz
Description : A type of index of an optical fiber that has no cladding and whose central core has a non-uniform refractive index. ∙ A. graded index ∙ B. multimode ∙ C. single mode ∙ D. step-index
Last Answer : ∙ A. graded index
Description : A type of index profile of an optical fiber that has a central core and outside cladding with a uniform refractive index ∙ A. multimode ∙ B. graded index ∙ C. step-index ∙ D. single mode
Last Answer : ∙ C. step-index
Description : The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector
Last Answer : B. the source, the link and the receiver
Description : Optical power is sometimes called __________. ∙ A. Radiant emission ∙ B. Radiant power ∙ C. Radiant flux ∙ D. Radiant optics
Last Answer : C. Radiant flux
Description : Developed an optical fiber with losses less that 2 dB/km ∙ A. Kao and Bockham ∙ B. Maiman, Kao and Bockham ∙ C. Maiman and Schawlow ∙ D. Kapron, Keck and Maurer
Last Answer : ∙ A. Kao and Bockham
Description : The scientist who built the first optical maser ∙ A. Charles Townes ∙ B. GA Bockham ∙ C. Theodore Maiman ∙ D. ACS Van Heel
Last Answer : ∙ C. Theodore Maiman
Description : Approximately what is the frequency limit of the optical fiber? ∙ A. 20 MHz ∙ B. 1 MHz ∙ C. 100 MHz ∙ D. 40 GHz
Last Answer : ∙ D. 40 GHz
Description : Used to test a fiber optics splice ∙ a. Spectrum analyzer ∙ b. Oscilloscope ∙ c. Optical power meter ∙ d. Field strength meter
Last Answer : c. Optical power meter
Description : What is the frequency limit of an optical fiber? ∙ a. 20 GHz ∙ b. 30 GHz ∙ c. 40 GHz ∙ d. 50 GHz
Last Answer : ∙ c. 40 GHz
Description : Which optical detector is used when high sensitivity and bandwidth are required? ∙ a. PMT ∙ b. APD ∙ c. PIN ∙ d. Phototransistor
Last Answer : a. PMT
Description : One of the following is not a solid-state optical detector ∙ a. APD ∙ b. PIN ∙ c. PMT ∙ d. Phototransistors
Last Answer : . PMT
Description : An IC that represents a short distance one-way optical communications ∙ a. Optoisolator ∙ b. Insulator ∙ c. Multivibrator ∙ d. Optical IC
Last Answer : a. Optoisolator