Description : What type of klystron is used as the final stage of a power- amplifier transmitter?
Last Answer : Multicavity klystron.
Description : In an AM transmitter with 100% modulation, the voltage of the final RF stage will be
Last Answer : approximately four times the DC supply voltage
Last Answer : Antenna-to-ground capacitance can cause the oscillator frequency to vary.
Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A
Last Answer : D. 2.0 A
Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line
Last Answer : A. Through installing a band-pass filter in the antenna feed line
Description : The final power amplifier in an FM transmitter usually operates class ______. A. AB B. C C. B D. A
Last Answer : B. C
Description : The final amplifier of either FM or AM transmitter operates as A. Class B B. Class C C. Class A D. Class D
Last Answer : B. Class C
Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna
Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna
Description : The final power amplifier in an FM transmitter usually operates class ___
Last Answer : C
Description : The final power amplifier in an FM transmitter usually operates class ______.
Description : What precaution should you take when substituting a synchro tester in a circuit for a transmitter?
Last Answer : Use only one receiver so as not to overload the tester.
Description : What is the most likely problem if the transmitter shaft reads 0º when the receiver shaft indicates 180º?
Last Answer : The rotor leads on either the transmitter or the receiver are reversed.
Description : What is the relationship between the transmitter and receiver stator voltages when their rotors are in correspondence?
Last Answer : The voltages are equal and oppose each other.
Description : What is the physical difference between a synchro transmitter and a synchro receiver?
Last Answer : A synchro receiver uses some form of damping to retard excessive oscillations or spinning.
Description : Describe the zero-position of a synchro transmitter.
Last Answer : The transmitter is in its zero-position when the rotor is aligned with the S2 stator winding.
Description : What unit of measurement refers to the torque of a synchro transmitter
Last Answer : Ounce-inches.
Description : What are some disadvantages of operating a transmitter at or near the muf?
Last Answer : Frequent signal fading and dropouts.
Description : What are three ways of controlling the amount of transmitter-generated emi?
Last Answer : (a) filtering and shielding of the transmitter (b) limiting bandwidth (c) cutting the antenna to the
Description : Transmitter power readings are most often referenced to what power level?
Last Answer : 1 milliwatt.
Description : Where should the transmitter spectrum be located with respect to the receiver response curve?
Last Answer : In the center.
Description : The spectrum of a radar transmitter describes what characteristic of the output pulse?
Last Answer : Frequency distribution
Description : Immediately after the transmitter fires, stc reduces the receiver gain to what level?
Last Answer : Zero.
Description : What controls transmitter pulse width?
Last Answer : The modulator.
Description : What transmitter component allows the radiation of a large number of discrete frequencies over a wide band?
Last Answer : . Frequency synthesizer.
Description : In an externally synchronized radar, what determines the prr of the transmitter?
Last Answer : The master oscillator.
Description : What transmission method uses a stable cw reference oscillator, which is locked in phase with the transmitter frequency?
Last Answer : Pulse-Doppler.
Description : What factor determines the difference between the transmitted frequency and the received frequency in an fm transmitter?
Last Answer : Travel time.
Description : The beat frequency in a swept-frequency transmitter provides what contact information?
Last Answer : Range.
Description : When a transmitter uses a high-power oscillator to produce the output pulse, what switches the oscillator on and off?
Last Answer : High-voltage pulse from the modulator.
Description : What type of radar transmitter power is measured over a period of time?
Last Answer : Average power.
Description : What vswr is a perfect match between a transmitter and its load?
Last Answer : 1 to 1.
Description : What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?
Last Answer : High vswr, which equates to poor reception or a loss of power output.
Description : All the power sent down a transmission line from a transmitter can be transferred to an antenna under what optimum conditions?
Last Answer : When the characteristic impedance of the transmission line and the load impedance are equal.
Description : What term is used for the end of the transmission line that is connected to a transmitter?
Last Answer : Input end, generator end, transmitter end, sending end, and source.
Description : What connecting link is used to transfer energy from a radio transmitter to its antenna located on
Last Answer : Transmission line.
Description : List five common fiber optic transmitter packages.
Last Answer : TO can, DIP, butterfly lead microcircuits, circuit cards, and stand-alone optical fiber converters.
Description : Which part of a fiber optic transmitter converts the processed electrical signal to an optical signal?
Last Answer : The optical source.
Description : What are the three parts of a fiber optic transmitter?
Last Answer : Interface circuit, source drive circuit, and an optical source.
Description : What is the range of earth terminal transmitter output power?
Last Answer : Up to 20 kilowatts.
Description : In an fm transmitter, when does an oscillator generate only a steady frequency?
Last Answer : When no modulation is present.
Description : What purpose does a microphone perform in an AM transmitter?
Last Answer : It converts audio (sound) into electrical energy.
Description : What is the function of the oscillator in a cw transmitter?
Last Answer : It generates an rf carrier at a given frequency within required limits.
Description : What are the four basic transmitter types?
Last Answer : Am, fm, cw, ssb.
Description : A step transmitter is a modification of what electrical device?
Last Answer : Rotary switch.
Description : What are the transmitter operating modes?
Last Answer : Lsb, usb, isb, AM, cw, fsk.
Description : What capability does a transmitter transfer switchboard provide?
Last Answer : Transferring remote control functions and signals to transmitters.
Description : What are the two major sections of a typical AM transmitter?
Last Answer : Rf and af units.
Description : What is the purpose of frequency-multiplier stages in a VHF transmitter?
Last Answer : To raise the low frequency of a stable oscillator to the vhf range.