Description : What term is used for the end of the transmission line that is connected to an antenna?
Last Answer : Output end, receiving end, load end and sink.
Description : Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line
Last Answer : D. load connected to the output end of a transmission line
Description : What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?
Last Answer : High vswr, which equates to poor reception or a loss of power output.
Description : All the power sent down a transmission line from a transmitter can be transferred to an antenna under what optimum conditions?
Last Answer : When the characteristic impedance of the transmission line and the load impedance are equal.
Description : What transmission method uses a stable cw reference oscillator, which is locked in phase with the transmitter frequency?
Last Answer : Pulse-Doppler.
Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts
Last Answer : D. 6 watts
Description : What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?
Last Answer : Pulse width
Last Answer : Pulse width.
Description : On an open-ended transmission line, the voltage is always zero at what distance from each end of the line?
Last Answer : One-fourth the distance from each end of the line.
Description : To measure incident power, you must rotate the coupler detector of the wattmeter so that the arrow indicating power flow points toward which end of the transmission line?
Last Answer : Load.
Description : What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%
Last Answer : D. Efficiency = radiation resistance/total resistance x 100%
Description : It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter
Last Answer : A. when comparing the gains of directional antennas
Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter
Last Answer : A. When comparing the gains of directional antennas
Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power
Last Answer : C. Mean power
Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power
Last Answer : A. Carrier power
Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power
Last Answer : C. Carrier power
Description : A device that radiates electromagnetic energy and or intercepts electromagnetic radation. A. Antenna B. Transmitter C. Transmission line D. Transceiver
Last Answer : A. Antenna
Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna
Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna
Description : Why are shunt reactors connected at the receiving end of long transmission line system: (1) To increase the terminal voltage (2) To compensate voltage rise caused by capacitive charging at light load (3) To improve power factor (4) None of these
Last Answer : Why are shunt reactors connected at the receiving end of long transmission line system: To compensate voltage rise caused by capacitive charging at light load
Description : What precaution should you take when substituting a synchro tester in a circuit for a transmitter?
Last Answer : Use only one receiver so as not to overload the tester.
Description : What is the most likely problem if the transmitter shaft reads 0º when the receiver shaft indicates 180º?
Last Answer : The rotor leads on either the transmitter or the receiver are reversed.
Description : What is the relationship between the transmitter and receiver stator voltages when their rotors are in correspondence?
Last Answer : The voltages are equal and oppose each other.
Description : What is the physical difference between a synchro transmitter and a synchro receiver?
Last Answer : A synchro receiver uses some form of damping to retard excessive oscillations or spinning.
Description : Describe the zero-position of a synchro transmitter.
Last Answer : The transmitter is in its zero-position when the rotor is aligned with the S2 stator winding.
Description : What unit of measurement refers to the torque of a synchro transmitter
Last Answer : Ounce-inches.
Description : What are some disadvantages of operating a transmitter at or near the muf?
Last Answer : Frequent signal fading and dropouts.
Description : What are three ways of controlling the amount of transmitter-generated emi?
Last Answer : (a) filtering and shielding of the transmitter (b) limiting bandwidth (c) cutting the antenna to the
Description : Transmitter power readings are most often referenced to what power level?
Last Answer : 1 milliwatt.
Description : Where should the transmitter spectrum be located with respect to the receiver response curve?
Last Answer : In the center.
Description : The spectrum of a radar transmitter describes what characteristic of the output pulse?
Last Answer : Frequency distribution
Description : Immediately after the transmitter fires, stc reduces the receiver gain to what level?
Last Answer : Zero.
Description : What type of klystron is used as the final stage of a power- amplifier transmitter?
Last Answer : Multicavity klystron.
Description : What controls transmitter pulse width?
Last Answer : The modulator.
Description : What transmitter component allows the radiation of a large number of discrete frequencies over a wide band?
Last Answer : . Frequency synthesizer.
Description : In an externally synchronized radar, what determines the prr of the transmitter?
Last Answer : The master oscillator.
Description : What factor determines the difference between the transmitted frequency and the received frequency in an fm transmitter?
Last Answer : Travel time.
Description : The beat frequency in a swept-frequency transmitter provides what contact information?
Last Answer : Range.
Description : When a transmitter uses a high-power oscillator to produce the output pulse, what switches the oscillator on and off?
Last Answer : High-voltage pulse from the modulator.
Description : What type of radar transmitter power is measured over a period of time?
Last Answer : Average power.
Description : What vswr is a perfect match between a transmitter and its load?
Last Answer : 1 to 1.
Description : What connecting link is used to transfer energy from a radio transmitter to its antenna located on
Last Answer : Transmission line.
Description : List five common fiber optic transmitter packages.
Last Answer : TO can, DIP, butterfly lead microcircuits, circuit cards, and stand-alone optical fiber converters.
Description : Which part of a fiber optic transmitter converts the processed electrical signal to an optical signal?
Last Answer : The optical source.
Description : What are the three parts of a fiber optic transmitter?
Last Answer : Interface circuit, source drive circuit, and an optical source.
Description : What is the range of earth terminal transmitter output power?
Last Answer : Up to 20 kilowatts.
Description : In an fm transmitter, when does an oscillator generate only a steady frequency?
Last Answer : When no modulation is present.
Description : What purpose does a microphone perform in an AM transmitter?
Last Answer : It converts audio (sound) into electrical energy.
Description : What is the final stage of a transmitter?
Last Answer : Power amplifier.