In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?

In a nondegenerative parametric amplifier the difference  between the input frequency and the pump frequency is called  what?
by

1 Answer

Answer :

Idler- or lower-sideband frequency.
by

Related questions

What is the primary difference between the pump signal of a simple parametric amplifier and the pump signal of a nondegenerative parametric amplifier?

Description : What is the primary difference between the pump signal of a simple parametric amplifier and the pump signal of a nondegenerative parametric amplifier?

Last Answer : The pump signal of a nondegenerative parametric amplifier is higher than twice the input signal.

The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Last Answer : Exactly double the input frequency.

What is the purpose of the pump in a parametric amplifier?

Description : What is the purpose of the pump in a parametric amplifier?

Last Answer : Supplies the electrical energy required to vary the capacitance.

What is the most important feature of the parametric amplifier?

Description : What is the most important feature of the parametric amplifier?

Last Answer : The low-noise characteristic.

The underlying principle of operation of the parametric amplifier is based on what property?

Description : The underlying principle of operation of the parametric amplifier is based on what property?

Last Answer : Reactance.

What is the output frequency of an upper-sideband parametric-frequency converter?

Description : What is the output frequency of an upper-sideband parametric-frequency converter?

Last Answer : The sum of the input frequency and the pump frequency.

If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Last Answer : . A different shape than the input signals but larger in amplitude.

If only one input signal is used with a difference amplifier, what will the output signal be?

Description : If only one input signal is used with a difference amplifier, what will the output signal be?

Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.

If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than

. If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Last Answer : No output (the signals will "cancel out").

What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?

Description : What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?

Last Answer : Common emitter (CE) and common base (CB)

What components form the input-signal-developing impedance for the amplifier?

Description : What components form the input-signal-developing impedance for the amplifier?

Last Answer : C2 and the secondary of T1.

If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Description : If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Last Answer : The gain increases.

In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?

Description : In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?

Last Answer : The signals are opposite in polarity or 180 degrees out of phase with each other.

The input and output signals of a JFET amplifier have what phase relationship?

Description : The input and output signals of a JFET amplifier have what phase relationship?

Last Answer : They are 180 degrees out of phase.

What is used to bias a magnetic amplifier so that the control winding remains free to accept control (input) signals?

Description : What is used to bias a magnetic amplifier so that the control winding remains free to accept control (input) signals?

Last Answer : A bias winding and associated circuitry.

In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Last Answer : 0 volts.

If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Last Answer : 200 millivolts. A-18. a. Differential amplifier

If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?

Description : If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?

Last Answer : Each output will be a sine wave with a peak-to-peak amplitude of 100 millivolts. The output signals will be 180 degrees out of phase with each other.

If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?

Description : If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?

Last Answer : 800 watts.

Does an amplifier actually change an input signal? Why or why not?

Description : Does an amplifier actually change an input signal? Why or why not?

Last Answer : No, the input signal is unchanged, the output signal is controlled by the input signal but does not effect the actual input signal.

Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?

Description : Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?

Last Answer : Yes.

What is the purpose of a frequency-determining network in an rf amplifier?

Description : What is the purpose of a frequency-determining network in an rf amplifier?

Last Answer : To provide maximum impedance at the desired frequency.

What component in an amplifier circuit tends to limit the low-frequency response of the amplifier?

Description : What component in an amplifier circuit tends to limit the low-frequency response of the amplifier?

Last Answer : The coupling capacitor (C3).

What components can be used to increase the high frequency response of an amplifier?

Description : What compone What components What components can be used to increase the high frequency response of an amplifier?

Last Answer : Peaking coils.

What is the major factor that limits the high-frequency response of an amplifier circuits?

Description : What is the major factor that limits the high-frequency response of an amplifier circuits?

Last Answer : The capacitance of the circuit.

What are the factors that limit the frequency response of a transistor amplifier?

Description : What are the factors that limit the frequency response of a transistor amplifier?

Last Answer : The capacitance and inductance of the circuit and the interelectrode capacitance of the transistor.

What are the upper and lower frequency limits of an amplifier?

Description : What are the upper and lower frequency limits of an amplifier?

Last Answer : The half-power points of a frequency-response curve. The upper and lower limits of the band f frequencies for which the amplifier is most effective.

What is the frequency classification of a magnetic amplifier

Description : What is the frequency classification of a magnetic amplifier

Last Answer : An audio (or low) frequency power amplifier.

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is

Description : An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C

Last Answer : An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C 18.2 microvolt

What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Description : What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Last Answer : 120 hertz.

Is better filtering achieved at a high frequency or at a low frequency at the input of the filter?

Description : Is better filtering achieved at a high frequency or at a low frequency at the input of the filter?

Last Answer : High

What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Description : What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Last Answer : 120 hertz.

What is the Ripple frequency of a half-wave rectifier if the input frequency is 60 Hz?

Description : What is the Ripple frequency of a half-wave rectifier if the input frequency is 60 Hz?

Last Answer : 60 hertz.

When measuring harmonic distortion, you set the signal generator to input a 15-kHz test signal. To what frequency should you set the wave analyzer?

Description : When measuring harmonic distortion, you set the signal generator to input a 15-kHz test signal. To what frequency should you set the wave analyzer?

Last Answer : 45 kHz.

Can a difference amplifier have more than two inputs?

Description : Can a difference amplifier have more than two inputs?

Last Answer : No

What is the difference between a subtractor and a difference amplifier?

Description : What is the difference between a subtractor and a difference amplifier?

Last Answer : . The difference amplifier multiplies the difference between the two inputs by the gain of the circuit while the subtractor merely subtracts one input signal from the other

What is the difference between a summing amplifier and an adder circuit?

Description : What is the difference between a summing amplifier and an adder circuit?

Last Answer : The adder simply adds the input signals together while the summing amplifier multiplies the sum of the input signals by the gain of circuit.

In inverting amplifier, the phase difference between input and output voltages must be A. 30° B. 45° C. 90° D. 180°

Description : In inverting amplifier, the phase difference between input and output voltages must be A. 30° B. 45° C. 90° D. 180°

Last Answer : 180°

For non-inverting amplifier the input and output is A. out of phase B. in phase C. have phase difference of 180° D. have phase difference of 90°

Description : For non-inverting amplifier the input and output is A. out of phase B. in phase C. have phase difference of 180° D. have phase difference of 90°

Last Answer : in phase

……… are also called as parametric subroutines a.Micro b.Macro c.Sub Macro d.Sub Micro

Description : ……… are also called as parametric subroutines a.Micro b.Macro c.Sub Macro d.Sub Micro

Last Answer : b.Macro

Where online can I learn about parametric functions?

Description : Where online can I learn about parametric functions?

Last Answer : http://www.tutorvista.com/math/study-types-of-differentiation

Which of the following is not a method to describe a curve mathematically? a.Explicit form b.Laplace form c.Implicit form d.Parametric form

Description : Which of the following is not a method to describe a curve mathematically? a.Explicit form b.Laplace form c.Implicit form d.Parametric form

Last Answer : b.Laplace form

Find parametric equation for Y-coordinates of Hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.2u3-3u2+2u+4 b.3u3-2u2-2u-4 c.2u3-3u2-2u-4 d.2u3+3u2+2u+4

Description : Find parametric equation for Y-coordinates of Hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.2u3-3u2+2u+4 b.3u3-2u2-2u-4 c.2u3-3u2-2u-4 d.2u3+3u2+2u+4

Last Answer : a.2u3-3u2+2u+4

Find parametric equation for X-coordinates of hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.-5u3+8u2+u+1 b.5u3+8u2+u+1 c.8u3-5u2-u+1 d.8u3+5u2+u+1

Description : Find parametric equation for X-coordinates of hermite cubic spline curve having endpoints P0[4,4]; P1[8,5] a.-5u3+8u2+u+1 b.5u3+8u2+u+1 c.8u3-5u2-u+1 d.8u3+5u2+u+1

Last Answer : a.-5u3+8u2+u+1

Parametric equation for circle a.X=x+Rcosu; Y=y+Rsinu; Z=z b.X=Rcosu; Y=Rsinu; Z=z c.X=x+Rsinu; Y=y+Rcosu; Z=z d.X=Rsinu; Y=y+Rcosu; Z=z

Description : Parametric equation for circle a.X=x+Rcosu; Y=y+Rsinu; Z=z b.X=Rcosu; Y=Rsinu; Z=z c.X=x+Rsinu; Y=y+Rcosu; Z=z d.X=Rsinu; Y=y+Rcosu; Z=z

Last Answer : a.X=x+Rcosu; Y=y+Rsinu; Z=z

Two lines L1 and L2 having Parametric equations are P1=[3 4 7]+u[2 2 -6] and P2=[15 -2]+u[1 4 2]. Tangent vector for line L1 a.2i+2j-6k b.2i+2j+6k c.2i-2j-6k d.6-2j-2k

Description : Two lines L1 and L2 having Parametric equations are P1=[3 4 7]+u[2 2 -6] and P2=[15 -2]+u[1 4 2]. Tangent vector for line L1 a.2i+2j-6k b.2i+2j+6k c.2i-2j-6k d.6-2j-2k

Last Answer : a.2i+2j-6k

Write parametric equation of line having end points P1(3,5,8) and P2 (6,4,3). a.[3 5 8]+u[3 -1 -5] b.[3 5 8]+u[3 1 5] c.[3 8 5]+u[3 -1 -5] d.[3 5 8]+u[-3 1 5]

Description : Write parametric equation of line having end points P1(3,5,8) and P2 (6,4,3). a.[3 5 8]+u[3 -1 -5] b.[3 5 8]+u[3 1 5] c.[3 8 5]+u[3 -1 -5] d.[3 5 8]+u[-3 1 5]

Last Answer : a.[3 5 8]+u[3 -1 -5]

What is a parametric test ?

Description : What is a parametric test ?

Last Answer : In this case, the value of the aggregate parameter is assumed to be a value of aggregate parameters. Later it is checked whether the conjecture is true or false. This method of verifying hypotheses is called ... tests in the parametric test are Z test , T test , Ky -square test and F test.