Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?
Last Answer : 200 millivolts. A-18. a. Differential amplifier
Description : How many inputs and outputs are possible with a differential amplifier?
Last Answer : Two inputs, two outputs.
Description : In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?
Last Answer : The signals are opposite in polarity or 180 degrees out of phase with each other.
Description : The input and output signals of a JFET amplifier have what phase relationship?
Last Answer : They are 180 degrees out of phase.
Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?
Last Answer : . A different shape than the input signals but larger in amplitude.
Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?
Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than
Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?
Last Answer : No output (the signals will "cancel out").
Description : What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?
Last Answer : Common emitter (CE) and common base (CB)
Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages
Last Answer : Answer: C
Description : To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp
Last Answer : Answer: D
Description : What is used to bias a magnetic amplifier so that the control winding remains free to accept control (input) signals?
Last Answer : A bias winding and associated circuitry.
Description : In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?
Last Answer : Local oscillator and coherent oscillator.
Description : If only one input signal is used with a difference amplifier, what will the output signal be?
Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.
Description : If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?
Last Answer : 800 watts.
Description : One feature of the operational amplifier is that it can have ____________. A. up to ten outputs B. binary coded decimal inputs C. several hundred amps at the output D. inverting and non-inverting inputs
Description : Which transistor configuration provides a phase reversal between the input and output signals?
Last Answer : Common emitter.
Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?
Last Answer : 200 millivolts.
Description : If the input signals are 180 degrees out of phase with each other, what will be the peak-to-peak amplitude of the output signals?
Last Answer : Each output signal will be 100 millivolts.
Description : If the input signals are in phase, what will be the peak-to peak amplitude of the output signals?
Last Answer : 0 volts (the input signals will "cancel out").
Description : 8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv
Last Answer : c) 4, i,ii,iii
Description : State True or False. i) In spooling high speed device like a disk is interposed between running program and low-speed device in Input/output. ii) By using spooling for example instead of writing directly to a printer, ... ii-False B) i-True, ii-True C) i-False, ii-True D) i-False, ii-False
Last Answer : B) i-True, ii-True
Description : List typical inputs and outputs for PLC (four input and any four output).
Last Answer : Typical PLC inputs Push Button Selector Switch Proximity switch FOOT switch, level switch Analog input Typical PLC outputs Contactor Coil, solenoid, relay Indicating Lamp Buzzer Alaram annunciator
Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.
Last Answer : Circuit diagram:- Input / Output waveforms:-
Description : What components form the input-signal-developing impedance for the amplifier?
Last Answer : C2 and the secondary of T1.
Description : If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?
Last Answer : The gain increases.
Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?
Last Answer : 0 volts.
Description : In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?
Last Answer : Idler- or lower-sideband frequency.
Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?
Last Answer : Exactly double the input frequency.
Description : Does an amplifier actually change an input signal? Why or why not?
Last Answer : No, the input signal is unchanged, the output signal is controlled by the input signal but does not effect the actual input signal.
Description : Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?
Last Answer : 35-dB RMS because the highest SNR can always record and reproduce the widest range of input signals.
Description : If C4 were removed from the circuit, what would happen to the output of the amplifier?
Last Answer : The output would decrease. (C4 decouples R2 preventing degenerative feedback from R2.)
Description : If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?
Last Answer : The gain decreases.
Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?
Last Answer : A step-down transformer.
Description : What type coupling is usually used to couple the output from a power amplifier?
Last Answer : Transformer coupling.
Description : An amplifier is said to suffer from distortion when its output is - (1) low (2) different from input (3) noisy (4) larger than its input
Last Answer : (3) noisy Explanation: Amplifier Distortion can take on many forms such as Amplitude, Frequency and Phase Distortion due to Clipping. For a signal amplifier to operate correctly without any distortion to the output signal, it requires some form of DC Bias on its Base or Gate terminal.
Description : An operational amplifier, as used in today's consoles, has a calculated gain of 5. This means that when the input changes _____________. A. 5 volts, the output changes 10 volts B. 10 volts, the output changes 5 volts C. 2 volts, the output changes 10 volts D. 10 volts, the output changes 2 volts
Description : When troubleshooting an amplifier, you measure an output of 30 volts. If the gain of the amplifier is 2, what must the input voltage be for the amplifier to work properly? A. 32 volts B. 30 volts C. 28 volts D. 15 volts
Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Last Answer : Answer: A
Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage
Last Answer : Answer: B
Description : An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts
Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor
Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source
Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals
Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω
Last Answer : B. 2,518 Ω
Description : In inverting amplifier, the phase difference between input and output voltages must be A. 30° B. 45° C. 90° D. 180°
Last Answer : 180°
Description : For non-inverting amplifier the input and output is A. out of phase B. in phase C. have phase difference of 180° D. have phase difference of 90°
Last Answer : in phase
Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal
Last Answer : B) Clipping of output in the positive half of the input signal
Description : The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter
Last Answer : (d) inverter
Description : Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above
Last Answer : (a) Very high input impedance