What component in an amplifier circuit tends to limit the low-frequency response of the amplifier?

What component in an amplifier circuit tends to limit the  low-frequency response of the amplifier?
by

1 Answer

Answer :

The coupling capacitor (C3).
by

Related questions

What are the factors that limit the frequency response of a transistor amplifier?

Description : What are the factors that limit the frequency response of a transistor amplifier?

Last Answer : The capacitance and inductance of the circuit and the interelectrode capacitance of the transistor.

What components can be used to increase the high frequency response of an amplifier?

Description : What compone What components What components can be used to increase the high frequency response of an amplifier?

Last Answer : Peaking coils.

What is the major factor that limits the high-frequency response of an amplifier circuits?

Description : What is the major factor that limits the high-frequency response of an amplifier circuits?

Last Answer : The capacitance of the circuit.

In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes more efficient at lower capacitance. C. the arrangement allows the coupling of the signal while it isolates the biasing of each stage. D. good frequency response.

Description : In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes ... of the signal while it isolates the biasing of each stage. D. good frequency response.

Last Answer : Answer: C

Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?

Description : Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?

Last Answer : Yes.

The main component responsible for the fall of gain of an RC coupled amplifier in low frequency

Description : The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is  (A) The active device itself (tube, or transistor)  (B) stray shunt capacitance Cs  (C) the grid leak resistance Rg  (D) coupling capacitor Cc

Last Answer : The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is coupling capacitor Cc

If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Last Answer : A step-down transformer.

What component is used in a triode amplifier to convert variation in

Description : What component is used in a triode amplifier to convert variation in

Last Answer : A plate load resistor RL

Which digital data encoding method helps overcome a tape recorder’s low-frequency response problems by recording two logic levels for each incoming data bit?

Description : Which digital data encoding method helps overcome a tape recorder’s low-frequency response problems by recording two logic levels for each incoming data bit?

Last Answer : Bi-phase level encoding.

What component(s) is/are used for low-frequency compensation for Q2?

Description : What component(s) is/are used for low-frequency compensation for Q2?

Last Answer : R9 and C5.

Draw the frequency response of DC amplifier. Comment on it.

Description : Draw the frequency response of DC amplifier. Comment on it.

Last Answer : frequency response: Comment : The gain remains constant at its midband value AM down to zero frequency (DC). Directcoupled amplifiers do not suffer gain reduction at low frequencies as compared ... , gain falls off at the high frequency end due to the internal capacitances of the transistor.

State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Description : State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Last Answer : The need of multistage amplifier The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in ... to use a MULTISTAGE AMPLIFIER .  Frequency response of R-C coupled amplifier.

What is the purpose of a frequency-determining network in an rf amplifier?

Description : What is the purpose of a frequency-determining network in an rf amplifier?

Last Answer : To provide maximum impedance at the desired frequency.

What are the upper and lower frequency limits of an amplifier?

Description : What are the upper and lower frequency limits of an amplifier?

Last Answer : The half-power points of a frequency-response curve. The upper and lower limits of the band f frequencies for which the amplifier is most effective.

What is the frequency classification of a magnetic amplifier

Description : What is the frequency classification of a magnetic amplifier

Last Answer : An audio (or low) frequency power amplifier.

In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?

Description : In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?

Last Answer : Idler- or lower-sideband frequency.

The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Last Answer : Exactly double the input frequency.

If C4 were removed from the circuit, what would happen to the output of the amplifier?

Description : If C4 were removed from the circuit, what would happen to the output of the amplifier?

Last Answer : The output would decrease. (C4 decouples R2 preventing degenerative feedback from R2.)

If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Description : If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Last Answer : The gain decreases.

What is the difference between a summing amplifier and an adder circuit?

Description : What is the difference between a summing amplifier and an adder circuit?

Last Answer : The adder simply adds the input signals together while the summing amplifier multiplies the sum of the input signals by the gain of circuit.

If the unity-gain point of the operational amplifier used in question 24 is 500 kilohertz, what is the bandwidth of the circuit?

Description : If the unity-gain point of the operational amplifier used in question 24 is 500 kilohertz, what is the bandwidth of the circuit?

Last Answer : 50 kilohertz (Gain = 10; Gain-Bandwidth Product = 500,000) 500,000(Hz)

For what class of operation is the final rf power amplifier of a plate-modulator circuit biased?

Description : For what class of operation is the final rf power amplifier of a plate-modulator circuit biased?

Last Answer : Class C

If a position servo system tends to oscillate whenever a new position is selected, is the system overdamped or underdamped?

Description : If a position servo system tends to oscillate whenever a new position is selected, is the system overdamped or underdamped?

Last Answer : Underdamped

Which type of optical source tends to operate at higher drive currents to produce light?

Description : Which type of optical source tends to operate at higher drive currents to produce light?

Last Answer : Laser.

Which type of optical fiber (multimode or single mode) tends to have lower loss and produces less signal distortion?

Description : Which type of optical fiber (multimode or single mode) tends to have lower loss and produces less signal distortion?

Last Answer : Single mode fiber.

List four factors that can degrade the frequency response of magnetic tape recorders.

Description : List four factors that can degrade the frequency response of magnetic tape recorders.

Last Answer : a. A too-high or too-low bias signal level setting for the record head. b. An improper reproduce head gap. c. An improper tape transport speed. d. Poor tape-to-head contact.

While measuring frequency response, as the signal generator approaches the lowest and highest frequency the recorder can effectively record, the VTVM reading drops to less than - 3 dB. What does this indicate?

Description : While measuring frequency response, as the signal generator approaches the lowest and highest frequency the recorder can effectively record, the VTVM reading drops to less than - 3 dB. What does this indicate?

Last Answer : The upper and lower limits of the frequency response specification for that tape recorder.

The frequency-response specification of your tape recorder reads within +/ - 3 dB from 150 Hz to 150 kHz at 60 ips. What does this mean?

Description : The frequency-response specification of your tape recorder reads within +/ - 3 dB from 150 Hz to 150 kHz at 60 ips. What does this mean?

Last Answer : The recorder can record all frequencies between 150 Hz and 150 kHz at 60 ips without varying the output amplitude more than 3 dB.

The frequency response of test equipment refers to what aspect of ac voltage measurements?

Description : The frequency response of test equipment refers to what aspect of ac voltage measurements?

Last Answer : the range of frequencies that can accurately be measured.

Name the modulation system in which the frequency alternates between two discrete values in response to the opening and closing of a key?

Description : Name the modulation system in which the frequency alternates between two discrete values in response to the opening and closing of a key?

Last Answer : . Frequency-shift keying.

What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Description : What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Last Answer : . RF transformers are used and the transistor is neutralized.

What compWhat component(s) is/are used for high-frequency compensation for Q1?

Description : What component(s) is/are used for high-frequency compensation for Q1?

Last Answer : L1, L2, and R5.

What device sweeps a band of frequencies to determine frequencies and amplitudes of each frequency component?

Description : What device sweeps a band of frequencies to determine frequencies and amplitudes of each frequency component?

Last Answer : Spectrum analyzer.

The area between base 1 and base 2 in a UJT acts as what type of common circuit component?

Description : The area between base 1 and base 2 in a UJT acts as what type of common circuit component?

Last Answer : Variable resistor.

The head driver circuit in a tape recorder’s direct record electronics component (figure 5-1) performs what function?

Description : The head driver circuit in a tape recorder’s direct record electronics component (figure 5-1) performs what function?

Last Answer : It takes the signal from the summing network, amplifies it, and sends it to the record head for recording.

When you are testing individual components in a circuit, what may cause a defective component to appear good?

Description : When you are testing individual components in a circuit, what may cause a defective component to appear good?

Last Answer : A parallel resistor or diode of similar value.

What component of the D’Arsonval meter movement completes the circuit for current flow to the coil?

Description : What component of the D’Arsonval meter movement completes the circuit for current flow to the coil?

Last Answer : Hairspring.

Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Description : Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Last Answer : A. 1.0025 MHz

Trade-offs between competing effects are necessary for high speed response. Which competing effect (fast transit time, low capacitance, or high quantum efficiency) requires a thin active area?

Description : Trade-offs between competing effects are necessary for high speed response. Which competing effect (fast transit time, low capacitance, or high quantum efficiency) requires a thin active area?

Last Answer : Fast transit time.

The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency end and bypass capacitors at the low frequency end C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and D) shunt capacitors at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

What term is used to describe the frequency at which the filter circuit changes from the point of rejecting the unwanted frequencies to the point of passing the desired frequencies?

Description : What term is used to describe the frequency at which the filter circuit changes from the point of rejecting the unwanted frequencies to the point of passing the desired frequencies?

Last Answer : Frequency cutoff (fco).

What receiver circuit actually produces the IF frequency?

Description : What receiver circuit actually produces the IF frequency?

Last Answer : Mixer.

What equipment uses a calibrated resonant circuit to measure frequency?

Description : What equipment uses a calibrated resonant circuit to measure frequency?

Last Answer : Wavemeter.

How can I reduce the bass response on my car amplifier?

Description : How can I reduce the bass response on my car amplifier?

Last Answer : Try adding a adding a capacitor.

In the illustrated amplifier, the RESET potentiometer A1R2 sets the stability of the control loop by changing the reset time constant. As the potentiometer is turned clockwise _________. EL-0060 A. the gain is increased B. the stability is increased by slowing the response time C. feedback is increased to the summing point at terminal 5 D. response time is increased decreasing stability

Description : In the illustrated amplifier, the RESET potentiometer A1R2 sets the stability of the control loop by changing the reset time constant. As the potentiometer is turned clockwise _________. EL-0060 A. ... is increased to the summing point at terminal 5 D. response time is increased decreasing stability

Last Answer : Answer: B

What components form the input-signal-developing impedance for the amplifier?

Description : What components form the input-signal-developing impedance for the amplifier?

Last Answer : C2 and the secondary of T1.

What problem is caused in an rf amplifier by a loosely coupled transformer?

Description : What problem is caused in an rf amplifier by a loosely coupled transformer?

Last Answer : A too-narrow bandpass.

What is the most common form of coupling for an rf amplifier?

Description : What is the most common form of coupling for an rf amplifier?

Last Answer : Transformer coupling.