Description : What determines the frequency, bandwidth, and power handling capability of a waveguide probe?
Last Answer : Size and shape
Description : What term describes sounds capable of being heard by the human ear?
Last Answer : Sonics.
Description : Which semiconductor sources (LD or LED) emit more focused light and are capable of launching sufficient optical power into both single mode and multimode fibers?
Last Answer : LDs.
Description : In its simplest form, what functions must a radar detector be capable of performing?
Last Answer : Detecting the presence of rf energy.
Description : What are keyboards monitors and printers are they all output devices?
Last Answer : what part of the computer is responsible for executinginstructions to process information
Description : Which printers produce output by mechanical contact between the print head and paper? A. Impact B. Non-impact C. Both (A) and (B) D. None of the Above
Last Answer : A. Impact
Description : What are the prerequisites to assigning Printing Assistant for Landscapes (PAL) printers to a printer group? A. Distribute the printer group to a target system group. B. Check the ... output device using transaction Spool Administration(SPAD) H. Create the output device as a PAL printer
Last Answer : D. Assign the target system to a target system group
Description : Is it possible to install two dual output PCI graphics cards for four total displays?
Last Answer : Yes. If you can find one then you should be able to install a second PCI graphics card to the run the extra monitors.
Description : _________is a copy of Basic Input/Output Operating System (BIOS) routines from Read Only Memory (ROM) into a special area of RAM so that they can be accessed more quickly. A. Dynamic RAM B. Shadow RAM C. Synchronous Graphics RAM D. Video RAM
Last Answer : B. Shadow RAM
Description : Is a Macbook Pro capable of dual-display output?
Last Answer : Yes, you can.
Description : If a voltage (positive or negative) is measured on the "1" output of a flip-flop, what state is it in?
Last Answer : SET state.
Description : In a bistable multivibrator, how many trigger pulses are needed to produce one complete cycle in the output?
Last Answer : Two.
Description : hat establishes the value of the current that flows in the output of figure 4-43?
Last Answer : The frequency of the voltage input.
Description : What is the difference between an RC and an RL differentiator in terms of where the output is developed? is developed?
Last Answer : . In an RC circuit the output is taken across the resistor. In the RL circuit the output is taken across the inductor.
Description : A negative damper with negative bias clamps the most positive extremity of the output wave shape to what polarity (positive or negative)?
Last Answer : Negative potential.
Description : A negative damper damps which extremity of the output waveshape to 0 volts?
Last Answer : Most positive.
Description : What type damper (with bias) clamps the most negative extremity of the output waveform to a negative potential?
Last Answer : Positive clamper with negative bias.
Description : To which polarity does a positive damper with positive bins clamp the most negative extremity of the output waveform (positive or negative)?
Last Answer : Positive potential.
Description : A positive damper clamps which extremity of the output signal to 0 volts?
Last Answer : Most negative.
Description : What is the condition of the diode in a series limiter when an output is developed? In a parallel limiter?
Last Answer : Conducting, cutoff.
Description : What component is in parallel with the output in a parallel limiter?
Last Answer : The diode.
Description : Which portion of a sine-wave input is retained in the output of a series-negative limiter?
Last Answer : Positive.
Description : Which portion of a sine-wave input is retained in the output of a series-positive limiter?
Last Answer : Negative.
Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?
Last Answer : -5 volts.
Description : If C4 were removed from the circuit, what would happen to the output of the amplifier?
Last Answer : The output would decrease. (C4 decouples R2 preventing degenerative feedback from R2.)
Description : If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?
Last Answer : The gain decreases.
Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?
Last Answer : A step-down transformer.
Description : What is the output current in the common-collector circuit?
Last Answer : IE.
Description : In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?
Last Answer : The signals are opposite in polarity or 180 degrees out of phase with each other.
Description : Which transistor configuration provides a phase reversal between the input and output signals?
Last Answer : Common emitter.
Description : What is the output voltage of a CT when it is set on electrical zero?
Last Answer : Zero or minimum voltage.
Description : In a control synchro system, when is the output of the CT reduced to zero?
Last Answer : When the CX and CT rotors are in correspondence.
Description : What is the name given to the electrical output of a CT?
Last Answer : Error signal
Description : Using table 1-1, name two synchros that provide a mechanical output.
Last Answer : The torque receiver (TR) and the torque differential receiver (TDR).
Description : How many clock pulses are required to output a 4-bit number in serial form?
Last Answer : Four.
Description : What will be the output of Q if J is HIGH, PS and CLR are HIGH, and the clock is going negative?
Last Answer : Set, or HIGH (1).
Description : What condition must occur to have a change in the output of a D FF?
Last Answer : A positive-going clock pulse.
Description : For an R-S FF to change output conditions, the inputs must be in what states?
Last Answer : 1 and 0, or opposite states.
Description : In the add mode, what does the output of C2 indicate?
Last Answer : . MSD of the sum.
Description : What is the output of C1?
Last Answer : C1 = 0.
Description : With the inputs shown below, what will be the output of S1, S2, and C2?
Last Answer : MSD of the sum.
Description : . What will be the output of a half adder when both inputs are 1s?
Last Answer : Sum equals 0 with a carry of 1.
Description : . What will be the output of an X-NOR gate when both inputs are LOW?
Last Answer : HIGH.
Description : What type of gate is represented by the output Boolean expression R T Å ?
Last Answer : Exclusive NOR (X-NOR).
Description : A two-input X-OR gate will produce a HIGH output when the inputs are at what logic levels?
Last Answer : . One or the other of the inputs must be HIGH, but not both at the same time.
Description : What will be the output of an X-OR gate when both inputs are HIGH?
Last Answer : Low (0)
Description : The input and output signals of a JFET amplifier have what phase relationship?
Last Answer : They are 180 degrees out of phase.
Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?
Last Answer : 60 millivolts.
Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?
Last Answer : 50 millivolts.
Description : select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).
Last Answer : Both the input signal and the feedback signal.