A negative damper damps which extremity of the output waveshape to 0 volts?

A negative damper damps which extremity of the output  waveshape to 0 volts?
by

1 Answer

Answer :

Most positive.
by

Related questions

What type of bias (positive or negative) is added to a negative damper for the most positive extremity of the wave shape to be clamped above 0 volts?

Description : What type of bias (positive or negative) is added to a negative damper for the most positive extremity of the wave shape to be clamped above 0 volts?

Last Answer : Positive bias.

A positive damper clamps which extremity of the output signal to 0 volts?

Description : A positive damper clamps which extremity of the output signal to 0 volts?

Last Answer : Most negative.

A negative damper with negative bias clamps the most positive extremity of the output wave shape to what polarity (positive or negative)?

Description : A negative damper with negative bias clamps the most positive extremity of the output wave shape to what polarity (positive or negative)?

Last Answer : Negative potential.

What type damper (with bias) clamps the most negative extremity of the output waveform to a negative potential?

Description : What type damper (with bias) clamps the most negative extremity of the output waveform to a negative potential?

Last Answer : Positive clamper with negative bias.

To which polarity does a positive damper with positive bins clamp the most negative extremity of the output waveform (positive or negative)?

Description : To which polarity does a positive damper with positive bins clamp the most negative extremity of the output waveform (positive or negative)?

Last Answer : Positive potential.

What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Last Answer : -5 volts.

The impedance Z offered by transmission line for a travelling wave which damps out the low frequency...

Description : The impedance Z offered by transmission line for a travelling wave which damps out the low frequency oscillation rapidly is also called

Last Answer : The impedance Z offered by transmission line for a travelling wave which damps out the low frequency oscillation rapidly is also called Both surge and natural impedances.

What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Last Answer : 63.7 volts.

If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Last Answer : 15.9 volts.

What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Last Answer : 63.6 volts.

What is the relative length of the discharge time constant with respect to the charge time constant of a damper (long or short)?

Description : What is the relative length of the discharge time constant with respect to the charge time constant of a damper (long or short)?

Last Answer : Long time constant.

What is the relative length of the time constant for the diode capacitor combination in a damper (long or short)?

Description : What is the relative length of the time constant for the diode capacitor combination in a damper (long or short)?

Last Answer : Short time constant.

A flue damper and a vent damper are two examples of _______ a. Combustion air positive shut off devices b. Combustion air negative shut off devices c. Both a. & b. d. None of the above

Description : A flue damper and a vent damper are two examples of _______ a. Combustion air positive shut off devices b. Combustion air negative shut off devices c. Both a. & b. d. None of the above

Last Answer : a. Combustion air positive shut off devices

What is the effect upon an electron that enters the buncher gap when the potential across the grids is at 0 volts?

Description : What is the effect upon an electron that enters the buncher gap when the potential across the grids is at 0 volts?

Last Answer : There is no effect

Express the following in more simple terms. (a) 250,000 volts, (b) 25,000,000 microvolts, (c) 0.001 millivolt.

Description : Express the following in more simple terms. (a) 250,000 volts, (b) 25,000,000 microvolts, (c) 0.001 millivolt.

Last Answer : (a) 250 kV, (b) 25 V, (c) 1µV

If a voltage (positive or negative) is measured on the "1" output of a flip-flop, what state is it in?

Description : If a voltage (positive or negative) is measured on the "1" output of a flip-flop, what state is it in?

Last Answer : SET state.

Which portion of a sine-wave input is retained in the output of a series-negative limiter?

Description : Which portion of a sine-wave input is retained in the output of a series-negative limiter?

Last Answer : Positive.

What will be the output of Q if J is HIGH, PS and CLR are HIGH, and the clock is going negative?

Description : What will be the output of Q if J is HIGH, PS and CLR are HIGH, and the clock is going negative?

Last Answer : Set, or HIGH (1).

A stone weighing 20 N is whirling in a vertical circle at the extremity of a string 100 cm long. The tension in the string will be zero a.at the highest position b.at the lowest position c.at the midway position d.at none of the above e.107 dynes

Description : A stone weighing 20 N is whirling in a vertical circle at the extremity of a string 100 cm long. The tension in the string will be zero a.at the highest position b.at the lowest position c.at the midway position d.at none of the above e.107 dynes

Last Answer : a. at the highest position

Extremity arteriography?

Description : Extremity arteriography?

Last Answer : DefinitionExtremity arteriography is a test that uses x-rays and a special dye (contrast material) to see the arteries in the hands, arms, feet, or legs.Alternative NamesAngiography/arteriography of the extremityHow the ... the area on a TV-like monitor, and uses them as a guide.The dye flows thro

A 17-year-old patient involved in an automobile accident is paralyzed with multiple peripheral extremity injuries. Nutritional support is instituted with a transnasal feeding catheter. Which of the following statement(s) is/are true concerning the patient’s management? a. Feeding into the stomach results in stimulation of the biliary/pancreatic axis which is probably trophic for small bowel b. Gastric secretions will dilute the feedings increasing the risk of diarrhea c. The major risk in this patient is tracheobronchial aspiration d. Placement of the feeding catheter through the pylorus into the first portion of the duodenum reduces the risk of regurgitation and aspiration

Description : A 17-year-old patient involved in an automobile accident is paralyzed with multiple peripheral extremity injuries. Nutritional support is instituted with a transnasal feeding catheter. Which of the ... pylorus into the first portion of the duodenum reduces the risk of regurgitation and aspiration

Last Answer : Answer: a, c, d The use of transnasal feeding catheters for intragastric feeding or for duodenal intubation are popular adjuncts for providing nutritional support by the enteral route. The ... the fourth portion of the duodenum reduces the risk of regurgitation and aspiration of feeding formulas

When the patient who has experienced trauma to an extremity complains of severe burning pain, vasomotor changes, and muscles spasms in the injured extremity, the nurse recognizes that the patient is likely demonstrating signs of a) reflex sympathetic dystrophy syndrome. RSD is frequently chronic and occurs most often in women.

Description : When the patient who has experienced trauma to an extremity complains of severe burning pain, vasomotor changes, and muscles spasms in the injured extremity, the nurse ... heterotrophic ossification. Heterotrophic ossification causes muscular pain and limited muscular contraction and movement.

Last Answer : a) reflex sympathetic dystrophy syndrome. RSD is frequently chronic and occurs most often in women.

Which of the following devices is designed specifically to support and immobilize a body part in a desired position? a) Splint A splint may be applied to a fractured extremity initially until swelling subsides.

Description : Which of the following devices is designed specifically to support and immobilize a body part in a desired position? a) Splint A splint may be applied to a fractured extremity initially until swelling ... d) Trapeze A trapeze is an overhead patient-helping device to promote patient mobility in bed.

Last Answer : a) Splint A splint may be applied to a fractured extremity initially until swelling subsides.

Which of the following terms refers to enlarged, red, and tender lymph nodes? a) Lymphadenitis Acute lymphadenitis is demonstrated by enlarged, red and tender lymph nodes. b) Lymphangitis Lymphangitis is an acute inflammation of the lymphatic channels. c) Lymphedema Lymphedema is demonstrated by swelling of tissues in the extremities because of an increased quantity of lymph that results from an obstruction of lymphatic vessels. d) Elephantiasis Elephantiasis refers to a condition in which chronic swelling of the extremity recedes only slightly with elevation.

Description : Which of the following terms refers to enlarged, red, and tender lymph nodes? a) Lymphadenitis Acute lymphadenitis is demonstrated by enlarged, red and tender lymph nodes. b) Lymphangitis ... refers to a condition in which chronic swelling of the extremity recedes only slightly with elevation.

Last Answer : a) Lymphadenitis Acute lymphadenitis is demonstrated by enlarged, red and tender lymph nodes.

Which of the following observations regarding ulcer formation on the patient’s lower extremity indicate to the nurse that the ulcer is a result of venous insufficiency? a) The border of the ulcer is irregular. The border of an ulcer caused by arterial insufficiency is circular. b) The ulcer is very painful to the patient, even though superficial. Superficial venous insufficiency ulcers cause minimal pain. c) The ulcer base is pale to black. The base of a venous insufficiency ulcer shows beefy red to yellow fibrinous color. d) The ulcer is deep, involving the joint space. Venous insufficiency ulcers are usually superficial.

Description : Which of the following observations regarding ulcer formation on the patient's lower extremity indicate to the nurse that the ulcer is a result of venous insufficiency? a) The border of the ... d) The ulcer is deep, involving the joint space. Venous insufficiency ulcers are usually superficial.

Last Answer : a) The border of the ulcer is irregular. The border of an ulcer caused by arterial insufficiency is circular.

What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts

Description : What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts

Last Answer : Answer: A

In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Description : In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Last Answer : Answer: B

What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts

Description : What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts

Last Answer : Answer: B

A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Description : A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Last Answer : Answer: C

One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all inputs and test for a logic '1' at the output C. open all inputs and test for a logic '0' at the output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Description : One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all ... output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Last Answer : Answer: A

A three phase induction motor is drawing 16 Ampere at 440 Volts. If the operating power factor of the motor is 0.90 and the motor efficiency is 92%, then the mechanical shaft power output of the motor is a) 12.04 kW b) 10.09 kW c) 10.97 kW d) None of the above

Description : A three phase induction motor is drawing 16 Ampere at 440 Volts. If the operating power factor of the motor is 0.90 and the motor efficiency is 92%, then the mechanical shaft power output of the motor is a) 12.04 kW b) 10.09 kW c) 10.97 kW d) None of the above

Last Answer : b) 10.09 kW

What precaution should you take when you use 115 volts to zero a differential?

Description : What precaution should you take when you use 115 volts to zero a differential?

Last Answer : Never leave the circuit energized for more than 2 minutes.

Which breakdown theory explains the action that takes place in a heavily doped PN-junction with a reverse bias of less than 5 volts?

Description : Which breakdown theory explains the action that takes place in a heavily doped PN-junction with a reverse bias of less than 5 volts?

Last Answer : Zener effect.

If a power supply produces 20 volts with no load and 15 volts under full load, what is the percent of regulation?

Description : If a power supply produces 20 volts with no load and 15 volts under full load, what is the percent of regulation?

Last Answer : 33.33%

Convert 2.1 kV to volts.

Description : Convert 2.1 kV to volts.

Last Answer : 2100 volts.

A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Last Answer : 240 volts.

If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?

Description : If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?

Last Answer : 340 volts.

The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Last Answer : 42.

If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total current through the voltage divider?

Description : If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total current through the voltage divider?

Last Answer : 495 mA.

A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Last Answer : 50 volts.

Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?

Description : Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?

Last Answer : 1.25 amperes.

If Eeff is 130 volts and Ieff is 3 amperes, what is the total resistance (RT) in the circuit?

Description : If Eeff is 130 volts and Ieff is 3 amperes, what is the total resistance (RT) in the circuit?

Last Answer : 43.3 ohms.

If the alternating source in Q41 is changed to 200 volts peak-to-peak, what is Iavg?

Description : If the alternating source in Q41 is changed to 200 volts peak-to-peak, what is Iavg?

Last Answer : Iavg = 0.636 × Imax = 1.41 amperes.

a. Define the term "working voltage" of a capacitor. b. What should be the working voltage of a capacitor in a circuit that is operating at 600 volts?

Description : a. Define the term "working voltage" of a capacitor. b. What should be the working voltage of a capacitor in a circuit that is operating at 600 volts?

Last Answer : a. It is the maximum voltage the capacitor can work without risk of damage. b. 900 volts.

A vehicle suspension system consists of a spring and a damper. Stiffness of spring is 3.5 KN/m and damping constant of damper is 400Ns/m. If mass is 50 kg, then damping factor is A 0.606 B 0.10 C 0.666 D 0.471

Description : A vehicle suspension system consists of a spring and a damper. Stiffness of spring is 3.5 KN/m and damping constant of damper is 400Ns/m. If mass is 50 kg, then damping factor is A 0.606 B 0.10 C 0.666 D 0.471

Last Answer : D 0.471

Determine the viscous damping coefficient if damper offers resistance 0.05N at constant velocity 0.04m/sec A 0.8N-sec/m B 1.5N-sec/m C 2.5N-sec/m D 1.25N-sec/m

Description : Determine the viscous damping coefficient if damper offers resistance 0.05N at constant velocity 0.04m/sec A 0.8N-sec/m B 1.5N-sec/m C 2.5N-sec/m D 1.25N-sec/m

Last Answer : D 1.25N-sec/m

Calculate damped natural frequency, if a spring mass damper system is subjected to periodic disturbing force of 30 N. Damping coefficient is equal to 0.76 times of critical damping coefficient and undamped natural frequency is 5 rad/sec A. 3.99 rad/sec B. 2.13 rad/sec C. 4.12 rad/sec D. 3.24 rad/sec

Description : Calculate damped natural frequency, if a spring mass damper system is subjected to periodic disturbing force of 30 N. Damping coefficient is equal to 0.76 times of critical damping coefficient and undamped natural frequency is 5 rad/sec A. 3.99 rad/sec B. 2.13 rad/sec C. 4.12 rad/sec D. 3.24 rad/sec

Last Answer : D. 3.24 rad/sec

If the damper is not provided and the system is in resonance, which of the following is the correct isolation factor? A. 0 B. 0.5 C. 0.25 D. Infinite

Description : If the damper is not provided and the system is in resonance, which of the following is the correct isolation factor? A. 0 B. 0.5 C. 0.25 D. Infinite

Last Answer : D. Infinite

A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural frequency (f n ), respectively, are a) 0.471 and 1.19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz

Description : A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural ... , are a) 0.471 and 1.19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz

Last Answer : a) 0.471 and 1.19 Hz

If the damper is not provided and the system is in resonance, which of the following is the correct isolation factor?(A) 0 (B) 0.5 (C) 0.25 (D) Infinite

Description : If the damper is not provided and the system is in resonance, which of the following is the correct isolation factor?(A) 0 (B) 0.5 (C) 0.25 (D) Infinite

Last Answer : (D) Infinite