Description : In a dual-speed synchro system what determines the two specific speeds at which the data will be transmitted?
Last Answer : The gear ratio between the two transmitters.
Description : Figure 'A' of the diagram shown in the illustration represents a ______________. EL-0092 A. differential transformer B. saturable reactor C. synchro system D. magnetic amplifier
Last Answer : Answer: C
Description : What determines whether these components are considered series or shunt?
Last Answer : . The relationship of the components to the output-signal path.
Description : What factor determines whether a radio wave is reflected or refracted by the ionosphere?
Last Answer : Thickness of ionized layer.
Description : What determines whether a substance is a conductor or an insulator?
Last Answer : The number of valence electrons.
Description : What is the reference point for alignment of all synchro units?
Last Answer : The voltmeter method.
Description : . What type of synchro system is used to transmit very large quantities?
Last Answer : A tri-speed synchro system.
Description : What precaution should you take when substituting a synchro tester in a circuit for a transmitter?
Last Answer : Use only one receiver so as not to overload the tester.
Description : What is the most probable cause of trouble in a synchro system that has all of its receivers reading incorrectly?
Last Answer : The transmitter or main bus.
Description : What type of indicator is usually placed in the stator circuit of a torque synchro system?
Last Answer : An overload indicator.
Description : Name two types of trouble you would expect to find in a newly installed synchro system.
Last Answer : Improper wiring and misalignment.
Description : What should you do with a synchro that has a bad set of bearings?
Last Answer : Replace it.
Description : When you zero a synchro with a synchro tester, what is indicated by a jump in the synchro tester's dial when the S1 and S3 leads are momentarily shorted?
Last Answer : The synchro under test is not on electrical zero.
Description : What method of zeroing a synchro is perhaps the fastest but NOT necessarily the most accurate?
Last Answer : . The electrical lock method.
Description : When you zero a multispeed synchro system which synchro should you zero first?
Last Answer : The coarse synchro.
Description : Why should a synchro be rechecked for zero after it is clamped down?
Last Answer : To ensure that it did not move off zero while it was being clamped.
Description : When is a synchro receiver (TR) properly zeroed?
Last Answer : A TR is zeroed when electrical zero voltages exist across its stator windings at the same time its rotor is on zero or on its mechanical reference position.
Description : What is the purpose of the coarse setting of a synchro?
Last Answer : .It ensures the synchro is on 0º, not 180º.
Description : What is the main reason for using a multispeed synchro system instead of a single-speed synchro system?
Last Answer : Greater accuracy without the loss of self-synchronous operation.
Description : What is the name given to the synchro system that transmits data at two different speeds?
Last Answer : . A dual or double-speed synchro system.
Description : Why are synchro capacitors placed physically close to differentials transmitters and CTs?
Last Answer : To keep the connections as short as possible in order to maintain system.
Description : How are synchro capacitors connected in a circuit?
Last Answer : They are delta-connected across the stator windings.
Description : What type of current is eliminated by synchro capacitors?
Last Answer : Magnetizing current.
Description : What type of synchros usually require the use of synchro capacitors?
Last Answer : TDXs, CDXs, and Cts.
Description : What is the purpose of the synchro capacitor?
Last Answer : To improve overall synchro system accuracy by reducing stator currents.
Description : In a control synchro system, when is the output of the CT reduced to zero?
Last Answer : When the CX and CT rotors are in correspondence.
Description : What type of synchro is used in systems requiring large amounts of power and a high degree of accuracy?
Last Answer : A control synchro.
Description : What leads in a simple synchro system are connected to the ac power line?
Last Answer : The rotor leads.
Description : What two components make up a simple synchro transmission system?
Last Answer : A synchro transmitter and a synchro receiver.
Description : What method is used to prevent oscillations in large synchro units?
Last Answer : Mechanical damping.
Description : What is the physical difference between a synchro transmitter and a synchro receiver?
Last Answer : A synchro receiver uses some form of damping to retard excessive oscillations or spinning.
Description : Describe the zero-position of a synchro transmitter.
Last Answer : The transmitter is in its zero-position when the rotor is aligned with the S2 stator winding.
Description : When will a synchro generate more heat than it is designed to handle?
Last Answer : Synchros have one primary winding that can be turned through 360º and three secondary windings spaced 120º apart.
Description : What unit of measurement refers to the torque of a synchro transmitter
Last Answer : Ounce-inches.
Description : In a TDX system with standard synchro connections, the TX rotor is at 120º and the TDX rotor is at 40º. What position will the TR indicate?
Last Answer : . 80º.
Description : What are the two major components of a synchro?
Last Answer : The rotor and the stator.
Description : On the synchro schematic symbol, what indicates the angular displacement of the rotor?
Last Answer : . The position of the arrow.
Description : Which of the two synchro designation codes is indicated by 5DG on a synchro nameplate?
Last Answer : The Navy prestandard designation code.
Description : What does the code 26V-11TX4D mean on a synchro nameplate?
Last Answer : It is the third modification of a 26-volt 400-hertz (torque) synchro transmitter whose body diameter is between 1.01 and 1.10 inches
Description : What is the difference between a torque synchro and a control synchro?
Last Answer : A torque synchro is used for light loads and a control synchro is used in systems desired to move heavy loads.
Description : Name the two general classifications of synchro systems
Last Answer : Torque and control.
Description : What is the primary purpose of a synchro system?
Last Answer : Precise and rapid transmission of data between equipment and stations.
Description : Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not ... ratio and differential roll speed affect production rate & energy consumed per unit of surface produced
Last Answer : (C) Both the rolls run necessarily at the same speed
Description : What precaution should you take when you use 115 volts to zero a differential?
Last Answer : Never leave the circuit energized for more than 2 minutes.
Description : What are the two types of differential synchros?
Last Answer : The TDX and the TDR.
Description : What is the purpose of using differential synchros instead of regular synchros?
Last Answer : Differential synchros can handle more signals than regular synchros and also perform addition and subtraction functions.
Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?
Last Answer : 200 millivolts. A-18. a. Differential amplifier
Description : If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?
Last Answer : Each output will be a sine wave with a peak-to-peak amplitude of 100 millivolts. The output signals will be 180 degrees out of phase with each other.
Description : How many inputs and outputs are possible with a differential amplifier?
Last Answer : Two inputs, two outputs.
Description : . How do tape transports with differential velocity capstans maintain a constant tape tension in the area around the magnetic heads?
Last Answer : The supply capstan is slightly larger than the take-up capstan. This causes the take-up capstan to pull the tape slightly faster than the supply capstan feeds the tape.