What precaution should you take when you use 115 volts to zero a differential?

What precaution should you take when you use 115 volts  to zero a differential?
by

1 Answer

Answer :

Never leave the circuit energized for more than 2 minutes.
by

Related questions

What precaution should you take when substituting a synchro tester in a circuit for a transmitter?

Description : What precaution should you take when substituting a synchro tester in a circuit for a transmitter?

Last Answer : Use only one receiver so as not to overload the tester.

What safety precaution should you take when working with extruded polytetrafluoroethylene insulated wiring?

Description : What safety precaution should you take when working with extruded polytetrafluoroethylene insulated wiring?

Last Answer : Avoid breathing the vapors when the insulation is heated.

In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Description : In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Last Answer : Answer: B

The power requirements for operating the circuits shown in the illustration are ____________. EL-0099 A. (+) and (-) 50 volts D.C. B. (+) 28 and (+) 50 volts D.C. C. (+) 28 volts D.C. and 115 volts A.C. D. (+) 28 volts and (-) 50 volts D.C.

Description : The power requirements for operating the circuits shown in the illustration are ____________. EL-0099 A. (+) and (-) 50 volts D.C. B. (+) 28 and (+) 50 volts D.C. C. (+) 28 volts D.C. and 115 volts A.C. D. (+) 28 volts and (-) 50 volts D.C.

Last Answer : Answer: A

When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Description : When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Last Answer : Answer: B

Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Description : Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Last Answer : D. 83%

What safety precaution must be taken before replacing a transistor?

Description : What safety precaution must be taken before replacing a transistor?

Last Answer : The power must be removed from the circuit.

What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Description : What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Last Answer : Adequate ventilation.

What determines whether a differential synchro adds or subtracts?

Description : What determines whether a differential synchro adds or subtracts?

Last Answer : The way the differential synchro is connected in a system is the deciding factor on whether the unit adds or subtracts its inputs.

What are the two types of differential synchros?

Description : What are the two types of differential synchros?

Last Answer : The TDX and the TDR.

What is the purpose of using differential synchros instead of regular synchros?

Description : What is the purpose of using differential synchros instead of regular synchros?

Last Answer : Differential synchros can handle more signals than regular synchros and also perform addition and subtraction functions.

If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Last Answer : 200 millivolts. A-18. a. Differential amplifier

If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?

Description : If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?

Last Answer : Each output will be a sine wave with a peak-to-peak amplitude of 100 millivolts. The output signals will be 180 degrees out of phase with each other.

How many inputs and outputs are possible with a differential amplifier?

Description : How many inputs and outputs are possible with a differential amplifier?

Last Answer : Two inputs, two outputs.

. How do tape transports with differential velocity capstans maintain a constant tape tension in the area around the magnetic heads?

Description : . How do tape transports with differential velocity capstans maintain a constant tape tension in the area around the magnetic heads?

Last Answer : The supply capstan is slightly larger than the take-up capstan. This causes the take-up capstan to pull the tape slightly faster than the supply capstan feeds the tape.

What is the general function of the differential voltmeter?

Description : What is the general function of the differential voltmeter?

Last Answer : To compare an unknown voltage with a known reference voltage and indicate the difference in their values.

What are the advantages of using a differential voltmeter?

Description : What are the advantages of using a differential voltmeter?

Last Answer : Accuracy and high input impedance.

My apples having worm in the center how to take precaution of tree?

Description : My apples having worm in the center how to take precaution of tree?

Last Answer : Sun will definitely give you a stronger and better tree, but it sounds like you have been invaded by apple maggot.Territorial seed co. has a sphere in soft form that has a sticky attractant ... will give you a really good security in that it at tracks several critters away from your precious fruit

which of the following is a precaution a worker should take to avoid on-the-job fall hazards? -General Knowledge

Description : which of the following is a precaution a worker should take to avoid on-the-job fall hazards? -General Knowledge

Last Answer : Attend and participate in fall prevention training is a precaution a worker should take to avoid on-the-job fall hazards.

What precaution you should take before copying file from an external storage media? -Technology

Description : What precaution you should take before copying file from an external storage media? -Technology

Last Answer : Precaution should be taken to run an antivirus program before copying any file from floppy disk, USB, DVD etc. Also, we have to run an antivirus program weekly to scan all the drives in the system.

What precaution will should take regarding covid 19?

Description : What precaution will should take regarding covid 19?

Last Answer : Recommended preventive measures include hand washing, covering one's mouth when coughing, maintaining distance from other people, wearing a face mask in public settings, and monitoring and self- ... Many places have also worked to increase testing capacity and trace contacts of infected persons.

Which precaution do people who participate in high-risk behaviors for STIs need to take?

Description : Which precaution do people who participate in high-risk behaviors for STIs need to take?

Last Answer : get a check up every 6 months

What precaution would you take in giving the glucose load?

Description : What precaution would you take in giving the glucose load? 

Last Answer : In order to prevent vomiting, patient is asked to drink it slowly (within about 5 minutes). Flavouring of the solution will also reduce the tendency to vomit.

What type of bias (positive or negative) is added to a negative damper for the most positive extremity of the wave shape to be clamped above 0 volts?

Description : What type of bias (positive or negative) is added to a negative damper for the most positive extremity of the wave shape to be clamped above 0 volts?

Last Answer : Positive bias.

A negative damper damps which extremity of the output waveshape to 0 volts?

Description : A negative damper damps which extremity of the output waveshape to 0 volts?

Last Answer : Most positive.

A positive damper clamps which extremity of the output signal to 0 volts?

Description : A positive damper clamps which extremity of the output signal to 0 volts?

Last Answer : Most negative.

What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Last Answer : -5 volts.

Which breakdown theory explains the action that takes place in a heavily doped PN-junction with a reverse bias of less than 5 volts?

Description : Which breakdown theory explains the action that takes place in a heavily doped PN-junction with a reverse bias of less than 5 volts?

Last Answer : Zener effect.

What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Last Answer : 63.7 volts.

If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Last Answer : 15.9 volts.

If a power supply produces 20 volts with no load and 15 volts under full load, what is the percent of regulation?

Description : If a power supply produces 20 volts with no load and 15 volts under full load, what is the percent of regulation?

Last Answer : 33.33%

What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Last Answer : 63.6 volts.

What is the effect upon an electron that enters the buncher gap when the potential across the grids is at 0 volts?

Description : What is the effect upon an electron that enters the buncher gap when the potential across the grids is at 0 volts?

Last Answer : There is no effect

Express the following in more simple terms. (a) 250,000 volts, (b) 25,000,000 microvolts, (c) 0.001 millivolt.

Description : Express the following in more simple terms. (a) 250,000 volts, (b) 25,000,000 microvolts, (c) 0.001 millivolt.

Last Answer : (a) 250 kV, (b) 25 V, (c) 1µV

Convert 2.1 kV to volts.

Description : Convert 2.1 kV to volts.

Last Answer : 2100 volts.

A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Last Answer : 240 volts.

If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?

Description : If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?

Last Answer : 340 volts.

The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Last Answer : 42.

If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total current through the voltage divider?

Description : If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total current through the voltage divider?

Last Answer : 495 mA.

A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Last Answer : 50 volts.

Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?

Description : Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?

Last Answer : 1.25 amperes.

If Eeff is 130 volts and Ieff is 3 amperes, what is the total resistance (RT) in the circuit?

Description : If Eeff is 130 volts and Ieff is 3 amperes, what is the total resistance (RT) in the circuit?

Last Answer : 43.3 ohms.

If the alternating source in Q41 is changed to 200 volts peak-to-peak, what is Iavg?

Description : If the alternating source in Q41 is changed to 200 volts peak-to-peak, what is Iavg?

Last Answer : Iavg = 0.636 × Imax = 1.41 amperes.

a. Define the term "working voltage" of a capacitor. b. What should be the working voltage of a capacitor in a circuit that is operating at 600 volts?

Description : a. Define the term "working voltage" of a capacitor. b. What should be the working voltage of a capacitor in a circuit that is operating at 600 volts?

Last Answer : a. It is the maximum voltage the capacitor can work without risk of damage. b. 900 volts.

As complete saturation of an adsorbent is approached, the differential heat of adsrop-tion approaches (A) That of normal condensation (B) Integral heat of adsorption (C) Zero (D) None of these

Description : As complete saturation of an adsorbent is approached, the differential heat of adsrop-tion approaches (A) That of normal condensation (B) Integral heat of adsorption (C) Zero (D) None of these

Last Answer : (A) That of normal condensation

Pick out the wrong statement. (A) The integral method of analysing kinetic data is used when the data is scattered (B) The differential method of analysing kinetic data requires more accurate or larger amounts of data (C) When the reaction rate is independent of temperature, the reaction is said to be of zero order (D) The ratio of volumes of plug flow reactor to that of mixed reactor is always less than one for identical feed composition, flow rate, conversion and for all positive reaction orders

Description : Pick out the wrong statement. (A) The integral method of analysing kinetic data is used when the data is scattered (B) The differential method of analysing kinetic data requires more accurate ... less than one for identical feed composition, flow rate, conversion and for all positive reaction orders

Last Answer : (C) When the reaction rate is independent of temperature, the reaction is said to be of zero order

Which of the following statements represents the FIRST precaution to be taken prior to working on any installed electrical component? A. Wear rubber gloves and boots. B. Use only approved nonconducting tools. C. Ground the case of the machine before beginning any repairs. D. Open the supply circuits and tag the switches.

Description : Which of the following statements represents the FIRST precaution to be taken prior to working on any installed electrical component? A. Wear rubber gloves and boots. B. Use only approved nonconducting ... the machine before beginning any repairs. D. Open the supply circuits and tag the switches.

Last Answer : Answer: D

If reading AC current with the illustrated device and unsure of the range as a precaution , the first step should be to _________. EL-0047 A. secure power and test for voltage B. disconnect the lead to be tested and connect the meter in series C. connect the meter to measure resistance and use Ohm's law to calculate current D. unable to safely measure current with the device

Description : If reading AC current with the illustrated device and unsure of the range as a precaution , the first step should be to _________. EL-0047 A. secure power and test for voltage B. disconnect the ... resistance and use Ohm's law to calculate current D. unable to safely measure current with the device

Last Answer : Answer: A

Idea discussion - How useful are super freezers as an additional powerless safety precaution?

Description : Idea discussion - How useful are super freezers as an additional powerless safety precaution?

Last Answer : I think it’a a great idea @mattbrowne! It would be costly, but doable in terms of the cost of reactors now.

What precaution do I need to know when changing an IMAP account to POP3 in Outlook 2007?

Description : What precaution do I need to know when changing an IMAP account to POP3 in Outlook 2007?

Last Answer : answer:I haven't used POP3 in years now. Why do you want to change? Do you want to remove the messages off the server? I don't think you can change an account from one type to ... . You should probably download the messages into a different set of of folders. That would prevent duplicate messages.