When compared to the JFET, what is the input impedance of the MOSFET?

When compared to the JFET, what is the input impedance  of the MOSFET?
by

1 Answer

Answer :

The MOSFET has a higher input impedance.
by

Related questions

Is the input impedance of MOSFET more than BJT and FET?

Description : Is the input impedance of MOSFET more than BJT and FET?

Last Answer : Yes, the input impedance of MOSFET more than BJT and FET.

The input and output signals of a JFET amplifier have what phase relationship?

Description : The input and output signals of a JFET amplifier have what phase relationship?

Last Answer : They are 180 degrees out of phase.

Which of the following low noise transistors is commonly used at microwave frequencies? A. MOSFET B. GASFET C. MESFET D. JFET

Description : Which of the following low noise transistors is commonly used at microwave frequencies? A. MOSFET B. GASFET C. MESFET D. JFET

Last Answer : C. MESFET

The transistor with the lowest noise figure in the microwave region is a A. MOSFET B. Dual-gate MOSFET C. JFET D. MESFET

Description : The transistor with the lowest noise figure in the microwave region is a A. MOSFET B. Dual-gate MOSFET C. JFET D. MESFET

Last Answer : D. MESFET

State advantages of MOSFET over JFET.

Description : State advantages of MOSFET over JFET.

Last Answer : ➨It can be operated in either enhancement mode or depletion mode. ➨MOSFET have much higher input impedance compare to JFET. ➨They have high drain resistance due to lower resistance of channel. ➨It is easy to manufacture. ➨They support high speed of operation compare to JFETs.

Compare JFET with MOSFET.

Description : Compare JFET with MOSFET.

Last Answer : Particulars JFET MOSFET 1) Type Voltage controlled device Voltage controlled device 2) Mode of operation Operates only in depletion mode Operates in depletion and enhancement ... 6) Gate connection Not isolated from substrate Isolated by SiO2 layer from substrate

A depletion MOSFET differs from a JFET in the sense that it has no

Description : A depletion MOSFET differs from a JFET in the sense that it has no   (A) channel (B) gate (C) P-N junctions (D) substrate

Last Answer : A depletion MOSFET differs from a JFET in the sense that it has no P-N junctions 

What components form the input-signal-developing impedance for the amplifier?

Description : What components form the input-signal-developing impedance for the amplifier?

Last Answer : C2 and the secondary of T1.

If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Description : If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Last Answer : The gain increases.

The input impedance of your test equipment should exceed the impedance of the circuit under test by what ratio?

Description : The input impedance of your test equipment should exceed the impedance of the circuit under test by what ratio?

Last Answer : 10 to 1

What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?

Description : What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?

Last Answer : Equal impedance.

What is the normal current path in an N-channel JFET?

Description : What is the normal current path in an N-channel JFET?

Last Answer : From source to drain.

The source and drain of an N-channel JFET are made of what type of material?

Description : The source and drain of an N-channel JFET are made of what type of material?

Last Answer : N-type material.

What are the two types of JFET?

Description : What are the two types of JFET?

Last Answer : N-channel and P-channel.

With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Description : With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Last Answer : Working of N channel FET: * When a voltage is applied between the drain and source with a DC supply (VDD), the electrons flows from source to drain through narrow channel ... where the channel gets completely blocked and the drain current becomes zero is called pinch- off voltage. 

The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Last Answer : Exactly double the input frequency.

What is the purpose of the spring or wire around the leads of a new MOSFET?

Description : What is the purpose of the spring or wire around the leads of a new MOSFET?

Last Answer : To prevent damage from static electricity.

What type of MOSFET can be independently controlled by two separate signals?

Description : What type of MOSFET can be independently controlled by two separate signals?

Last Answer : The dual-gate MOSFET.

. In a MOSFET, which element is insulated from the channel material?

Description : . In a MOSFET, which element is insulated from the channel material?

Last Answer : The gate terminal.

The substrate of an N-channel MOSFET is made of what material?

Description : The substrate of an N-channel MOSFET is made of what material?

Last Answer : P-type material.

What are the four elements of the MOSFET?

Description : What are the four elements of the MOSFET?

Last Answer : Gate, source, drain, and substrate.

A MOSFET can be damaged by an electrostatic discharge at approximately what minimum potential?

Description : A MOSFET can be damaged by an electrostatic discharge at approximately what minimum potential?

Last Answer : 35 volts.

As compared to power MOSFET, a BJT has

Description : As compared to power MOSFET, a BJT has  (a) Lower switching losses but higher conduction losses (b) Higher switching losses and higher conduction losses (c) Higher switching losses but lower conduction losses (d) Lower switching losses and lower conduction losses. 

Last Answer : As compared to power MOSFET, a BJT has Higher switching losses but lower conduction losses 

parallel operation of mosfet can be done more easily as compared to thyristor. why?

Description : parallel operation of MOSFET can be done more easily as compared to thyristor. why?

Last Answer : Parallel operation of MOSFET can be done more easily as compared to thyristor because the resistance of MOSFET is increases with increase in temperature. MOSFET have the positive temperature coefficient. In ... the parallel operation of MOSFET can be done more easily as compared to the thyristor.

What device is used to produce a gradual change in impedance at the end of a waveguide?

Description : What device is used to produce a gradual change in impedance at the end of a waveguide?

Last Answer : Horn.

What is the result of an impedance mismatch in a waveguide?

Description : What is the result of an impedance mismatch in a waveguide?

Last Answer : Standing waves that cause power losses, a reduction in power handling capability, and an increase in frequency and sensitivity.

If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Description : If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Last Answer : The gain decreases.

In a parallel-resonant circuit, what is the relationship between impedance and current?

Description : In a parallel-resonant circuit, what is the relationship between impedance and current?

Last Answer : Maximum impedance, minimum current.

In a series-RLC circuit, what is the condition of the circuit if there is high impedance, low current, and low reactance voltages

Description : In a series-RLC circuit, what is the condition of the circuit if there is high impedance, low current, and low reactance voltages

Last Answer : Nonresonant (circuit is either above or below resonance)

. In an "ideal" resonant circuit, what is the relationship between impedance and current?

Description : . In an "ideal" resonant circuit, what is the relationship between impedance and current?

Last Answer : Impedance low Current high.

If the impedance of the choke is increased, will the ripple amplitude increase or decrease?

Description : If the impedance of the choke is increased, will the ripple amplitude increase or decrease?

Last Answer : Decrease.

The actions of the tr and atr circuits depend on the impedance characteristics of what length of transmission line?

Description : The actions of the tr and atr circuits depend on the impedance characteristics of what length of transmission line?

Last Answer : Quarter-wavelength section

What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?

Description : What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?

Last Answer : High vswr, which equates to poor reception or a loss of power output.

What do impedance-angle meters and vector bridges have in common?

Description : What do impedance-angle meters and vector bridges have in common?

Last Answer : Both measure phase angle and magnitude in determining impedance.

What is the range of the characteristic impedance of lines used in actual practice?

Description : What is the range of the characteristic impedance of lines used in actual practice?

Last Answer : Between 50 and 600 ohms.

What symbol is used to designate the characteristic impedance of a line, and what two variables does it compare?

Description : What symbol is used to designate the characteristic impedance of a line, and what two variables does it compare?

Last Answer : Z0 and it is the ratio of E to I at every point along the line.

What is the impedance of a crystal at its resonant frequency when it is used in the series mode?

Description : What is the impedance of a crystal at its resonant frequency when it is used in the series mode?

Last Answer : Minimum.

What is the impedance of a crystal at its resonant frequency when it is used in the parallel mode?

Description : What is the impedance of a crystal at its resonant frequency when it is used in the parallel mode?

Last Answer : Maximum

Which preamplifier design (high-impedance or transimpedance) provides improvements in bandwidth and greater dynamic range with some degradation in sensitivity from an increase in noise?

Description : Which preamplifier design (high-impedance or transimpedance) provides improvements in bandwidth and greater dynamic range with some degradation in sensitivity from an increase in noise?

Last Answer : Transimpedance.

What happens to the impedance of interelectrode capacitance as frequency increases?

Description : What happens to the impedance of interelectrode capacitance as frequency increases?

Last Answer : Impedance decreases.

In swept-frequency testing the impedance of a transmission line, what electrical characteristic is actually being measured?

Description : In swept-frequency testing the impedance of a transmission line, what electrical characteristic is actually being measured?

Last Answer : Swr on the transmission line.

What is the difference between calculating impedance in a series ac circuit and in a parallel ac circuit?

Description : What is the difference between calculating impedance in a series ac circuit and in a parallel ac circuit?

Last Answer : In a series circuit impedance is calculated from the values of resistance and reactance. In a parallel circuit, the values of resistive current and reactive current must be used to calculate total impedance.

What type of impedance does the tank circuit have above resonance?

Description : What type of impedance does the tank circuit have above resonance?

Last Answer : Inductive.

A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Description : A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output impedance C. low input impedance, low gain and high output impedance D. low input impedance, high gain and low output impedance

Description : Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output ... gain and high output impedance D. low input impedance, high gain and low output impedance

Last Answer : Answer: A

A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Description : A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage is being measured B. input impedance much less than the impedance across which the voltage is being measured C. sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Last Answer : Answer: A

The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω

Description : The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω

Last Answer : B. 300 Ω

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.