Description : The minimum cube strength of concrete used for a pre-stressed member, is (A) 50 kg/cm2 (B) 150 kg/cm2 (C) 250 kg/cm2 (D) 350 kg/cm
Last Answer : Answer: Option D
Description : For testing compressive strength of cement, the size of cube used is (A) 50 mm (B) 70.6 mm (C) 100 mm (D) 150 mm
Last Answer : B
Description : In favourable circumstances a 15 cm concrete cube after 28 days, attains a maximum crushing strength (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm
Description : The compressive strength of 100 mm cube as compared to 150 mm cube is always (A) Less (B) More (C) Equal (D) None of the above
Last Answer : Answer: Option B
Description : Crushing strength of a good building stone should be more than (A) 50 MPa (B) 100 MPa (C) 150 MPa (D) 200 MPa
Description : In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm
Description : The 28 days cube strength of mass concrete using aggregates of maximum size 5 cm for gravity dams should be (A) Between 150 to 300 kg/cm2 (B) Between 350 to 600 kg/cm2 (C) Between 150 to 500 kg/cm2 (D) Below 200 kg/cm2
Description : Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2
Last Answer : (C) 200 kg/cm2
Last Answer : Answer: Option C
Description : Permissible compressive strength of M 150 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2
Description : The slump recommended for mass concrete is about (A) 25 mm to 50 mm (B) 50 mm to 100 mm (C) 100 mm to 125 mm (D) 125 mm to 150 mm
Last Answer : Answer: Option A
Description : Minimum number of 50 kg cement bags per cubic metre of concrete for a mix corresponding to crushing strength 280 kg/cm2 at 28 days, are (A) 5.0 (B) 6.5 (C) 7.0 (D) 7.5
Description : In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine
Last Answer : (B) Secondary
Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option
Last Answer : (C) 120 N/mm
Description : For reinforced concrete work, aggregates having a nominal size of -------- are generally used [ A ] 20 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm
Last Answer : [ A ] 20 mm
Description : Ordinary concrete is not used for concrete grade (A) M 100 (B) M 150 (C) M 250 (D) M 40
Last Answer : (D) M 400
Description : If the various concrete ingredients i.e. cement, sand and aggregates are in the ratio of 1:3:6, the grade of concrete, is (A) M 100 (B) M 150 (C) M 200 (D) M 250
Description : In a tension test, the yield stress is 300 kg/cm2 , in the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm (D) 250 kg/cm2
Last Answer : (A) 100 kg/cm2
Description : Width of the shoulders of carriage way is generally kept (A) 100 cm (B) 125 cm (C) 150 cm (D) 250 cm
Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm
Last Answer : b. 105.4 mm
Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2
Last Answer : (c) 125/p N/mm2
Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm
Description : The maximum permissible chloride content in treated water of public water supplies should not exceed (A) 50 P.P.M. (B) 100 P.P.M. (C) 150 P.P.M. (D) 250 P.P.M.
Last Answer : (D) 250 P.P.M.
Description : Indian Meteorological department uses the standard gauges whose collectors have apertures of (A) 50 or 100 sq. cm area (B) 100 or 150 sq. cm area (C) 100 or 200 sq. cm area (D) 250 or 500 sq. cm area
Description : Permissible compressive strength of M 300 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 300 kg/cm2
Last Answer : (D) 300 kg/cm2
Description : Vibrating screens have capacity in the range of __________ tons/ft 2 .mm mesh size. (A) 0.2 to 0.8 (B) 5 to 25 (C) 50 to 100 (D) 100 to 250
Last Answer : (A) 0.2 to 0.8
Description : Flat rate parcel rates Flat Rate Parcel Boxes size Dimension of boxes (in mm) Weight (in Kg.) Tariff (in Rs.) Small - S 250*50*300 0 to 1 125 Medium - M 250*100*300 Above 1 to 2.5 200 Large - L 300*250*200 Above 2.5 to 5 400
Last Answer : Large - L 300*250*200 Above 2.5 to 5 400
Description : The static deflection of a spring under gravity, when a mass of 1 kg is suspended from it, is 1 mm. Assume the acceleration due to gravity g = 10 m/s^2. The natural frequency of this spring-mass system (in rad/s) is A 100 B 150 C 200 D 250
Last Answer : A 100
Description : For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above
Description : In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine
Last Answer : (C) Fine
Description : In a size reduction crushing operation, feed size is 300 to 1500 mm while the product size is 100 to 300 mm. This is a case of the __________ crushing. (A) Secondary (B) Fine (C) Primary (D) Ultrafine
Last Answer : (C) Primary
Description : The Young's modulus of elasticity of steel, is (A) 150 KN/mm2 (B) 200 KN/mm2 (C) 250 KN/mm2 (D) 275 KN/mm
Description : Minimum thickness of load bearing RCC wall should be (A) 50 mm (B) 100 mm (C) 150 mm (D) 200 mm
Last Answer : (B) 100 mm
Description : Weight per unit of drawbar power is generally ranges between a)50-120kg/kw b)120-150kg/kw c)150-250kg/kw d)250-300kg/kw
Last Answer : a)50-120kg/kw
Description : To determine the modulus of rupture, the size of test specimen used is (A) 150 × 150 × 500 mm (B) 100 × 100 × 700 mm (C) 150 × 150 × 700 mm (D) 100 × 100 × 500 mm
Description : Cube strength of controlled concrete to be used for pre-tensioned and post-tensioned work respectively should not be less than (A) 35 MPa and 42 MPa (B) 42 MPa and 35 MPa (C) 42 MPa and 53 MPa (D) 53 MPa and 42 MPa
Description : Specified compressive strength of concrete is obtained from cube tests at the end of (A) 3 days (B) 7 days (C) 21 days (D) 28 day
Description : The concrete slump recommended for beams and slabs; is (A) 25 to 50 mm (B) 25 to 75 mm (C) 30 to 125 mm (D) 50 to 100 mm
Description : The concrete slump recommended for columns, is (A) 25 to 50 mm (B) 25 to 75 mm (C) 75 to 125 mm (D) 50 to 100 mm
Description : The concrete slump recommended for foundations, is (A) 25 to 50 mm (B) 30 to 125 mm (C) 50 to 100 mm (D) 75 to 125 mm
Description : If the slump of a concrete mix is 50 to 100 mm, its workability is [ A ] Very low [ B ] Low [ C ] Medium [ D ] High
Last Answer : [ C ] Medium
Description : The minimum strength of the mortar used in load bearing brick masonry, is (A) 50 N/cm2 (B) 100 N/cm2 (C) 150 N/cm2 (D) 200 N/cm2
Last Answer : : Option B
Description : For the construction of cement concrete dams, the maximum permissible size of the aggregates, is (A) 40 mm (B) 50 mm (C) 60 mm (D) 70 mm
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm
Description : While placing of concrete the thickness of each layer for R.C.C. is [ A ] 150 to 300 mm [ B ] 450 mm [ C ] 500 to 750 mm [ D ] 500 mm
Last Answer : [ A ] 150 to 300 mm
Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2
Last Answer : c. 50.57 N/mm2
Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 ... joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm
Last Answer : (D) 400 mm
Description : Potassium content of muscle tissue in mg/100 ml is about (A) 50–100 (B) 100–150 (C) 250–400 (D) 150–200
Last Answer : Answer : C
Description : The total serum testosterone in adult men is (A) 50–100 ng/100 ml (B) 150–250 ng/100 ml (C) 300–1000 ng/100 ml (D) 1000–3000 ng/100 ml
Description : The insulin content of pancreas is about (A) 50–70 units (B) 100–150 units (C) 150–180 units (D) 200–250 units
Last Answer : Answer : D