Description : The minimum strength of the mortar used in load bearing brick masonry, is (A) 50 N/cm2 (B) 100 N/cm2 (C) 150 N/cm2 (D) 200 N/cm2
Last Answer : : Option B
Description : In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm
Last Answer : Answer: Option B
Description : The nominal thickness of one brick wall in mm, is (A) 90 mm (B) 150 mm (C) 190 mm (D) 200 mm
Last Answer : Answer: Option D
Description : For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm
Description : The horizontal deflection of a parabolic curved beam of span 10 m and rise 3 m when loaded with a uniformly distributed load l t per horizontal length is (where Ic is the M.I. at the crown, which varies as the slope ... arch). (A) 50/EIc (B) 100/EIc (C) 150/EIc (D) 200/E
Last Answer : (D) 200/E
Description : .Minimum earth cushion required over RCC Box is a) 300 mm b) 600 mm c) 0* d) 1000 mm
Last Answer : c) 0*
Description : The diameter of a domestic sewer pipe laid at gradient 1 in 100 is recommended (A) 100 mm (B) 150 mm (C) 200 mm (D) 175 mm
Last Answer : (B) 150 mm
Description : Pick out the wrong statement. (A) For a pressure vessel to be classified as 'thin vessel', the ratio of wall thickness to mean radius is less than 0.1 (B) For calculating forces and ... Maximum diameter of the opening provided in a pressure vessel, which does not require any compensation is 200 mm
Last Answer : Option B
Description : A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm
Last Answer : (C) 50 mm
Description : The thickness of bituminous carpet varies from (A) 20 to 25 mm (B) 50 to 75 mm (C) 75 to 100 mm (D) 100 to 120 mm
Last Answer : Answer: Option A
Description : The maximum thickness of expansion joint in rigid pavements is (A) 0 (B) 25 mm (C) 50 mm (D) 100 mm
Description : While placing of concrete the thickness of each layer for R.C.C. is [ A ] 150 to 300 mm [ B ] 450 mm [ C ] 500 to 750 mm [ D ] 500 mm
Last Answer : [ A ] 150 to 300 mm
Description : A journal bearing with hydrodynamic lubrication is running steadily with a certain amount of minimum film thickness. When the load and speed are doubled, how does the minimum film thickness vary? [IES-2008 ... Gets reduced to one-fourth of original value (d) Gets reduced to half of original value
Last Answer : (a) Remains unchanged
Description : The slump recommended for mass concrete is about (A) 25 mm to 50 mm (B) 50 mm to 100 mm (C) 100 mm to 125 mm (D) 125 mm to 150 mm
Description : For testing compressive strength of cement, the size of cube used is (A) 50 mm (B) 70.6 mm (C) 100 mm (D) 150 mm
Last Answer : B
Description : Generally the strength of concrete is represented by the crushing stress of concrete cube of size [ A ] 50 mm [ B ] 100 mm [ C ] 150 mm [ D ] 250 mm
Last Answer : [ C ] 150 mm
Description : If the storey height is equal to length of RCC wall, the percentage increase in strength is (A) 0 (B) 10 (C) 20 (D) 30
Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm
Last Answer : b. 105.4 mm
Description : The prescribed hardness limit of potable water ranges between (A) 50 to 75 P.P.M. (B) 75 to 115 P.P.M. (C) 100 to 150 P.P.M. (D) 150 to 200 P.P.M.
Last Answer : (B) 75 to 115 P.P.M.
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm
Last Answer : Answer: Option C
Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm
Description : Indian Meteorological department uses the standard gauges whose collectors have apertures of (A) 50 or 100 sq. cm area (B) 100 or 150 sq. cm area (C) 100 or 200 sq. cm area (D) 250 or 500 sq. cm area
Description : Crushing strength of a good building stone should be more than (A) 50 MPa (B) 100 MPa (C) 150 MPa (D) 200 MPa
Description : The minimum strain at failure in the tensile reinforcement (Fy = 400 MPa) of RCC beam as per limit state method is (a) 0.0020 (b) 0.0028 (c) 0.0037 (d) 0.0045
Last Answer : (c) 0.0037
Description : The static deflection of a spring under gravity, when a mass of 1 kg is suspended from it, is 1 mm. Assume the acceleration due to gravity g = 10 m/s^2. The natural frequency of this spring-mass system (in rad/s) is A 100 B 150 C 200 D 250
Last Answer : A 100
Description : Dimensions of Postcards is a) Max 100 X 150 mm & min 80 X 140 mm b) Max 105 X 149 mm & min 90 X 140 mm c) Max 150 X 200 mm & min 70X 140 mm d) None of these
Last Answer : b) Max 105 X 149 mm & min 90 X 140 mm
Description : The stretcher bond in brick masonry can be used only when the thickness of wall is (A) 90 mm (B) 180 mm (C) 190 mm (D) 280 mm
Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is: (A) 4.0 mm (B) 4.5 mm (C) 5.0 mm (D) 5.5 mm
Last Answer : (C) 5.0 mm
Description : The Young's modulus of elasticity of steel, is (A) 150 KN/mm2 (B) 200 KN/mm2 (C) 250 KN/mm2 (D) 275 KN/mm
Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the ... , is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Last Answer : (C) 20 mm
Description : The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Description : For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm
Last Answer : (B) 75 mm
Description : For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm
Last Answer : (a) 120 mm
Description : A pile is being driven with a drop hammer weighing 1800 kg and having a free fall of 1.00 m. If the penetration with last blow is 5 mm, the load carrying capacity of the pile, -according to the Engineering News formula, is (A) 100 tonnes (B) 50 tonnes (C) 20 tonnes (D) 10 tonnes
Last Answer : (D) 10 tonnes
Description : A 600 mm square bearing plate settles by 15 mm in plate load test on a cohesion-less soil under an intensity of loading of 0.2 N/ram². The settlement of a prototype shallow footing 1 m square under the same intensity of ... (A) 15 mm (B) Between 15 mm and 25 mm (C) 25 mm (D) Greater than 25 mm
Description : A rectangle-shaped open-to-sky tank of water has a length of 2 m and a width of 1 m. If the atmospheric pressure is assumed to be 100 kPa and thickness of the tank walls is assumed to be negligible, the force exerted by ... of water is A. 20 kN B. 50 kN C. 100 kN D. 200 kN
Last Answer : 200 kN
Description : Permissible creep in track is m. 50 mm n. 100 mm o. 125 mm p. 150 mm.*
Last Answer : p. 150 mm.*
Description : Minimum thickness of wall where single Flemish bond can be used is (A) Half brick thick (B) One brick thick (C) One and a half bricks thick (D) Two bricks thick
Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option
Last Answer : (C) 120 N/mm
Description : The compressive strength of 100 mm cube as compared to 150 mm cube is always (A) Less (B) More (C) Equal (D) None of the above
Description : To determine the modulus of rupture, the size of test specimen used is (A) 150 × 150 × 500 mm (B) 100 × 100 × 700 mm (C) 150 × 150 × 700 mm (D) 100 × 100 × 500 mm
Description : A composite flat wall of a furnace is made of two materials 'A' and 'B'. The thermal conductivity of 'A' is twice of that of material 'B', while the thickness of layer of 'A' is half that of B. If the temperature ... drop (in °K) across the layer of material 'A' is (A) 125 (B) 133 (C) 150 (D) 160
Last Answer : (D) 160
Description : Potassium content of muscle tissue in mg/100 ml is about (A) 50–100 (B) 100–150 (C) 250–400 (D) 150–200
Last Answer : Answer : C
Description : The normal concentration of potassium in whole blood is (A) 50 mg/100 ml (B) 100 mg/100 ml (C) 150 mg/100 ml (D) 200 mg/100 ml
Last Answer : Answer : D
Description : The oxidation of 100 gm of fat yields (A) 50 gm water (B) 107 gm water (C) 150 gm water (D) 200 gm water
Last Answer : Answer : B
Description : The insulin content of pancreas is about (A) 50–70 units (B) 100–150 units (C) 150–180 units (D) 200–250 units
Description : For an adult male daily requirement of iodine is (A) 25–50 µg (B) 50–100 µg (C) 100–150 µg (D) 200–250 µg
Last Answer : Answer : A
Description : The total sulphur content of the body is (A) 25–50 gm (B) 50–75 gm (C) 100–125 gm (D) 150–200 gm
Description : The amount of coproporphyrins excreted per day in feces is about (A) 10–50 µgs (B) 100–150 µgs (C) 200–250 µgs (D) 300–1000 µgs
Description : The State Bank of India has created how much crores fund for investing in IT or Fintech startups? A) 200 B) 50 C) 100 D) 150 E) 300
Last Answer : A) 200 Explanation: India s largest public sector lender State Bank of India has created IT innovations and startup fund and have allotted Rs 200 crore for investment in promising ... for any India registered entity for their business promotion in India using information technology for banking.