Description : In cement pressure grouting holes should be drilled at spacing in both direction at a) 150 – 500 mm b) 450 mm c) 500 – 750 mm* d) 1000 mm
Last Answer : c) 500 – 750 mm*
Description : The size of a plane table is (A) 750 mm × 900 mm (B) 600 mm × 750 mm (C) 450 mm × 600 mm (D) 300 mm × 450 mm
Last Answer : (B) 600 mm × 750 mm
Description : Sum of tread and rise must lie between (A) 300 to 350 mm (B) 400 to 450 mm (C) 500 to 550 mm (D) 600 to 650 mm
Last Answer : Answer: Option B
Description : The maximum spacing of main steel in slabs has been limited to [ A ] 250 mm [ B ] 300 mm [ C ] 450 mm [ D ] 500 mm
Last Answer : [ B ] 300 mm
Description : In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm
Description : Side face reinforcement is provided when the depth of beam exceeds [ A ] 250 mm [ B ] 450 mm [ C ] 550 mm [ D ] 750 mm
Last Answer : [ D ] 750 mm
Description : Maximum root zone depth for Maize (a) 200-300 mm (b) 400-600 mm (c) 500-600 mm (d) 350- 450 mm
Last Answer : (b) 400-600 mm
Description : n Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 12.20 < 30.5 m a) 300 mm b) 600 mm* c) 500 mm d) 450 mm
Last Answer : b) 600 mm*
Description : In Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 6.10 < 12.2 m a) 300 mm b) 600 mm c) 450 mm* d) 500 mm
Last Answer : c) 450 mm*
Description : The 28 days cube strength of mass concrete using aggregates of maximum size 5 cm for gravity dams should be (A) Between 150 to 300 kg/cm2 (B) Between 350 to 600 kg/cm2 (C) Between 150 to 500 kg/cm2 (D) Below 200 kg/cm2
Last Answer : Answer: Option D
Description : To prevent segregation, the maximum height for placing concrete, is (A) 100 cm (B) 125 cm (C) 150 cm (D) 200 cm
Last Answer : Answer: Option A
Description : 23.98 × 62.49 × 12.03 = ? × 29.97 a) 500 b) 600 c) 900 d) 450 e) 750
Last Answer : 24× 62.5× 12 = ? × 30 24× 750 = ? × 30 ? = (24× 750) / 30 = 600 Answer: b)
Description : The compound interest accrued on an amount of Rs. 25,500 at the end of three years is Rs. 8,440.5.What would be the simple interest accrued on the same amount at the same rate in the same period? a) Rs. 5,450/- b) Rs. 8,750/- c) Rs. 4,350/- d) Rs. 3,650/- e) Rs. 7,650/-
Last Answer : A = P + Interest = 25500 + 8440.5 = 33940.5 A = P + 1 + (R/100)^3 33940.5 = 25500 a + R/100)^3 a + R/100)^3 = 33940.5 / 25500 a + R/100)^3 = 1.331 a + R/100)^3 = ... R = 10% Simple Interest = Principle Rate Time / 100 = 25500 10 3/100 = 7650 Answer: e)
Description : In the plate loading test for determining the bearing capacity of soil, the size of square bearing plate should be (A) Less than 300 mm (B) Between 300 mm and 750 mm (C) Between 750 mm and 1 m (D) Greater than 1 m
Last Answer : (B) Between 300 mm and 750 mm
Description : The Maximum spacing of the longitudinal bars measured long the periphery of the column should be [ A ] 250 mm [ B ] 300 mm [ C ] 400 mm [ D ] 450 mm
Description : The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm
Last Answer : [ D ] Smaller of five times the effective depth and 450 mm
Description : According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm
Description : According to IS: 456-2000 spacing of vertical stirrups for shear reinforcement has been limited to [ A ] 0.75 d [ B ] 450 mm [ C ] lesser of 0.75 d or 300 mm [ D ] lesser of 0.75d or 450 mm
Last Answer : [ C ] lesser of 0.75 d or 300 mm
Description : Concrete pavement is provided if daily traffic per lane exceeds (A) 500 tonnes (B) 750 tonnes (C) 1000 tonnes (D) 1250 tonnes
Last Answer : Answer: Option C
Description : The property of the ingredients to separate from each other while placing the concrete is called (A) Segregation (B) Compaction (C) Shrinkage (D) Bulking
Description : The value of 'C' of Indian type W.C. shown in the given figure is: (A) 400 mm (B) 450 mm (C) 500 mm (D) 550 mm
Last Answer : (C) 500 mm
Description : Minimum thickness of load bearing RCC wall should be (A) 50 mm (B) 100 mm (C) 150 mm (D) 200 mm
Last Answer : (B) 100 mm
Description : The nominal thickness of one brick wall in mm, is (A) 90 mm (B) 150 mm (C) 190 mm (D) 200 mm
Description : P and Q undertake to do a piece of job for Rs.1200. P alone can do it in 12 days while Q alone can do it in 16 days. With the help of R , they finish it in 6 days. Find the share of P,Q & R. a) 400,600,200 b) 200,400,600 c) 450,400,250 d) 600,450,150
Last Answer : D R;s 1 day work = 1/6 – (1/12 + 1/16) =1/6 – 1/12 – 1/16 = (8-4-3)/48 = 1/48 P:Q:R = ratio of 1 day work = 1/12:1/16 : 1/48 =4:3:1 P’s share = Rs(1200*4/8) =Rs.600 Q’s share = Rs(1200 * 3/8) =Rs.450 R’s share = Rs(1200 * 1/8) =Rs.150
Description : In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2
Last Answer : b) 450 N/mm2
Description : Which of the listed ranges represents specific gravity corrected for temperature for the electrolyte of a fully charged portable lead-acid battery? A. 1.100 to 1.150 B. 1.180 to 1.200 C. 1.280 to 1.300 D. 1.750 to 2.000
Last Answer : Answer: C
Description : The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)
Last Answer : [ C ] Lesser of (a) and (b)
Description : The average thickness of ozone layer in stratosphere is about __________ dobson unit (DU). (A) 20 (B) 230 (C) 750 (D) 1500
Last Answer : (B) 230
Description : A composite flat wall of a furnace is made of two materials 'A' and 'B'. The thermal conductivity of 'A' is twice of that of material 'B', while the thickness of layer of 'A' is half that of B. If the temperature ... drop (in °K) across the layer of material 'A' is (A) 125 (B) 133 (C) 150 (D) 160
Last Answer : (D) 160
Description : The property of fresh concrete, in which the water in the mix tends to rise to the surface while placing and compacting, is called (A) Segregation (B) Bleeding (C) Bulking (D) Creep
Description : To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the ... the water horse power of the pump is (A) 400 (B) 450 (C) 500 (D) 600
Last Answer : (D) 600
Description : Fusion zone in the electric furnace used for reduction of phosphate rock to elemental phosphorous is maintained at __________ °C. (A) 250-300 (B) 500-750 (C) 950-1050 (D) 1400-1450
Last Answer : (D) 1400-1450
Description : In Dry farming, what is the annual rainfall (in mm) available? a. A Less than 550 mm b. B Less than 500 mm c. C Less than 950 mm d. D Less than 750 mm
Last Answer : d. D Less than 750 mm
Description : If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, ... , the fineness modulus of the aggregate, is (A) 7.30 (B) 7.35 (C) 7.40 (D) 7.45
Description : Match List-I (crops) with List-II (water requirement) and select your answer from the code given below- List-I (a) Jowar (b) Soybean (c) Cotton (d) Groundnut List-II 1. 140 mm - 300 mm 2. 350 mm - 450 mm 3. 200 mm - 300 mm 4. 300 mm - ... (b) (c) (d) (A) 3 1 2 4 (B) 4 2 3 1 (C) 1 4 2 3 (D) 3 1 4 2
Last Answer : (C) 1 4 2 3
Description : Explain the requirements of good formwork with names and materials proposed for beam of size 300 X 450 mm with neat labeled sketch.
Last Answer : Requirements of good formwork:- 1. It should be adequately strong to withstand an extensive variety of dead and live loads. For instance, self-weight, weight of reinforcement, weight of wet concrete, loads of ... of concreting. 8. It should be lightweight. 9. It should be easy to remove.
Description : In slump test, each layer of concrete is compacted by a steel rod 60 cm long and of 16 mm diameter for (A) 20 times (B) 25 times (C) 30 times (D) 50 time
Description : What is the range of tempering temperature (°C) for most of the materials? (A) 75-100 (B) 200-300 (C) 350-450 (D) 500-600
Last Answer : (B) 200-300
Description : Hot extrusion of aluminium is done in the temperature range of __________ °C. (A) 550-600 (B) 450-500 (C) 350-400 (D) 250-300
Last Answer : (C) 350-400
Description : What is the range of the visible light cure beam: A. 100-120 nm B. 200-300 nm C. 400-430 nm D. 470 nm or 450-500 nm
Last Answer : D. 470 nm or 450-500 nm
Description : To determine the modulus of rupture, the size of test specimen used is (A) 150 × 150 × 500 mm (B) 100 × 100 × 700 mm (C) 150 × 150 × 700 mm (D) 100 × 100 × 500 mm
Description : Permissible compressive strength of M 300 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 300 kg/cm2
Last Answer : (D) 300 kg/cm2
Description : What is the clear distance between two consecutive steel channel sleepers on Girder bridges? (a) 450 mm* (b) 510 mm (c) 500 mm (d) 460 mm
Last Answer : (a) 450 mm*
Description : What is the clear distance between two consecutive bridge Timbers or Girder bridge? (a) 450 mm (b) 510 mm* (c) 500 mm (d) 520 mm
Last Answer : (b) 510 mm*
Description : Clear distance between consecutive sleepers not to exceed on bridges in BG is a) 450 mm* b) 600 mm c) 510 mm d) 500 mm
Last Answer : a) 450 mm*
Description : The slump recommended for mass concrete is about (A) 25 mm to 50 mm (B) 50 mm to 100 mm (C) 100 mm to 125 mm (D) 125 mm to 150 mm
Description : Generally the strength of concrete is represented by the crushing stress of concrete cube of size [ A ] 50 mm [ B ] 100 mm [ C ] 150 mm [ D ] 250 mm
Last Answer : [ C ] 150 mm
Description : While designing a stair, the product of rise and going is approximately kept equal to (A) 350 (B) 420 (C) 450 (D) 500
Description : The temperature at which plastic layer formation takes place during carbonisation of coal varies from __________ °C. (A) 100 to 150 (B) 350 to 450 (C) 550 to 650 (D) 700 to 850
Last Answer : (B) 350 to 450
Description : The grade of concrete not recommended by I.S. : 456, is (A) M 100 (B) M 200 (C) M 300 (D) M 500
Last Answer : (D) M 500