Shear strain energy theory for the failure of a material at elastic limit, is due to
(A) Rankine
(B) Guest or Trecas
(C) St. Venant
(D) Von Mises
Description : Maximum principal stress theory for the failure of a material at elastic point, is known (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Von Mises' theory
Last Answer : (C) Rankine's theory
Description : Total strain energy theory for the failure of a material at elastic limit, is known (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory
Last Answer : (D) Haig's theory
Description : Maximum strain theory for the failure of a material at the elastic limit, is known as (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory
Last Answer : (B) St. Venant's theory
Description : Maximum shear stress theory for the failure of a material at the elastic limit, is known (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory
Last Answer : (A) Guest's or Trecas' theory
Description : Shear strain energy theory is also known as (a) Von Mises Theory (b) Coulomb’s theory (c) Rankine theory (d) None
Last Answer : (a) Von Mises Theory
Description : Shear strain energy theory is also known as ( a) Huber theory (b) Rankine theory (c) Mises-Hencky theory (d) None
Last Answer : (c) Mises-Hencky theory
Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum shear stress theory (d) None
Last Answer : (d) None
Description : The design of shafts made of brittle materials is based on (a) Guest’s theory (b) Rankine’s theory (c) St. Venant’s theory (d) Von Mises Theory
Last Answer : (b) Rankine’s theory
Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum Principal stress theory (d) None
Last Answer : (c) Thirdly Maximum Principal stress theory
Description : Which of the following theories of failure is most appropriate for a brittle material? (a) Maximum principal strain theory (b) Maximum principal stress theory (c) Maximum shear stress theory (d) Maximum strain energy theory
Last Answer : (b) Maximum principal stress theory
Description : Maximum total strain energy theory is also known as (a) Huber theory (b) Rankine theory (c) St.Venant’s theory (d) None
Last Answer : (a) Huber theory
Description : Shear strain energy theory is also known as (a) Coulomb’s theory (b) Distortion energy theory (c) Rankine theory (d) None
Last Answer : (b) Distortion energy theory
Description : A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Shear Stress Theory (b) Secondly Maximum Shear Strain Energy Theory (c) Both (a) & (b) (d) None
Last Answer : (c) Both (a) & (b)
Description : A power transmitting ductile material shaft under P, T and M will be designed on the basis of (a) Rankine theory (b) Guest Theory (c) Haigh theory (d) None
Last Answer : (b) Guest Theory
Description : The Muskingum method of flood routing is a (a) Form of hydraulic routing of a flood (b) Form of reservoir routing (c) Complete numerical solution of St. Venant equations (d) Hydrological channel routing method
Last Answer : (d) Hydrological channel routing method
Description : The ratio of shear stress and shear strain of an elastic material, is (A) Modulus of Rigidity (B) Shear Modulus (C) Modulus of Elasticity (D) Both (a) and (b)
Last Answer : (D) Both (a) and (b)
Description : For a homogeneous & isotropic body under hydrostatic pressure, which theory of elastic failure fails (a) Firstly Maximum Principal Theory (b) Secondly Maximum Principal strain Theory (c) Thirdly Maximum Principal Energy Theory (d) None
Last Answer : (c) Thirdly Maximum Principal Energy Theory
Description : For a homogeneous & isotropic body under hydrostatic pressure, which theory of elastic failure does not fail (a) Firstly Maximum Principal Theory (b) Secondly Maximum Shear Stress Theory (c) Thirdly Maximum Principal Energy Theory (d) None
Last Answer : (a) Firstly Maximum Principal Theory
Description : The idea that government's fiscal policy can be used to stabilize the level of output and employment can be attributed to which of the following economists: a) Frederich Hayek b) Ludwig von Mises c) Frederic Bastiat d) John Maynard Keynes
Last Answer : d) John Maynard Keynes John Maynard Keynes's 1936 book, 'The General Theory of Employment, Interest, and Money' laid the foundations for Macroeconomics
Description : Maximum principal theory is also known as (a) Guest Theory (b) Beltrami Theory (c) Rankine Theory (d) None
Last Answer : (c) Rankine Theory
Description : What is the maximum value of deforming force upto which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress
Last Answer : (3) Elastic Limit Explanation: The Maximum Extent to which a solid may be stretched without permanent alteration of size or shape.
Description : What is the maximum value of deforming force up to which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress
Last Answer : (4) Elastic Limit Explanation: The Maximum Extent to which a solid may be stretched without permanent alteration of size or shape.
Description : As the elastic limit reaches, tensile strain (A) Increases more rapidly (B) Decreases more rapidly (C) Increases in proportion to the stress (D) Decreases in proportion to the stress
Last Answer : (A) Increases more rapidly
Description : A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Principal Theory (b) Secondly Maximum Principal Strain Theory (c) Thirdly Maximum principal strain energy theory (d) None
Description : The Mohr's straight theory is based on the following fact: (A) Material fails essentially by shear (B) Ultimate strength of the material is determined by the stress in the plane of slip (C) Failure criterion is independent of the intermediate principal stress (D) All the above
Last Answer : Answer: Option D
Description : Which theory is perfect for design of shaft when it mades from brittle materials........... A. Rankine theory B. Guest's theory C. Vonmises theory D. St. Venant's theory.
Last Answer : A. Rankine theory
Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these
Last Answer : (B) Endurance limit
Description : Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point
Last Answer : (d) below the yield point
Description : Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails (A) Below the yield point (B) Above the yield point (C) Below the elastic limit (D) At the elastic limit
Last Answer : Option A
Description : Maximum shear stress theory is also called as (a) Guest’s theory (b) Haigh theory (c) Rankine theory (d) None
Last Answer : (a) Guest’s theory
Description : The minimum strain at failure in the tensile reinforcement (Fy = 400 MPa) of RCC beam as per limit state method is (a) 0.0020 (b) 0.0028 (c) 0.0037 (d) 0.0045
Last Answer : (c) 0.0037
Description : Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild ... , 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5
Last Answer : (c) 4, 1, 3, 5 and 2
Description : Consider the following statements: 1. Failure occurs beyond elastic limit 2. Rupture takes place immediately after elastic limit 3. Permanent set occurs beyond elastic limit Which of these are considered in the theories of failure? (a) 1, 2 and 3 (b) 1 and 3 only (c) 2 and 3 only d) 1 and 2 only
Last Answer : d) 1 and 2 only
Description : Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco ... (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above
Last Answer : (D) All the above
Description : Maximum total strain energy theory is also known as (a) Guest’s theory (b) Haigh theory (c) St.Venant’s theory (d) None
Last Answer : (b) Haigh theory
Description : All materials obey Hooke's law within elastic limit. When elastic limit is reached, the tensile strain (A) Increases very quickly (B) Decreases very quickly (C) Increases in proportion to stress (D) Decreases in proportion to stress
Last Answer : (A) Increases very quickly
Description : Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C
Description : Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these
Last Answer : (A) Applies to elastic deformation
Description : cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is (A) 0 (B) 0.33 (C) 0.44 (D) 0.25
Last Answer : Option C
Description : The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point
Last Answer : (b) Proportional Limit
Description : Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment
Last Answer : d. Is ability to resist maximum twisting moment
Description : The material in which large deformation is possible before absolute failure by rupture takes place, is known as (a) Ductile (b) Plastic (c) Brittle (d) Elastic
Last Answer : Ductile
Description : Maximum principal strain theory is also called as (a) Guest’s theory (b) Haigh theory (c) St.Venant’s theory (d) None
Last Answer : (c) St.Venant’s theory
Description : Every material obeys the Hooke's law within its (A) Elastic limit (B) Plastic point (C) Limit of proportionality (D) None of these
Last Answer : (C) Limit of proportionality
Description : The area under stress-strain curve represents a.Hardness of material b.Breaking strength of the material c.Energy required to cause failure d.Toughness of material e.Malleabbility of material
Last Answer : c. Energy required to cause failure
Description : Long and short spans of a two way slab are ly and lx and load on the slab acting on strips parallel to lx and ly be wx and wy respectively. According to Rankine Grashoff theory (A) (wx /wy ) = (ly /lx ) (B) (wx/wy) = (ly/lx)² (C) (wx /wy ) = (ly /lx )4 (D) None of these
Last Answer : Answer: Option C
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : Depending upon the properties of a material, the failure envelope may (A) Be either straight or curved (B) Pass through the origin of stress (C) Intersect the shear stress axis (D) All the above
Description : The law which states, "Within elastic limits strain produced is proportional to the stress producing it", is known as (A) Bernoulli's law (B) Stress law (C) Hooke's law (D) Poisson's law
Last Answer : (C) Hooke's law
Description : Creep coefficient is the ratio of [ A ] Ultimate Creep strain to elastic strain [ B ] Elastic strain to ultimate Creep strain [ C ] Elastic strain to plastic strain [ D ] Plastic strain to elastic strain
Last Answer : [ A ] Ultimate Creep strain to elastic strain