Description : The Maximum shear stress in Slabs should not exceed -------- the maximum values allowed for beams. [ A ] Half Of [ B ] One-Fourth Of [ C ] Twice [ D ] Those Given In
Last Answer : [ A ] Half Of
Description : The diameter of the Links in column should be at least……….of the largest diameter of the longitudinal steel [ A ] One-half [ B ] Three-fourth [ C ] One eighth [ D ] One – fourth
Last Answer : [ D ] One – fourth
Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab
Last Answer : Answer: Option C
Description : The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom
Last Answer : Answer: Option D
Description : Center of gravity of a solid cone lies on the axis at the height (A) One-fourth of the total height above base (B) One-third of the total height above base (C) One-half of the total height above base (D) Three-eighth of the total height above the base
Last Answer : (A) One-fourth of the total height above base
Description : Center of gravity of a thin hollow cone lies on the axis at a height of (A) One-fourth of the total height above base (B) One-third of the total height above base (C) One-half of the total height above base (D) Three-eighth of the total height above the base
Last Answer : (B) One-third of the total height above base
Description : The effective width of a column strip of a flat slab, is (A) One-fourth the width of the panel (B) Half the width of the panel (C) Radius of the column (D) Diameter of the column
Last Answer : Answer: Option B
Description : In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv
Last Answer : [ A ] i and iii
Description : The ratio of the diameter of reinforcing bars and the slab thickness is (A) 1/4 (B) 1/5 (C) 1/6 (D) 1/8
Last Answer : (D) 1/8
Description : According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel
Last Answer : [ C ] One-fourth the diameter of longitudinal steel
Description : The width of the flange of a L-beam, should be less than (A) One-sixth of the effective span (B) Breadth of the rib + four times thickness of the slab (C) Breadth of the rib + half clear distance between ribs (D) Least of the above
Description : The toe projection of foundation slabs is taken (A) As one third of the base (B) As one sixth of overall height of the wall (C) Equal to heel slab (D) Below ground surface
Last Answer : Answer: Option A
Description : Consider the following activities in a building construction: 1. Concreting of roof slabs 2. Brick-jelly lime concrete terracing 3. Erection of form work for slab 4. Construction of parapet wall in terrace The correct sequence of these ... (B) 3, 1, 4, 2 (C) 3, 1, 2, 4 (D) 1, 3, 4, 2
Last Answer : (C) 3, 1, 2, 4
Description : Critical section for shear in case of flat slabs is at a distance of (A) Effective depth of slab from periphery of column/drop panel (B) d/2 from periphery of column/capital/ drop panel (C) At the drop panel of slab (D) At the periphery of column
Description : Pick up the correct statement from the following: (A) The roof slabs of multi-storeyed buildings are constructed monolithically to carry the various floor loads (B) The beams of multi-storeyed ... slab is spanned across the secondary beams provided between the main beams (D) All of these
Description : Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii
Last Answer : [ A ] i
Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²
Description : Liquefied Petroleum Gas (LPG) in domestic use cylinders is in the liquid form. The density of LPG in liquid form is about __________ of that of water (i.e. 1 gm/c.c). (A) One fourth (B) One third (C) Half (D) One eighth
Last Answer : (C) Half
Description : In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above
Description : The thickness of flange in a T-beam is taken equal to the total thickness of the slab, including cover. (a) True (b) False (c) Not known (d) None of these
Last Answer : (a) True
Description : In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.
Last Answer : (c) Width of the portion of the beam in the compression zone
Description : The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)
Last Answer : [ C ] Lesser of (a) and (b)
Description : The concrete work for the following part of the building of specified thickness is measured in square metres (A) Root slabs (B) Floors (C) Wall panels (D) All the above
Last Answer : (D) All the above
Description : In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net ... load should not exceed (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Description : The maximum spacing of main steel in slabs has been limited to [ A ] 250 mm [ B ] 300 mm [ C ] 450 mm [ D ] 500 mm
Last Answer : [ B ] 300 mm
Description : Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse ... aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above
Last Answer : (d) All the above
Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is: (A) 4.0 mm (B) 4.5 mm (C) 5.0 mm (D) 5.5 mm
Last Answer : (C) 5.0 mm
Description : Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not ... The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above
Last Answer : [ B ] The number of longitudinal bars in a circular column should not exceed four
Description : In a slab, the pitch of the main reinforcement should not exceed its effective depth (A) Three times (B) Four times (C) Five times (D) Two times
Description : The pitch of the main bars in a simply supported slab, should not exceed its effective depth by (A) Three times (B) Four times (C) Five times (D) Six times
Description : For a ribbed slab (A) Clear spacing between ribs shall not be greater than 4.5 cm (B) Width of the rib shall not be less than 7.5 cm (C) Overall depth of the slab shall not exceed four times the breadth of the rib (D) All the above
Description : The pitch of bars of main reinforcement in slab should not exceed ________the effective depth of slab. (a) Double (b) Three times (c) Five times (d) Six times
Last Answer : (b) Three times
Description : In a limit state method of design, when shear reinforcement is not provided, the calculated shear stress at the critical section of a slab shall not exceed; [ A ] Ks 0.25 v fck [ B ] ks 0.20 v fck [ C ] ks 0.16 v fck [ D ] ks 0.10 v fck
Last Answer : [ A ] Ks 0.25 v fck
Description : n Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 12.20 < 30.5 m a) 300 mm b) 600 mm* c) 500 mm d) 450 mm
Last Answer : b) 600 mm*
Description : In Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 6.10 < 12.2 m a) 300 mm b) 600 mm c) 450 mm* d) 500 mm
Last Answer : c) 450 mm*
Description : Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30
Last Answer : (B) 25
Description : The power transmitted through the pipe is maximum when the head lost due to friction is equal to (A) One-fourth of the total supply head (B) One-third of the total supply head (C) One-half of the total supply head (D) Two-third of the total supply head
Description : The maximum diameter of a bar used in a ribbed slab, is (A) 12 mm (B) 6 mm (C) 20 mm (D) 22 mm
Description : A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter
Last Answer : (b) 8 mm diameter
Description : The diameter of bars used for distribution reinforcement in slabs, may vary from (a) 2 to 4mm (b) 4 to 6mm (c) 6mm to 8mm (d) 8 to 12mm
Last Answer : (c) 6mm to 8mm
Description : The diameter of bars for main reinforcement in slabs, may be (a) 2 to 4mm (b) 4 to 8mm (c) 8 to 14mm (d) 14 to 18mm
Last Answer : (c) 8 to 14mm
Description : The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 7 mm
Description : In a short cylindrical external mouthpiece, the vena contracta occurs at a distance __________ the diameter of the orifice from the outlet of orifice. (A) Equal to (B) One-fourth (C) One-third (D) One-half
Description : The discharge through a convergent mouthpiece is __________ the discharge through an internal mouthpiece of the same diameter and head of water. (A) Equal to (B) One-half (C) Three fourth (D) Double
Description : The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above
Description : The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these
Description : The thickness of the topping of a ribbed slab, varies between (A) 3 cm to 5 cm (B) 5 cm to 8 cm (C) 8 cm to 10 cm (D) 12 cm to 15 cm
Description : The minimum thickness of a flat slab is taken (A) L/32 for end panels without drops (B) L/36 for end panels without drops (C) L/36 for interior panels without drop (D) All the above
Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm
Description : Interior thickness of concrete road slab for design wheel load 6300 kg and permissible flexural stress 21 kg/cm2 , is (A) 17.0 cm (B) 25.5 cm (C) 34.0 cm (D) 42.5 cm