The minimum thickness of a flat slab is taken (A) L/32 for end panels without drops (B) L/36 for end panels without drops (C) L/36 for interior panels without drop (D) All the above

The minimum thickness of a flat slab is taken
(A) L/32 for end panels without drops
(B) L/36 for end panels without drops
(C) L/36 for interior panels without drop
(D) All the above
by

1 Answer

Answer :

Answer: Option D
by

Related questions

Enlarged head of a supporting column of a flat slab is technically known as (A) Supporting end of the column (B) Top of the column (C) Capital (D) Drop panel

Description : Enlarged head of a supporting column of a flat slab is technically known as (A) Supporting end of the column (B) Top of the column (C) Capital (D) Drop panel

Last Answer : Answer: Option C

Interior thickness of concrete road slab for design wheel load 6300 kg and permissible flexural stress 21 kg/cm2 , is (A) 17.0 cm (B) 25.5 cm (C) 34.0 cm (D) 42.5 cm

Description : Interior thickness of concrete road slab for design wheel load 6300 kg and permissible flexural stress 21 kg/cm2 , is (A) 17.0 cm (B) 25.5 cm (C) 34.0 cm (D) 42.5 cm

Last Answer : Answer: Option B

If d is the economic designed depth of a slab, the thickness of the cement concrete pavement slab at interior, is kept (A) 1.275 d (B) 1.125 d (C) 0.85 d (D) 0.75 d

Description : If d is the economic designed depth of a slab, the thickness of the cement concrete pavement slab at interior, is kept (A) 1.275 d (B) 1.125 d (C) 0.85 d (D) 0.75 d

Last Answer : Answer: Option C

Thickened part of a flat slab over its supporting column, is technically known as (A) Drop panel (B) Capital (C) Column head (D) None of these

Description : Thickened part of a flat slab over its supporting column, is technically known as (A) Drop panel (B) Capital (C) Column head (D) None of these

Last Answer : Answer: Option A

Critical section for shear in case of flat slabs is at a distance of (A) Effective depth of slab from periphery of column/drop panel (B) d/2 from periphery of column/capital/ drop panel (C) At the drop panel of slab (D) At the periphery of column

Description : Critical section for shear in case of flat slabs is at a distance of (A) Effective depth of slab from periphery of column/drop panel (B) d/2 from periphery of column/capital/ drop panel (C) At the drop panel of slab (D) At the periphery of column

Last Answer : Answer: Option B

The width of the flange of a L-beam, should be less than (A) One-sixth of the effective span (B) Breadth of the rib + four times thickness of the slab (C) Breadth of the rib + half clear distance between ribs (D) Least of the above

Description : The width of the flange of a L-beam, should be less than (A) One-sixth of the effective span (B) Breadth of the rib + four times thickness of the slab (C) Breadth of the rib + half clear distance between ribs (D) Least of the above

Last Answer : Answer: Option D

The thickness of flange in a T-beam is taken equal to the total thickness of the slab, including cover. (a) True (b) False (c) Not known (d) None of these

Description : The thickness of flange in a T-beam is taken equal to the total thickness of the slab, including cover. (a) True (b) False (c) Not known (d) None of these

Last Answer : (a) True

If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than (A) WL/12 (L - 2D/3)² (B) WL/10 (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Last Answer : Answer: Option C

The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Description : The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Last Answer : Ans: (c) Correct Answer is: 0.45 m

In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Description : In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Last Answer : Answer: Option D

The concrete work for the following part of the building of specified thickness is measured in square metres (A) Root slabs (B) Floors (C) Wall panels (D) All the above

Description : The concrete work for the following part of the building of specified thickness is measured in square metres (A) Root slabs (B) Floors (C) Wall panels (D) All the above

Last Answer : (D) All the above

Herringbone bond is used for (A) Walls having thickness more than 4 bricks (B) Architectural finish to the face work (C) Ornamental panels in brick flooring (D) All the above

Description : Herringbone bond is used for (A) Walls having thickness more than 4 bricks (B) Architectural finish to the face work (C) Ornamental panels in brick flooring (D) All the above

Last Answer : Answer: Option D

A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion

Description : A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion

Last Answer : (b) Flat slab

A composite flat wall of a furnace is made of two materials 'A' and 'B'. The thermal conductivity of 'A' is twice of that of material 'B', while the thickness of layer of 'A' is half that of B. If the temperature at the two sides of the wall are 400 and 1200°K, then the temperature drop (in °K) across the layer of material 'A' is (A) 125 (B) 133 (C) 150 (D) 160

Description : A composite flat wall of a furnace is made of two materials 'A' and 'B'. The thermal conductivity of 'A' is twice of that of material 'B', while the thickness of layer of 'A' is half that of B. If the temperature ... drop (in °K) across the layer of material 'A' is (A) 125 (B) 133 (C) 150 (D) 160

Last Answer : (D) 160

Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of the column (C) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Description : Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of ... ) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Last Answer : Answer: Option C

In a concrete pavement, during summer, at and soon after mid-day, the combined stress at the interior of the slab is equal to : (a) Wheel load stress + Temperature warping stress + Sub grade resistance stress (b) Wheel load stress + Temperature warping stress – Sub grade resistant stress (c) Wheel load stress – Temperature warping stress + Sub grade resistant stress (d) Wheel load stress – Temperature warping stress − Sub grade resistant stress

Description : In a concrete pavement, during summer, at and soon after mid-day, the combined stress at the interior of the slab is equal to : (a) Wheel load stress + Temperature warping stress + Sub ... + Sub grade resistant stress (d) Wheel load stress - Temperature warping stress − Sub grade resistant stress

Last Answer : (b) Wheel load stress + Temperature warping stress – Sub grade resistant stress

The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom

Description : The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom

Last Answer : Answer: Option D

The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above

Description : The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above

Last Answer : Answer: Option D

The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Description : The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Last Answer : Answer: Option B

The thickness of the topping of a ribbed slab, varies between (A) 3 cm to 5 cm (B) 5 cm to 8 cm (C) 8 cm to 10 cm (D) 12 cm to 15 cm

Description : The thickness of the topping of a ribbed slab, varies between (A) 3 cm to 5 cm (B) 5 cm to 8 cm (C) 8 cm to 10 cm (D) 12 cm to 15 cm

Last Answer : Answer: Option B

If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Last Answer : Answer: Option C

The ratio of the diameter of reinforcing bars and the slab thickness is (A) 1/4 (B) 1/5 (C) 1/6 (D) 1/8

Description : The ratio of the diameter of reinforcing bars and the slab thickness is (A) 1/4 (B) 1/5 (C) 1/6 (D) 1/8

Last Answer : (D) 1/8

The effective span of a simply supported slab is (a) Distance between the centers of the bearings (b) Clear distance between the inner faces of the walls plus twice he thickness of the slab. (c) Cleat spa plus effective depth of the slab. (d) All the above

Description : The effective span of a simply supported slab is (a) Distance between the centers of the bearings (b) Clear distance between the inner faces of the walls plus twice he thickness of the slab. (c) Cleat spa plus effective depth of the slab. (d) All the above

Last Answer : (c) Cleat spa plus effective depth of the slab.

In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Description : In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Last Answer : (d) Depth of rib

In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.

Description : In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.

Last Answer : (c) Width of the portion of the beam in the compression zone

The portion of the slab which acts monolithically with the beam and which resists the compressive stresses, is called _________of flange of the T-beam (a) Length (b) Breadth (c) Thickness (d) Depth

Description : The portion of the slab which acts monolithically with the beam and which resists the compressive stresses, is called _________of flange of the T-beam (a) Length (b) Breadth (c) Thickness (d) Depth

Last Answer : (b) Breadth

The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Description : The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Last Answer : [ C ] One-eighth

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

If d is the thickness of a concrete pavement, the equivalent radius b of resisting section for an interior loading, is (A) b = d 2 ) - 0.675 d (B) b = d 2 ) + 0.675 d (C) b = d 2 ) - 3.675 d (D) b = d 2 ) - 0.675 d

Description : If d is the thickness of a concrete pavement, the equivalent radius b of resisting section for an interior loading, is (A) b = d 2 ) - 0.675 d (B) b = d 2 ) + 0.675 d (C) b = d 2 ) - 3.675 d (D) b = d 2 ) - 0.675 d

Last Answer : Answer: Option D

A flat slab is supported (A) On beams (B) On columns (C) On beams and columns (D) On columns monolithically built with slab

Description : A flat slab is supported (A) On beams (B) On columns (C) On beams and columns (D) On columns monolithically built with slab

Last Answer : Answer: Option D

The effective width of a column strip of a flat slab, is (A) One-fourth the width of the panel (B) Half the width of the panel (C) Radius of the column (D) Diameter of the column

Description : The effective width of a column strip of a flat slab, is (A) One-fourth the width of the panel (B) Half the width of the panel (C) Radius of the column (D) Diameter of the column

Last Answer : Answer: Option B

The diameter of the column head support a flat slab, is generally kept (A) 0.25 times the span length (B) 0.25 times the diameter of the column (C) 4.0 cm larger than the diameter of the column (D) 5.0 cm larger than the diameter of the column

Description : The diameter of the column head support a flat slab, is generally kept (A) 0.25 times the span length (B) 0.25 times the diameter of the column (C) 4.0 cm larger than the diameter of the column (D) 5.0 cm larger than the diameter of the column

Last Answer : Option A

If the size of panel in a flat slab is 6 m × 6 m, then as per Indian Standard Code, the widths of column strip and middle strip are (A) 3.0 m and 1.5 m (B) 1.5 m and 3.0 m (C) 3.0 m and 3.0 m (D) 1.5 m and 1.5m

Description : If the size of panel in a flat slab is 6 m × 6 m, then as per Indian Standard Code, the widths of column strip and middle strip are (A) 3.0 m and 1.5 m (B) 1.5 m and 3.0 m (C) 3.0 m and 3.0 m (D) 1.5 m and 1.5 m

Last Answer : Answer: Option C

Reinforced concrete slab supported only on columns is said to be [ A ] Rigid slab [ B ] Flat slab [ C ] Both(a) and (b) [ D ] None of the above.

Description : Reinforced concrete slab supported only on columns is said to be [ A ] Rigid slab [ B ] Flat slab [ C ] Both(a) and (b) [ D ] None of the above.

Last Answer : [ B ] Flat slab

The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

According to IS: 456-2000, the span/overall depth ratio for a continuous two-way slab in order to control deflection is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40

Description : According to IS: 456-2000, the span/overall depth ratio for a continuous two-way slab in order to control deflection is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40

Last Answer : [ C ] 32

The average age of K and L is 48 years. If M replaced K, the average age would be 40 and if M replaced L, the average would be 44. What are the ages of K,L,M repectively? A) 58, 46, 22 B) 32, 44, 36 C) 52,44,36 D) 56, 22,38

Description :  The average age of K and L is 48 years. If M replaced K, the average age would be 40 and if M replaced L, the average would be 44. What are the ages of K,L,M repectively? A) 58, 46, 22 B) 32, 44, 36 C) 52,44,36 D) 56, 22,38

Last Answer : Answer: C)  Total age of K& L = 48*2 = 96 yrs----->1 Total age of L& M = 40*2 = 80yrs----->2 Total age of K& M = 44*2 = 88 yrs----->3 from 1, 2, 3 K+L+M =132---->4 from 1 & 4, M= 36 from 2 & 4, K=52 from 3 & 4, L=44 Hence the required answer is 52,44,36 

If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured parallel to the supported edge, the effective width of the slab be is (A) K/x (1 + x/d) + bw (B) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above

Description : If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured ... ) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above

Last Answer : Answer: Option B

If At is the area of steel cross-section, t is working stress, L is width of road and W is weight of slab per square metre, the spacing of the tie bars for a longitudinal joint, is (A) (100 At × t)/WL (B) 100 At/tWL (C) (100 WAt × t)/tL (D) 100 WL/At t

Description : If At is the area of steel cross-section, t is working stress, L is width of road and W is weight of slab per square metre, the spacing of the tie bars for a longitudinal joint, is (A) (100 At × t)/WL (B) 100 At/tWL (C) (100 WAt × t)/tL (D) 100 WL/At t

Last Answer : Answer: Option D

Would you help me gather ideas to help me hang flat wood panels on the wall?

Description : Would you help me gather ideas to help me hang flat wood panels on the wall?

Last Answer : Use paneling glue on the back and on the wall, then put up on the wall. Once in place tack it down with finishing nails.

A dielectric slab of thickness `d` is inserted in a parallel plate capacitor whose negative plate is at `x = 0` and positive plate is at `x = 3d`. The

Description : A dielectric slab of thickness `d` is inserted in a parallel plate capacitor whose negative plate is at `x = 0` and positive plate is at `x = 3d`. The

Last Answer : A dielectric slab of thickness `d` is inserted in a parallel plate capacitor whose negative plate ... at fist, then decreases and again increase.

A travelling microscope is focussed on a mark made on a paper. When a slab of `1.45cm` thickness is placed on the marl, the microscope has to be raise

Description : A travelling microscope is focussed on a mark made on a paper. When a slab of `1.45cm` thickness is placed on the marl, the microscope has to be raise

Last Answer : A travelling microscope is focussed on a mark made on a paper. When a slab of `1.45cm` ... the mark again. Calculate the refractive index of glass.

The left face of a one dimensional slab of thickness 0.2 m is maintained at 80°C and the right face is exposed to air at 30°C. The thermal conductivity of the slab is 1.2 W/m.K and the heat transfer co-efficient from the right face is 10 W/m2 .K. At steady state, the temperature of the right face in °C is (A) 77.2 (B) 71.2 (C) 63.8 (D) 48.7

Description : The left face of a one dimensional slab of thickness 0.2 m is maintained at 80°C and the right face is exposed to air at 30°C. The thermal conductivity of the slab is 1.2 W/m.K and the heat transfer co-efficient from the ... temperature of the right face in °C is (A) 77.2 (B) 71.2 (C) 63.8 (D) 48.7

Last Answer : (D) 48.7

The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Description : The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Last Answer : (d) 16 t

The toe projection of foundation slabs is taken (A) As one third of the base (B) As one sixth of overall height of the wall (C) Equal to heel slab (D) Below ground surface

Description : The toe projection of foundation slabs is taken (A) As one third of the base (B) As one sixth of overall height of the wall (C) Equal to heel slab (D) Below ground surface

Last Answer : Answer: Option A

The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Last Answer : Answer: Option B

For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm

Description : For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm

Last Answer : (B) 75 mm

The minimum cover in a slab should neither be less than the diameter of bar nor less than (A) 10 mm (B) 15 mm (C) 25 mm (D) 13 m

Description : The minimum cover in a slab should neither be less than the diameter of bar nor less than (A) 10 mm (B) 15 mm (C) 25 mm (D) 13 mm

Last Answer : Answer: Option B

For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm

Description : For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm

Last Answer : (a) 120 mm

Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively, are (a) 10, 15, 20 and 25 (b) 15, 25, 40 and 75 (c ) 20, 25, 30 and 40 (d) 20, 35, 40 and 75

Description : Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively, are (a) 10, 15, 20 and 25 (b) 15, 25, 40 and 75 (c ) 20, 25, 30 and 40 (d) 20, 35, 40 and 75

Last Answer : (b) 15, 25, 40 and 75