Minimum steel required in slabs is mainly controlled by the following consideration [ A ] Cracking on the tension side [ B ] Shrinkage and creep [ C ] Both (a) and (b) [ D ] None of the above.

Minimum steel required in slabs is mainly controlled by the following consideration
[ A ] Cracking on the tension side
[ B ] Shrinkage and creep
[ C ] Both (a) and (b)
[ D ] None of the above.
by

1 Answer

Answer :

[ B ] Shrinkage and creep
by

Related questions

If C is creep coefficient, f is original pre-stress in concrete, m is modular ratio, E is Young's modulus of steel and e is shrinkage strain, the combined effect of creep and shrinkage is: (A) (1 - C)mf - eEB) (C - 1)mf + eE(C) (C - 1)mf - eE(D) (1 - C)mf + eE

Description : If C is creep coefficient, f is original pre-stress in concrete, m is modular ratio, E is Young's modulus of steel and e is shrinkage strain, the combined effect of creep and shrinkage is: (A) (1 - C)mf - eE B) (C - 1)mf + eE (C) (C - 1)mf - eE (D) (1 - C)mf + eE

Last Answer : Answer: Option B

The minimum percentage of tension steel is mainly based on the [ A ] Total depth [ B ] Effective depth [ C ] Both (a) and (b) [ D ] None of the above.

Description : The minimum percentage of tension steel is mainly based on the [ A ] Total depth [ B ] Effective depth [ C ] Both (a) and (b) [ D ] None of the above.

Last Answer : [ A ] Total depth

After pre-stressing process is completed, a loss of stress is due to (A) Shrinkage of concrete (B) Elastic shortening of concrete (C) Creep of concrete (D) All the above

Description : After pre-stressing process is completed, a loss of stress is due to (A) Shrinkage of concrete (B) Elastic shortening of concrete (C) Creep of concrete (D) All the above

Last Answer : Answer: Option D

Which of the following losses of pre-stress occurs only in pre-tensioning and not in posttensioning? (A) Elastic shortening of concrete (B) Shrinkage of concrete (C) Creep of concrete (D) Loss due to frictio

Description : Which of the following losses of pre-stress occurs only in pre-tensioning and not in posttensioning? (A) Elastic shortening of concrete (B) Shrinkage of concrete (C) Creep of concrete (D) Loss due to friction

Last Answer : Answer: Option A

The lower water cement ratio in concrete, introduces (A) Smaller creep and shrinkage (B) Greater density and smaller permeability (C) Improved frost resistance (D) All the above

Description : The lower water cement ratio in concrete, introduces (A) Smaller creep and shrinkage (B) Greater density and smaller permeability (C) Improved frost resistance (D) All the above

Last Answer : Answer: Option D

Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is proportional to the age of the member at the time of loading. (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members

Description : Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is ... to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members

Last Answer : (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete

Slump cone test is used to determine [ A ] Shrinkage of concrete mix [ B ] Creep of concrete [ C ] Workability of concrete mix [ D ] Soundness of concrete

Description : Slump cone test is used to determine [ A ] Shrinkage of concrete mix [ B ] Creep of concrete [ C ] Workability of concrete mix [ D ] Soundness of concrete

Last Answer : [ C ] Workability of concrete mix

The process of keeping the concrete structure moist is called [ A ] Hydration [ B ] Curing [ C ] Creep [ D ] Shrinkage

Description : The process of keeping the concrete structure moist is called [ A ] Hydration [ B ] Curing [ C ] Creep [ D ] Shrinkage

Last Answer : [ B ] Curing

The process of hardening of concrete in the presence of water is called [ A ] Creep [ B ] Hydration [ C ] Shrinkage [ D ] Curing

Description : The process of hardening of concrete in the presence of water is called [ A ] Creep [ B ] Hydration [ C ] Shrinkage [ D ] Curing

Last Answer : [ B ] Hydration

The Minimum percentage of secondary steel in slabs for Fe- 415 grade steel should be __________ of Gross cross-section area [ A ] 0.12% [ B ] 0.15% [ C ] 0.20% [ D ] 0.25%

Description : The Minimum percentage of secondary steel in slabs for Fe- 415 grade steel should be __________ of Gross cross-section area [ A ] 0.12% [ B ] 0.15% [ C ] 0.20% [ D ] 0.25%

Last Answer : [ A ] 0.12%

The presence of sand in brick earth prevents: (A) Cracking of bricks (B) Shrinkage of bricks (C) Warping of bricks (D) None of these

Description : The presence of sand in brick earth prevents: (A) Cracking of bricks (B) Shrinkage of bricks (C) Warping of bricks (D) None of these

Last Answer : Answer: Option C

Sand is mixed with lime to a) Reduced cost b) Reduced setting time c) Prevent shrinkage and cracking* d) Improve visual appearance

Description : Sand is mixed with lime to a) Reduced cost b) Reduced setting time c) Prevent shrinkage and cracking* d) Improve visual appearance

Last Answer : c) Prevent shrinkage and cracking

Consideration of the creep is the most important in case of the (A) Blades of gas turbine (B) Piston of an I. C. engine (C) Flywheel of steam engine (D) Cycle chain

Description : Consideration of the creep is the most important in case of the (A) Blades of gas turbine (B) Piston of an I. C. engine (C) Flywheel of steam engine (D) Cycle chain

Last Answer : (A) Blades of gas turbine

In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Description : In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Last Answer : Answer: Option D

The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Description : The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Last Answer : [ C ] One-eighth

The maximum spacing of main steel in slabs has been limited to [ A ] 250 mm [ B ] 300 mm [ C ] 450 mm [ D ] 500 mm

Description : The maximum spacing of main steel in slabs has been limited to [ A ] 250 mm [ B ] 300 mm [ C ] 450 mm [ D ] 500 mm

Last Answer : [ B ] 300 mm

The percentage of minimum reinforcement of the gross sectional area in slabs, is (A) 0.10 % (B) 0.12 % (C) 0.15 % (D) 0.18 %

Description : The percentage of minimum reinforcement of the gross sectional area in slabs, is (A) 0.10 % (B) 0.12 % (C) 0.15 % (D) 0.18 %

Last Answer : Answer: Option C

Vertical construction joints are provided where the shearing forces are minimum in the case of (A) Slabs (B) Beams (C) Girders (D) All of these

Description : Vertical construction joints are provided where the shearing forces are minimum in the case of (A) Slabs (B) Beams (C) Girders (D) All of these

Last Answer : Answer: Option D

Minimum reinforcement in slabs, when High yield strength deformed bars [ A ] 0.12% of gross cross sectional area [ B ] 0.15% of gross cross sectional area [ C ] 0.20% of gross cross sectional area [ D ] 0.25% of gross cross sectional area.

Description : Minimum reinforcement in slabs, when High yield strength deformed bars [ A ] 0.12% of gross cross sectional area [ B ] 0.15% of gross cross sectional area [ C ] 0.20% of gross cross sectional area [ D ] 0.25% of gross cross sectional area.

Last Answer : [ A ] 0.12% of gross cross sectional area

Minimum percentage area of tension reinforcement , when the grade of steel is Fe-250 [ A ] 0.2 [ B ] 0.25 [ C ] 0.34 [ D ] 0.44

Description : Minimum percentage area of tension reinforcement , when the grade of steel is Fe-250 [ A ] 0.2 [ B ] 0.25 [ C ] 0.34 [ D ] 0.44

Last Answer : [ C ] 0.34

Minimum percentage of tension steel for a singly reinforced section Fe415 grade is [ A ] 0.2 [ B ] 0.35 [ C ] 2 [ D ] 3.5

Description : Minimum percentage of tension steel for a singly reinforced section Fe415 grade is [ A ] 0.2 [ B ] 0.35 [ C ] 2 [ D ] 3.5

Last Answer : [ A ] 0.2

Minimum percentage of tension steel for a singly reinforced section Fe415 grade is [ A ] 0.2 [ B ] 0.35 [ C ] 2 [ D ] 3.5

Description : Minimum percentage of tension steel for a singly reinforced section Fe415 grade is [ A ] 0.2 [ B ] 0.35 [ C ] 2 [ D ] 3.5

Last Answer : [ A ] 0.2

Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low interfacial tension (C) When Henry's law constant is very small, then the mass transfer rate is controlled by the gas film resistance (D) Taylor-Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Description : Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low ... Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Last Answer : (A) Mechanical agitation is required, if the system has low interfacial tension

The minimum water content at which the soil retains its liquid state and also possesses a small shearing strength against flowing, is known (A) Liquid limit (B) Plastic limit (C) Shrinkage limit (D) Permeability limit

Description : The minimum water content at which the soil retains its liquid state and also possesses a small shearing strength against flowing, is known (A) Liquid limit (B) Plastic limit (C) Shrinkage limit (D) Permeability limit

Last Answer : (A) Liquid limit

The minimum water content at which the soil just begins to crumble when rolled into threads 3 mm in diameter, is known (A) Liquid limit (B) Plastic limit (C) Shrinkage limit (D) Permeability limit

Description : The minimum water content at which the soil just begins to crumble when rolled into threads 3 mm in diameter, is known (A) Liquid limit (B) Plastic limit (C) Shrinkage limit (D) Permeability limit

Last Answer : (B) Plastic limit

Minimum shear reinforcement is necessary to [ A ] Prevent brittle shear failure [ B ] Prevent failure due to shrinkage and thermal stresses [ C ] Hold the reinforcements in place while pouring concrete [ D ] All the above.

Description : Minimum shear reinforcement is necessary to [ A ] Prevent brittle shear failure [ B ] Prevent failure due to shrinkage and thermal stresses [ C ] Hold the reinforcements in place while pouring concrete [ D ] All the above.

Last Answer : [ D ] All the above.

If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Last Answer : Answer: Option D

Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach its maximum permissible value first. (c) The moment of resistance will be less than that of the balanced section. (d) The concrete on the tension side is also be considered for calculating the moment of resistance of the section.

Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.

Last Answer : both b&c

Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Description : Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Last Answer : [ B ] point of maximum tension

Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Description : Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Last Answer : [ B ] point of maximum tension

Yield strength of a material is determined by the __________ test. (A) Creep (B) Tension (C) Compression (D) Endurance

Description : Yield strength of a material is determined by the __________ test. (A) Creep (B) Tension (C) Compression (D) Endurance

Last Answer : Option B

The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending strength and axial yield strength of material (c) Buckling strength based on the net area of the section and percentage elongation at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Description : The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending ... at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Last Answer : (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

For ductility consideration, the maximum percentage of steel used should not exceed ------- of the balanced steel [ A ] 25% [ B ] 50% [ C ] 60% [ D ] 75%

Description : For ductility consideration, the maximum percentage of steel used should not exceed ------- of the balanced steel [ A ] 25% [ B ] 50% [ C ] 60% [ D ] 75%

Last Answer : [ D ] 75%

Presence of high concentration of ozone and smog in atmospheric air causes the(A) Embrittlement & decrease of folding resistance of paper(B) Cracking of rubber products(C) Fading of dye on textiles(D) Damage of electrical insulator on high tension power line

Description : Presence of high concentration of ozone and smog in atmospheric air causes the (A) Embrittlement & decrease of folding resistance of paper (B) Cracking of rubber products (C) Fading of dye on textiles (D) Damage of electrical insulator on high tension power line

Last Answer : (B) Cracking of rubber products

Soaking pits are meant for heating steel (A) Ingots (B) Coils (C) Sheets (D) Slabs

Description : Soaking pits are meant for heating steel (A) Ingots (B) Coils (C) Sheets (D) Slabs

Last Answer : (A) Ingots

Reheating furnace (pusher type) is used for heating (A) Ingots (B) Slabs (C) Steel coils (D) Steel sheets

Description : Reheating furnace (pusher type) is used for heating (A) Ingots (B) Slabs (C) Steel coils (D) Steel sheets

Last Answer : (B) Slabs

Coke oven gas after passing through return electrostatic tar precipitator (RETP) is used for the (A) Hot scarfing of steel slabs (B) Mixing with blast furnace gas (C) Coke oven battery heating (D) Steel ladle drying

Description : Coke oven gas after passing through return electrostatic tar precipitator (RETP) is used for the (A) Hot scarfing of steel slabs (B) Mixing with blast furnace gas (C) Coke oven battery heating (D) Steel ladle drying

Last Answer : (C) Coke oven battery heating

Cracking of ceramic articles can be controlled by non-clay materials like

Description : Cracking of ceramic articles can be controlled by non-clay materials like

Last Answer : flint/quartz.

How can cracking of ceramic articles be controlled?

Description : How can cracking of ceramic articles be controlled?

Last Answer : Cracking of ceramic articles can be controlled if non-clay materials like flint and quartz are added to the mixture.

If q is the punching shear resistance per unit area a, is the side of a square footing for a column of side b, carrying a weight W including the weight of the footing, the depth (D) of the footing from punching shear consideration, is (A) D = W (a - b)/4a²bq (B) D = W (a² - b²)/4a²bq (C) D = W (a² - b²)/8a²bq (D) D = W (a² - b²)/4abq

Description : If q is the punching shear resistance per unit area a, is the side of a square footing for a column of side b, carrying a weight W including the weight of the footing, the depth (D) of the footing from punching shear consideration ... - b²)/4a²bq (C) D = W (a² - b²)/8a²bq (D) D = W (a² - b²)/4abq

Last Answer : Answer: Option B

In a singly reinforced concrete beam, as the load increases. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete and steel will resist tension. (d) Both concrete and steel will resist compression.

Description : In a singly reinforced concrete beam, as the load increases. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete and steel will resist tension. (d) Both concrete and steel will resist compression.

Last Answer : (b) Only steel bars will resist tension.

In a singly reinforced concrete beam, if the load is vey small. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete & steel will resist tension. (d) Both concrete & steel will resist compression.

Description : In a singly reinforced concrete beam, if the load is vey small. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete & steel will resist tension. (d) Both concrete & steel will resist compression.

Last Answer : (c) Both concrete & steel will resist tension.

Presence of manganese in alloy steel improves its (A) Corrosion resistance (B) Cutting ability (C) Abrasion resistance & toughness (D) Elasticity & creep resistance

Description : Presence of manganese in alloy steel improves its (A) Corrosion resistance (B) Cutting ability (C) Abrasion resistance & toughness (D) Elasticity & creep resistance

Last Answer : (C) Abrasion resistance & toughness

The catalytic cracking of heavier petroleum fraction is done to produce mainly (A) Gasoline (B) Asphalt (C) Diesel oil (D) Tar

Description : The catalytic cracking of heavier petroleum fraction is done to produce mainly (A) Gasoline (B) Asphalt (C) Diesel oil (D) Tar

Last Answer : (C) Diesel oil

Though increased pressure has a retarding effect on cracking reaction, yet in actual process, a positive pressure of 10-15 kgf/cm2 is maintained during cracking mainly to (A) Increase the yield of light distillates (B) Suppress coke formation (C) Enhance the octane number of gasoline (D) Reduce gum content in gasoline

Description : Though increased pressure has a retarding effect on cracking reaction, yet in actual process, a positive pressure of 10-15 kgf/cm2 is maintained during cracking mainly to (A) Increase the yield of ... coke formation (C) Enhance the octane number of gasoline (D) Reduce gum content in gasoline

Last Answer : (B) Suppress coke formation

The minimum water content at which a reduction in water content will not cause a decrease in the volume of a soil mass is known as a) Plastic limit b) Shrinkage limit* c) Liquid limit d) Consistency limit

Description : The minimum water content at which a reduction in water content will not cause a decrease in the volume of a soil mass is known as a) Plastic limit b) Shrinkage limit* c) Liquid limit d) Consistency limit

Last Answer : b) Shrinkage limit*

Which of the following is an example of stress corrosion? (A) Season cracking of brass (B) Caustic embrittlement of steel (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Which of the following is an example of stress corrosion? (A) Season cracking of brass (B) Caustic embrittlement of steel (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : Option C

The toe projection of foundation slabs is taken (A) As one third of the base (B) As one sixth of overall height of the wall (C) Equal to heel slab (D) Below ground surface

Description : The toe projection of foundation slabs is taken (A) As one third of the base (B) As one sixth of overall height of the wall (C) Equal to heel slab (D) Below ground surface

Last Answer : Answer: Option A

According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is (A) Half of the width of the slab (B) Two-third of the width of the slab (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Last Answer : Answer: Option C

The concrete work for the following part of the building of specified thickness is measured in square metres (A) Root slabs (B) Floors (C) Wall panels (D) All the above

Description : The concrete work for the following part of the building of specified thickness is measured in square metres (A) Root slabs (B) Floors (C) Wall panels (D) All the above

Last Answer : (D) All the above