Reheating furnace (pusher type) is used for heating (A) Ingots (B) Slabs (C) Steel coils (D) Steel sheets

Reheating furnace (pusher type) is used for heating
(A) Ingots
(B) Slabs
(C) Steel coils
(D) Steel sheets
by

1 Answer

Answer :

(B) Slabs
by

Related questions

Soaking pits are meant for heating steel (A) Ingots (B) Coils (C) Sheets (D) Slabs

Description : Soaking pits are meant for heating steel (A) Ingots (B) Coils (C) Sheets (D) Slabs

Last Answer : (A) Ingots

An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth

Description : An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth

Last Answer : (A) Walking beam

Coke oven gas after passing through return electrostatic tar precipitator (RETP) is used for the (A) Hot scarfing of steel slabs (B) Mixing with blast furnace gas (C) Coke oven battery heating (D) Steel ladle drying

Description : Coke oven gas after passing through return electrostatic tar precipitator (RETP) is used for the (A) Hot scarfing of steel slabs (B) Mixing with blast furnace gas (C) Coke oven battery heating (D) Steel ladle drying

Last Answer : (C) Coke oven battery heating

Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola

Description : Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola

Last Answer : (B) Reheating furnace

The heating capacity of continuous reheating furnace depends upon the (A) Hearth area and furnace temperature (B) Emissivity of the stock (C) Ratio of wall surface to stock surface (D) All (A), (B) and (C)

Description : The heating capacity of continuous reheating furnace depends upon the (A) Hearth area and furnace temperature (B) Emissivity of the stock (C) Ratio of wall surface to stock surface (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85

Description : The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85

Last Answer : (B) 40

Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating

Description : Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating

Last Answer : (A) Cold rolled steel coil annealing

Height of coke oven is limited (say maximum upto 7 metres) mainly by the(A) Problem of uniform heating along its height(B) Structural strength of silica bricks(C) Problem in door cleaning(D) Buckling of ram of pusher car at the time of coke pushing

Description : Height of coke oven is limited (say maximum upto 7 metres) mainly by the (A) Problem of uniform heating along its height (B) Structural strength of silica bricks (C) Problem in door cleaning (D) Buckling of ram of pusher car at the time of coke pushing

Last Answer : (A) Problem of uniform heating along its height

Width of the coke oven towards coke side is slightly more than that on pusher side to (A) Facilitate easy discharging of coke as it swells during carbonisation (B) Facilitate uniform heating of the oven (C) Increase the output of the coke (D) None of these

Description : Width of the coke oven towards coke side is slightly more than that on pusher side to (A) Facilitate easy discharging of coke as it swells during carbonisation (B) Facilitate uniform heating of the oven (C) Increase the output of the coke (D) None of these

Last Answer : (A) Facilitate easy discharging of coke as it swells during carbonisation

Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns

Description : Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns

Last Answer : (C) Boiler furnace

An example of indirectly heated furnace is the (A) Soaking pit (B) Muffle furnace (C) Reheating furnace (D) None of these

Description : An example of indirectly heated furnace is the (A) Soaking pit (B) Muffle furnace (C) Reheating furnace (D) None of these

Last Answer : (B) Muffle furnace

Which of the following is a heat treatment furnace? (A) Muffle furnace (B) Annealing furnace (C) Reheating furnace (D) Rotary kiln

Description : Which of the following is a heat treatment furnace? (A) Muffle furnace (B) Annealing furnace (C) Reheating furnace (D) Rotary kiln

Last Answer : (B) Annealing furnace

Which is the most thermally efficient furnace? (A) Reheating furnace (B) Reverberatory furnace (C) Rotary kilns (D) Boiler furnace

Description : Which is the most thermally efficient furnace? (A) Reheating furnace (B) Reverberatory furnace (C) Rotary kilns (D) Boiler furnace

Last Answer : (D) Boiler furnace

__________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace

Description : __________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace

Last Answer : (B) Muffle furnace

Which of the following is a periodic furnace? (A) Tunnel kiln (B) Rotary kiln (C) Soaking pit (D) Reheating furnace

Description : Which of the following is a periodic furnace? (A) Tunnel kiln (B) Rotary kiln (C) Soaking pit (D) Reheating furnace

Last Answer : (C) Soaking pit

Which of the following is a directly fired intermittent furnace? (A) Walking beam reheating furnace (B) Reverberatory furnace (C) Tower furnace (D) Tunnel kiln

Description : Which of the following is a directly fired intermittent furnace? (A) Walking beam reheating furnace (B) Reverberatory furnace (C) Tower furnace (D) Tunnel kiln

Last Answer : (B) Reverberatory furnace

Which of the following is not a recuperative furnace? (A) Soaking pit (B) Reheating furnace(C) Steam boiler(D) Coke oven

Description : Which of the following is not a recuperative furnace? (A) Soaking pit (B) Reheating furnace (C) Steam boiler (D) Coke oven

Last Answer : (D) Coke oven

Which of the following is a batch furnace? (A) Cupola (B) Reheating furnace (C) Glass tank furnace (D) None of these

Description : Which of the following is a batch furnace? (A) Cupola (B) Reheating furnace (C) Glass tank furnace (D) None of these

Last Answer : (A) Cupola

Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor

Description : Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor

Last Answer : compressor

Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Description : Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Last Answer : Billet Reheating Furnace

Apart from feed heating, what should a plant have to obtain a gain in thermal efficiency? a) Lubrication b) Differential heating c) Reheating cycles d) Regenerative cycles

Description : Apart from feed heating, what should a plant have to obtain a gain in thermal efficiency? a) Lubrication b) Differential heating c) Reheating cycles d) Regenerative cycles

Last Answer : c) Reheating cycles

Reverberatory furnace is used for (A) Roasting/reduction of ores (B) Annealing steel coil (C) Heating air (D) Steel melting

Description : Reverberatory furnace is used for (A) Roasting/reduction of ores (B) Annealing steel coil (C) Heating air (D) Steel melting

Last Answer : (A) Roasting/reduction of ores

Which cement should not be used for bridge slabs ro RCC frames a) OPC b) Portland Pozzolana cement * c) Portland furnace slag cement d) Rapid hardening cement

Description : Which cement should not be used for bridge slabs ro RCC frames a) OPC b) Portland Pozzolana cement * c) Portland furnace slag cement d) Rapid hardening cement

Last Answer : b) Portland Pozzolana cement *

How much would it cost to buy a treasure chest filled with Canadian quarters and other coins and metal ingots?

Description : How much would it cost to buy a treasure chest filled with Canadian quarters and other coins and metal ingots?

Last Answer : answer:How large would the treasure chest be? 10” x 10” would hold significantly less than 2’ x 3’

Where can one buy physical copper and other cheap metal ingots in Canada?

Description : Where can one buy physical copper and other cheap metal ingots in Canada?

Last Answer : Lead is non-toxic? Anyway, have you tried metal scrappers? Once the metal is scrapped and melted down, they must press it at some point for resale. If you’re looking for pure metal, a scientific supply house would be your best bet.

The Minimum percentage of secondary steel in slabs for Fe- 415 grade steel should be __________ of Gross cross-section area [ A ] 0.12% [ B ] 0.15% [ C ] 0.20% [ D ] 0.25%

Description : The Minimum percentage of secondary steel in slabs for Fe- 415 grade steel should be __________ of Gross cross-section area [ A ] 0.12% [ B ] 0.15% [ C ] 0.20% [ D ] 0.25%

Last Answer : [ A ] 0.12%

Minimum steel required in slabs is mainly controlled by the following consideration [ A ] Cracking on the tension side [ B ] Shrinkage and creep [ C ] Both (a) and (b) [ D ] None of the above.

Description : Minimum steel required in slabs is mainly controlled by the following consideration [ A ] Cracking on the tension side [ B ] Shrinkage and creep [ C ] Both (a) and (b) [ D ] None of the above.

Last Answer : [ B ] Shrinkage and creep

The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Description : The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Last Answer : [ C ] One-eighth

The maximum spacing of main steel in slabs has been limited to [ A ] 250 mm [ B ] 300 mm [ C ] 450 mm [ D ] 500 mm

Description : The maximum spacing of main steel in slabs has been limited to [ A ] 250 mm [ B ] 300 mm [ C ] 450 mm [ D ] 500 mm

Last Answer : [ B ] 300 mm

How to connect two heating coils to three 400V phases?

Description : Hello. I need to connect two heating coils to three 400V phases. Don't know how? Thank you

Last Answer : Need Answer

what is a bathtr 1410000c heating coils go too

Description : what is a bathtr 1410000c heating coils go too

Last Answer : Need Answer

Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Description : Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Last Answer : Parts Insulating Materials  Insulation between heating element and base plate of electric iron. Mica Insulation used over copper or aluminium conductor used for making coils.  ... Transformer bushings Porcelain  Insulation between transmission line and pole. Porcelain

Are you a button pusher?

Description : Are you a button pusher?

Last Answer : Yes. I love messing around on new phones and figuring out how to customize it.

How do I find out if coin pusher games are legal in Ohio?

Description : How do I find out if coin pusher games are legal in Ohio?

Last Answer : Call the local prosecutor or police?

Many-manned scud-thumper, Maker of worn wood, Shrub-ruster, Sky-mocker, Rave! Portly pusher, Wind-slave.What am I? -Riddles

Description : Many-manned scud-thumper, Maker of worn wood, Shrub-ruster, Sky-mocker, Rave! Portly pusher, Wind-slave.What am I? -Riddles

Last Answer : The ocean!

Rising gradient followed by a falling gradient is known as a) Rulling gradient b) Momentum gradient* c) Pusher graient d) Aangular gradient

Description : Rising gradient followed by a falling gradient is known as a) Rulling gradient b) Momentum gradient* c) Pusher graient d) Aangular gradient

Last Answer : b) Momentum gradient

Steep gradients which need extra engine for hauling is known as a) Pusher gradient* b) Rulling Gradient c) Reasonable gradient d) Momentum gradient

Description : Steep gradients which need extra engine for hauling is known as a) Pusher gradient* b) Rulling Gradient c) Reasonable gradient d) Momentum gradient

Last Answer : a) Pusher gradient

High purity nitrogen is used in (A) Making protective gas (95% N2 + 5% H2 ) for annealing of cold rolled steel strip coils (B) Fire fighting purposes (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : High purity nitrogen is used in (A) Making protective gas (95% N2 + 5% H2 ) for annealing of cold rolled steel strip coils (B) Fire fighting purposes (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Galvanising (i.e., zinc coating) of steel sheets is done to (A) Prevent its rusting by contact with corrosive atmosphere (B) Protect the base metal by cathodic protection (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Galvanising (i.e., zinc coating) of steel sheets is done to (A) Prevent its rusting by contact with corrosive atmosphere (B) Protect the base metal by cathodic protection (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The process of coating steel sheets by zinc to improve its corrosion resistance is called (A) Calorising (B) Galvanising (C) Zincification (D) Tempering

Description : The process of coating steel sheets by zinc to improve its corrosion resistance is called (A) Calorising (B) Galvanising (C) Zincification (D) Tempering

Last Answer : (B) Galvanising

The main use of HCl is in the (A) Drilling of petroleum wells and pickling of steel sheets (B) Manufacture of cationic detergent (C) Treatment of spent fuel of nuclear reactor (D) None of these

Description : The main use of HCl is in the (A) Drilling of petroleum wells and pickling of steel sheets (B) Manufacture of cationic detergent (C) Treatment of spent fuel of nuclear reactor (D) None of these

Last Answer : (A) Drilling of petroleum wells and pickling of steel sheets

Hearth furnaces are not used for (A) Roasting (B) Melting (C) Reheating (D) None of these

Description : Hearth furnaces are not used for (A) Roasting (B) Melting (C) Reheating (D) None of these

Last Answer : (D) None of these

Air at a particular humidity is heated in a furnace. The new dew point (A) Decreases (B) Increases (C) Depends on the extent of heating (D) Remain unchanged

Description : Air at a particular humidity is heated in a furnace. The new dew point (A) Decreases (B) Increases (C) Depends on the extent of heating (D) Remain unchanged

Last Answer : (B) Increases

The radiation heat flux from a heating element at a temperature of 800°C, in a furnace maintained at 300°C is 8 kW/m2 . The flux, when the element temperature is increased to 1000°C for the same furnace temperature is (A) 11.2 kW/m2(B) 12.0 kW/m2(C) 14.6 kW/m2(D) 16.5 kW/m

Description : The radiation heat flux from a heating element at a temperature of 800°C, in a furnace maintained at 300°C is 8 kW/m2 . The flux, when the element temperature is increased to 1000°C for the same furnace temperature is (A) 11.2 kW/m2 (B) 12.0 kW/m2 (C) 14.6 kW/m2 (D) 16.5 kW/m

Last Answer : (D) 16.5 kW/m2

The resistance furnace produces heat by the (A) Electric arc struck between electrodes and the charge (B) Flow of current through a heating element (C) Combination of induced current and skin effect (D) None of these

Description : The resistance furnace produces heat by the (A) Electric arc struck between electrodes and the charge (B) Flow of current through a heating element (C) Combination of induced current and skin effect (D) None of these

Last Answer : (B) Flow of current through a heating element

In low or standard frequency induction furnace, heat is produced by the (A) Combination of induced current and skin effect (B) Induction and resistance (C) Current flow through a heating element (D) None of these

Description : In low or standard frequency induction furnace, heat is produced by the (A) Combination of induced current and skin effect (B) Induction and resistance (C) Current flow through a heating element (D) None of these

Last Answer : (B) Induction and resistance

Specific heating capacity of a furnace is expressed as (A) Weight heated/hr (B) Weight heated/furnace volume (C) Weight heated/hr/furnace volume (D) None of these

Description : Specific heating capacity of a furnace is expressed as (A) Weight heated/hr (B) Weight heated/furnace volume (C) Weight heated/hr/furnace volume (D) None of these

Last Answer : (C) Weight heated/hr/furnace volume

If the flame is produced under the hearth and then sweeps up into the heating chamber, this is called a/an __________ furnace. (A) Sidefired (B) Underfired (C) Covered (D) Recirculating

Description : If the flame is produced under the hearth and then sweeps up into the heating chamber, this is called a/an __________ furnace. (A) Sidefired (B) Underfired (C) Covered (D) Recirculating

Last Answer : (B) Underfired

Thermal efficiency of blast furnace stoves used for heating blast (air) may be about __________ percent. (A) 20 (B) 40 (C) 60 (D) 80

Description : Thermal efficiency of blast furnace stoves used for heating blast (air) may be about __________ percent. (A) 20 (B) 40 (C) 60 (D) 80

Last Answer : (D) 80

Heat transfer takes place through a liquid medium surrounding the submerged material under heating, in case of a/an (A) Blast furnace (B) Steam boiler (C) Salt bath furnace (D) Annealing furnace

Description : Heat transfer takes place through a liquid medium surrounding the submerged material under heating, in case of a/an (A) Blast furnace (B) Steam boiler (C) Salt bath furnace (D) Annealing furnace

Last Answer : (C) Salt bath furnace