An inverter converts

An inverter converts 

A) d.c. voltage to variable d.c. voltage B) ac. voltage to d.c. voltage C) d.c. voltage to ac. voltage of constant frequency D) d.c. voltage to ac. voltage of variable frequency 
by

2 Answers

Answer :

An inverter converts d.c. voltage to ac. voltage of variable frequency 

by

Answer :

An inverter converts d.c. voltage to a.c. voltage of variable frequency 

by
by
Thanks for your support.
by
Any time.
Good platform
by
Yeah... thanks...

Related questions

The output voltage waveform of a three-phase square-wave inverter contains

Description : The output voltage waveform of a three-phase square-wave inverter contains  (A) only even harmonics (B) both odd and even harmonic (C) only odd harmonics (D) only triple harmonics

Last Answer : C

A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW

Description : A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is  (A) 119.05 A (B) 79.37 A (C) 68.73 A (D) 39.68 A

Last Answer : A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is 68.73 A

A freewheeling diode in a phase controlled converter

Description : A freewheeling diode in a phase controlled converter  A) Deceases the possibility of discontinuous conduction in the load B) Increases the possibility of discontinuous conduction in the load C) Reduces the power factor and causes over voltages D) Causes over voltages

Last Answer : A freewheeling diode in a phase controlled converter Deceases the possibility of discontinuous conduction in the load 

The ripple content of load current of a converter feeding RL load is decided by

Description : The ripple content of load current of a converter feeding RL load is decided by  A) Load resistance alone B) Load inductance alone C) Both load resistance and load inductance D) Neither resistance nor inductance

Last Answer : The ripple content of load current of a converter feeding RL load is decided by Both load resistance and load inductance

A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge

Description : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the dc current at 20 A ... thyristor will be reverse biased for a period of  (A) 125o (B) 120o (C) 60o (D) 55o

Last Answer : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the ... the solar cell resistance is 0.5 Ohm ,then each thyristor will be reverse biased for a period of 125o

A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and

Description : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high load inductance. The input ... 0.552 (C) IDF IPF = = 0.5; 0.478 (D) IDF IPF = = 0.5; 0.318 

Last Answer : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high ... (IDF) and the input power factor (IPF) of the converter will be IDF IPF = = 0.5; 0.478

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave

Description : A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

Last Answer : A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is 1.0 A

A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately

Description : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the ... at half the rated speed is  (A) 0.354 (B) 0.372 (C) 0.90 (D) 0.955

Last Answer : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the losses, the power factor of the ac mains at half the rated speed is 0.354

“Six MOSFETs connected in a bridge configuration (having no other power device) must be operated as a

Description : Six MOSFETs connected in a bridge configuration (having no other power device) must be operated as a Voltage Source Inverter (VSI) . This statement is  (A) True, because being majority ... (D) False, because MOSFETs can be operated as excellent constant current sources in the saturation region.

Last Answer : “Six MOSFETs connected in a bridge configuration (having no other power device) must be operated as a Voltage Source Inverter (VSI)”. This statement is False, because MOSFETs can be operated as excellent constant current sources in the saturation region.

A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the

Description : A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode.  (A) ... to one of the SCRs is missed, it will subsequently cause a high load current in the other SCR.

Last Answer : A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode. because the converter does not provide for free-wheeling for high values of triggering angles

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25 and an

Description : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is  (A) 0.78 (B) 0.827 (C) 0.866 (D) 0.9

Last Answer : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is 0.78

A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load

Description : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component ... (B) 31% and 7.8 A (C) 66% and 6.8 A (D) 66% and 7.8 A

Last Answer : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component of input current will respectively be 31% and 7.8 A

a single phase full wave midpoint thyristor converter uses a 230/200V transformer with centre tap on the

Description : a single phase full wave midpoint thyristor converter uses a 230/200V transformer with centre tap on the secondary side. The P.I.V per thyristor is   (A) 100V (B)141.4V (C)200V (D)282.8V

Last Answer : d

A single phase CSI has capacitor C as the load. For a constant source current, the voltage across the capacitor

Description : A single phase CSI has capacitor C as the load. For a constant source current, the voltage across the capacitor is   (A) square wave (B) triangular wave (C) step function (D) pulsed wave

Last Answer : Step function

A converter which can operate in both 3 pulse and 6 pulse mode is a

Description : A converter which can operate in both 3 pulse and 6 pulse mode is a  (A) 1 phase full converter (B) 3 phase half wave converter (C) 3 phase semi converter (D) 3 phase full converter.

Last Answer : A converter which can operate in both 3 pulse and 6 pulse mode is a 3 phase semi converter

In which type of AC to DC converter efficiency is higher :

Description : In which type of AC to DC converter efficiency is higher :

Last Answer : In which type of AC to DC converter efficiency is higher : solid state rectifier

How do you find power in a circuit?

Description : How do you find power in a circuit?

Last Answer : Power can be find in a circuit by the means of meters .if an individual want to check for a power in a circuit he/she Calabria the meters on a high voltage range and put the meters Lee in parallel with the circuit he /she will know the amount of power within that circuit .

How does a DC to AC inverter work?

Description : How does a DC to AC inverter work?

Last Answer : Start with a switching circuit that supplies the DC with one polarity then reverses the polarity, back and forth. That's done at the target AC frequency. An inverter that's any good will knock ... and will further attempt to smooth the wave to more closely resemble normal AC power from the mains.

What is the load of an AC inverter on a battery?

Description : What is the load of an AC inverter on a battery?

Last Answer : answer:If this is a new inverter, figure it is only 80% efficient. If you are truly drawing 1100 Watts continuously then the inverter is drawing 1375 Watts. You are feeding it with 12 volts Power = ... gas generator. Sorry for the bad news but the most of the laws of physics are difficult to break.

Road Trip ? Crockpot is 265W, 120V and my inverter is 1000w. Will I be ok cooking with it on the road?

Description : Road Trip ? Crockpot is 265W, 120V and my inverter is 1000w. Will I be ok cooking with it on the road?

Last Answer : Inverter will be OK. Will you be running off the battery, or while driving? You don't want a dead battery. Continuous output of 265W means it will use 530W of battery power every hour. 12V x ... Compare that to 530 WattHour for the inverter and you can figure out how many hours to a dead battery.

What is plc inverter?

Description : What is plc inverter?

Last Answer : This allows the 3G3MV increased intelligence and autonomy for tasks such as positioning and synchronization. Combining the inverter and PLC eliminates the cost and delay of point-to- ... enhanced speed, positioning and function control for the application being controlled. See More industrialstorebd

Which gate is used as inverter ?

Description : Which gate is used as inverter ?

Last Answer : NOT gate is used as inverter .

What is an inverter ?

Description : What is an inverter ?

Last Answer : A special kind of logic circuit. If a high quality signal is given at the input of this circuit then a low quality signal is received at the output , it is called inverter.

Otp shows then disconnect's in zelio sine wave inverter luminous 1600va?

Description : Otp shows then disconnect's in zelio sine wave inverter luminous 1600va?

Last Answer : Need Answer

What is otp error code in my luminous Zelio+1100 inverter and what is solution for this?

Description : What is otp error code in my luminous Zelio+1100 inverter and what is solution for this?

Last Answer : Install a plastic window that can resist this air and once you do that make sure to check the information before getting in in your computer what do you want by phone

Why my inverter is switching on and off in every second?

Description : Why my inverter is switching on and off in every second?

Last Answer : An inverter switching on and off means it is either getting tripped or the relay function is faulty. This may happen due to many reasons such as Fully discharged battery One or more battery is faulty ... discharged battery is the culprit. If so you have to charge the battery by any other means.

What to do when inverter battery is fully discharged?

Description : What to do when inverter battery is fully discharged?

Last Answer : If the inverter battery is fully discharged then the inverter or UPS should put to OFF position and charge the inverter for enough time before putting it ON again. If the inverter is unable to charge the battery then you may charge it using another charger or inverter. Then connect it back again.

Do the inverter battery get charged in bypass mode?

Description : Do the inverter battery get charged in bypass mode?

Last Answer : Battery charger won't work when an home UPS or inverter is in bypass mode. Bypass switch is used to bypass the input directly to the output whenever a fault occurs in the inverter / ... is to check the voltage and charge both batteries individually using a charger or single battery inverter.

My luminous inverter zelio 900VA showing error code Cbl what is this code for?

Description : My luminous inverter zelio 900VA showing error code Cbl what is this code for?

Last Answer : Cbl code on your inverter is 'check output cable' indication. This is an error code for wrong output cable connection. If you find a Cbl code on your inverter display then you have to check the output cable connection. Don't run your inverter with wrong or loose connections.

What is btp error code in luminous zelio inverter?

Description : What is btp error code in luminous zelio inverter?

Last Answer : The btp error code in inverters describes that the mains input MCB on the inverter is tripped so as to protect the device from a short circuit or lightening. During this error the inverter will be in ... cases btp error may even lead to a board complaint if the MCB couldn't protect the inverter.

Which variable frequency drive should I use for a 1.5 ton inverter AC?

Description : Which variable frequency drive should I use for a 1.5 ton inverter AC?

Last Answer : You do not need to use an external variable frequency drive for the said AC. You have mentioned that it is inverter AC. It means the AC is already fitted with a built in ... / compressor depending upon the room condition, external temperature, temperature setting etc. It is little complicated.

Benefits of Using a DC Inverter During Road Trips?

Description : Benefits of Using a DC Inverter During Road Trips?

Last Answer : The average person cannot identify a DC inverter simply by looking at one. However, most drivers do know what purpose these small devices serve. These inverters plug into a vehicle's DC outlet and ... should always consider going out and buying one of these little units for their next road trip.

Why You Need a Power Inverter?

Description : Why You Need a Power Inverter?

Last Answer : A power inverter is a great tool to have in an emergency. Power inverters plug into the cigarette lighter of your car to charge. They allow you to plug in and run your every day household electrics ... to plug in your coffee pot and microwave so that you have small cooking sources during an outage.

Should I Buy a Modified or Pure Sine Wave Inverter?

Description : Should I Buy a Modified or Pure Sine Wave Inverter?

Last Answer : Many people are unsure of the differences between a modified or pure sine wave inverter. Think of a modified sine wave inverter as a set of stairs. You will get power in blocks and there will be times ... to draw a lot of power should always be run on a sine wave inverter for consistency and safety.

Which is the best inverter air conditioner?

Description : Which is the best inverter air conditioner?

Last Answer : It depends not only the Brand also the technology that Brands are using in it.First thing is CompressorT3 compressorand the compressor who can work in 60 C temperature.After this ERR must grater than 3.8, recommended 4.0.International Brand Sharp ac and Kenwood Acs are best. Recommended Kenwood

A transformer works on the principle of – (1) Self induction (2) Mutual induction (3) Generator (4) Inverter

Description : A transformer works on the principle of – (1) Self induction (2) Mutual induction (3) Generator (4) Inverter

Last Answer : (2) Mutual induction

What type of circuit is on card 'A0AA2' at coordinate '29Q' shown in the illustration? EL-0099 A. Operational amplifier B. Digital logic inverter C. Square wave pulse generator D. Binary counter

Description : What type of circuit is on card 'A0AA2' at coordinate '29Q' shown in the illustration? EL-0099 A. Operational amplifier B. Digital logic inverter C. Square wave pulse generator D. Binary counter

Last Answer : Answer: A

The sensor connected to 'signal conditioner' (6000F125) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Description : The sensor connected to 'signal conditioner' (6000F125) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Last Answer : Answer: B

The sensor connected to 'signal conditioner' (6000AH170) shown in the illustration is a/an _____________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Description : The sensor connected to 'signal conditioner' (6000AH170) shown in the illustration is a/an _____________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Last Answer : Answer: A

The sensor connected to 'signal conditioner' (6000F085) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Description : The sensor connected to 'signal conditioner' (6000F085) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Last Answer : Answer: D

What’s the one main difference between UPS & inverter?

Description : What’s the one main difference between UPS & inverter?

Last Answer : Uninterrupted power supply is mainly use for short time. Means according to ups VA it gives backup. ups is also two types : on line and offline . Online ups having high volt and amp for long time ... inverter is start with 12v,24,dc to 36v dc and 120amp to 180amp battery with long time backup.

What Is The One Main Difference Between Ups & Inverter ? And Electrical Engineering & Electronics Engineering ?

Description : What Is The One Main Difference Between Ups & Inverter ? And Electrical Engineering & Electronics Engineering ?

Last Answer : uninterrupted power supply is mainly use for short time .me according to ups VA it gives backup. ups is also two types : on line. offline. online ups having high volt and amp for long time backup ... but inverter is start with 2v,24,dc to 36v dc and 20amp to 80amp battery with long time backup.

What are the disadvantages of the harmonics present in the inverter system?

Description : What are the disadvantages of the harmonics present in the inverter system?

Last Answer : a. Harmonic currents will lead to excessive heating in the induction motors. This will reduce the load carrying capacity of the motor. b. If the control and the regulating circuits are not ... affected. d. On critical loads, torque pulsation produced by the harmonic current can be useful.

What is meant by McMurray inverter?

Description : What is meant by McMurray inverter?

Last Answer : It is an impulse commutated inverter which relies on LC circuit and an auxiliary thyristor for commutation in the load circuit.

How is the inverter circuit classified based on commutation circuitry?

Description : How is the inverter circuit classified based on commutation circuitry?

Last Answer : a. Line commutated inverters. b. Load commutated inverters. c. Self commutated inverters. d. Forced commutated inverters.

What are the applications of a series inverter?

Description : What are the applications of a series inverter?

Last Answer : The thyristorised series inverter produces an approximately sinusoidal waveform at a high output frequency, ranging from 200 Hz to 100kHz. It is commonly used for fixed output applications such as a. Ultrasonic generator. b. Induction heating. c. Sonar Transmitter d. Fluorescent lighting.

What is meant a parallel inverter?

Description : What is meant a parallel inverter?

Last Answer : An inverter in which the commutating elements are connected in parallel with the load is called a parallel inverter.

What is the condition to be satisfied in the selection of L and C in a series inverter?

Description : What is the condition to be satisfied in the selection of L and C in a series inverter?

Last Answer : R2< 4LC

What is meant a series inverter?

Description : What is meant a series inverter?

Last Answer : An inverter in which the commutating elements are connected in series with the load is called a series inverter.

Why diodes should be connected in antiparallel with the thyristors in inverter circuits?

Description : Why diodes should be connected in antiparallel with the thyristors in inverter circuits?

Last Answer : For RL loads, load current will not be in phase with load voltage and the diodes connected in antiparallel will allow the current to flow when the main thyristors are turned off. These diodes are called feedback diodes.