The output voltage waveform of a three-phase square-wave inverter contains

The output voltage waveform of a three-phase square-wave inverter contains 

(A) only even harmonics (B) both odd and even harmonic (C) only odd harmonics (D) only triple harmonics
by

2 Answers

Answer :

The output voltage waveform of a three-phase square-wave inverter contains only odd harmonics

by

Answer :

C
by

Related questions

A single-phase voltage source square -wave inverter feeds pure inductive load. The waveform of the load current will be

Description : A single-phase voltage source square -wave inverter feeds pure inductive load. The waveform of the load current will be

Last Answer : A single-phase voltage source square -wave inverter feeds pure inductive load. The waveform of the load current will be triangular

A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW

Description : A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is  (A) 119.05 A (B) 79.37 A (C) 68.73 A (D) 39.68 A

Last Answer : A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is 68.73 A

State the condition for RC differentiator. Draw the output waveform of RC integrator for square wave input.

Description : State the condition for RC differentiator. Draw the output waveform of RC integrator for square wave input.

Last Answer : Condition for RC differentiator: If the time duration T of the input waveform is comparable with the RC time constant (product of R and C) then the output waveform of the differentiator gets distorted. Hence for proper differentiator the condition is as follows: T >>RC

How should a tape recorder with good phase response reproduce a complex waveform, such as a square wave?

Description : How should a tape recorder with good phase response reproduce a complex waveform, such as a square wave?

Last Answer : With no distortion

An inverter converts

Description : An inverter converts  A) d.c. voltage to variable d.c. voltage B) ac. voltage to d.c. voltage C) d.c. voltage to ac. voltage of constant frequency D) d.c. voltage to ac. voltage of variable frequency 

Last Answer : An inverter converts d.c. voltage to a.c. voltage of variable frequency 

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave

Description : A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

Last Answer : A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is 1.0 A

A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the

Description : A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode.  (A) ... to one of the SCRs is missed, it will subsequently cause a high load current in the other SCR.

Last Answer : A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode. because the converter does not provide for free-wheeling for high values of triggering angles

a single phase full wave midpoint thyristor converter uses a 230/200V transformer with centre tap on the

Description : a single phase full wave midpoint thyristor converter uses a 230/200V transformer with centre tap on the secondary side. The P.I.V per thyristor is   (A) 100V (B)141.4V (C)200V (D)282.8V

Last Answer : d

A single phase CSI has capacitor C as the load. For a constant source current, the voltage across the capacitor

Description : A single phase CSI has capacitor C as the load. For a constant source current, the voltage across the capacitor is   (A) square wave (B) triangular wave (C) step function (D) pulsed wave

Last Answer : Step function

Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Description : Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Last Answer : Fig: Shunt capacitor filter along with full wave rectifier Fig: Waveform of full wave rectifier output and shunt capacitor filter output.

Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Description : Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Last Answer : 1. In positive half cycle (0 to Π): The end A of the secondary winding becomes positive and end B negative. This makes diode D1 and D4 forward biased while diode D2 and D3 are reverse biased. These two diodes will ... D2 and D3 when it is conducting is as follows.  B - D2 - RL - D3 - A 

Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

What type of circuit is on card 'A0AA2' at coordinate '29Q' shown in the illustration? EL-0099 A. Operational amplifier B. Digital logic inverter C. Square wave pulse generator D. Binary counter

Description : What type of circuit is on card 'A0AA2' at coordinate '29Q' shown in the illustration? EL-0099 A. Operational amplifier B. Digital logic inverter C. Square wave pulse generator D. Binary counter

Last Answer : Answer: A

A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately

Description : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the ... at half the rated speed is  (A) 0.354 (B) 0.372 (C) 0.90 (D) 0.955

Last Answer : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the losses, the power factor of the ac mains at half the rated speed is 0.354

A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load

Description : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component ... (B) 31% and 7.8 A (C) 66% and 6.8 A (D) 66% and 7.8 A

Last Answer : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component of input current will respectively be 31% and 7.8 A

_______ describes the position of the waveform relative to time 0. A) Frequency B) Phase C) Amplitude D) Voltage

Description : _______ describes the position of the waveform relative to time 0. A) Frequency B) Phase C) Amplitude D) Voltage

Last Answer : Phase

The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Description : The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Last Answer : (d) inverter

If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the top lead positive with repect to the lower lead B. direct current, half wave rectified with a ripple frequency of 60 hz C. direct current with the top lead negative with repect to the lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Last Answer : Answer: C

If a transformer primary is energised from a square wave voltage source, its output voltage will be (A) A square wave. (B) A sine wave. (C) A triangular wave. (D) A pulse wave.

Description : If a transformer primary is energised from a square wave voltage source, its output voltage will be (A) A square wave. (B) A sine wave. (C) A triangular wave. (D) A pulse wave.

Last Answer : (A) A square wave.

If a transformer primary is energised from a square wave voltage source, its output voltage will be a: ...

Description : If a transformer primary is energised from a square wave voltage source, its output voltage will be a:  (A) square wave (B) sine wave (C) triangular wave (D) pulse wave

Last Answer : D

In a 3-phase voltage source inverter used for speed control of induction motor, anti-parallel diodes are used

Description : In a 3-phase voltage source inverter used for speed control of induction motor, anti-parallel diodes are used across each switching device. The main purpose of diodes is to:

Last Answer : In a 3-phase voltage source inverter used for speed control of induction motor, anti-parallel diodes are used across each switching device. The main purpose of diodes is to: Allow the motor to return energy during regeneration

A 3-phase voltage source inverter is operated in 180 conduction mode. Which one of the following

Description : A 3-phase voltage source inverter is operated in 180o conduction mode. Which one of the following statements is true ?  (A) Both pole-voltage and line-voltage will have 3rd harmonic components ... from 3rd harmonic (D) Both pole-voltage and line-voltage will be free from 3rd harmonic components

Last Answer : A 3-phase voltage source inverter is operated in 180o conduction mode. Which one of the following statements is true ?  (A) Both pole-voltage and line-voltage will have 3rd harmonic components ... from 3rd harmonic (D) Both pole-voltage and line-voltage will be free from 3rd harmonic components

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Last Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

A freewheeling diode in a phase controlled converter

Description : A freewheeling diode in a phase controlled converter  A) Deceases the possibility of discontinuous conduction in the load B) Increases the possibility of discontinuous conduction in the load C) Reduces the power factor and causes over voltages D) Causes over voltages

Last Answer : A freewheeling diode in a phase controlled converter Deceases the possibility of discontinuous conduction in the load 

A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge

Description : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the dc current at 20 A ... thyristor will be reverse biased for a period of  (A) 125o (B) 120o (C) 60o (D) 55o

Last Answer : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the ... the solar cell resistance is 0.5 Ohm ,then each thyristor will be reverse biased for a period of 125o

A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and

Description : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high load inductance. The input ... 0.552 (C) IDF IPF = = 0.5; 0.478 (D) IDF IPF = = 0.5; 0.318 

Last Answer : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high ... (IDF) and the input power factor (IPF) of the converter will be IDF IPF = = 0.5; 0.478

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25 and an

Description : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is  (A) 0.78 (B) 0.827 (C) 0.866 (D) 0.9

Last Answer : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is 0.78

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc

Description : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt

Last Answer : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be 12.1 volt

In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is

Description : In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is   (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V 

Last Answer : a

Which of the following ECG characteristics is usually seen when a patient’s serum potassium level is low? a) U wave The U wave is an ECG waveform characteristic that may reflect Purkinje fiber repolarization. It is usually seen when a patient’s serum potassium level is low. b) T wave The T wave is an ECG characteristic reflecting repolarization of the ventricles. It may become tall or “peaked” if a patient’s serum potassium level is high. c) P wave The P wave is an ECG characteristic reflecting conduction of an electrical impulse through the atria. d) QT interval The QT interval is an ECG characteristic reflecting the time from ventricular depolarization to repolarization.

Description : Which of the following ECG characteristics is usually seen when a patient's serum potassium level is low? a) U wave The U wave is an ECG waveform characteristic that may ... interval The QT interval is an ECG characteristic reflecting the time from ventricular depolarization to repolarization.

Last Answer : a) U wave The U wave is an ECG waveform characteristic that may reflect Purkinje fiber repolarization. It is usually seen when a patient’s serum potassium level is low.

Which of the following circuits converts any arbitrary waveform into square waveform?

Description : Which of the following circuits converts any arbitrary waveform into square waveform? A) Hartley oscillator B) Schmitt trigger C) Differentiator D) RC phase shift oscillator 

Last Answer : Which of the following circuits converts any arbitrary waveform into square waveform? A) Hartley oscillator B) Schmitt trigger C) Differentiator D) RC phase shift oscillator 

Explain three phase bridge inverter.

Description : Explain three phase bridge inverter.

Last Answer : Three phase bridge inverter: Three phase bridge inverter converts DC voltage input to three-phase variable frequency variable voltage output. DC voltage source can be a DC source or output of the rectifier. ... in proper sequence. The switch may be thyristor or IGBT etc.

What type damper (with bias) clamps the most negative extremity of the output waveform to a negative potential?

Description : What type damper (with bias) clamps the most negative extremity of the output waveform to a negative potential?

Last Answer : Positive clamper with negative bias.

To which polarity does a positive damper with positive bins clamp the most negative extremity of the output waveform (positive or negative)?

Description : To which polarity does a positive damper with positive bins clamp the most negative extremity of the output waveform (positive or negative)?

Last Answer : Positive potential.

The output waveform produced due to time base generator in a CRO is a) saw tooth b) sinusoidal c) linear d) helical

Description : The output waveform produced due to time base generator in a CRO is a) saw tooth b) sinusoidal c) linear d) helical

Last Answer : a) saw tooth

Define filter. State its types. Draw any one filter with input and output waveform.

Description : Define filter. State its types. Draw any one filter with input and output waveform.

Last Answer : Defination : Filter is a circuit which remove or filtered out the AC component (ripple) Types of filter 1. Shunt Capacitor filter (C filter) 2. Series Inductor filter (L filter) 3. LC filter 4. filter (CLC filter) Shunt Capacitor filter (C filter) OR Waveforms:

Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform.

Description : Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform. 

Last Answer : Circuit diagram of bridge rectifier with π filter : Input and output waveform:

The output waveform of a 555 Timer is:

Description : The output waveform of a 555 Timer is: (1) Sinusoidal (2) Triangular (3) Rectangular (4) Elliptical 

Last Answer : The output waveform of a 555 Timer is: Rectangular

Explain the concept of lagging and leading phase angle by waveform.

Description : Explain the concept of lagging and leading phase angle by waveform.

Last Answer : i) Leading phase angle :  When two ac quantities of same frequency do not attain their respective zero or peak values simultaneously, then the quantities are said to be out-of-phase quantities. The ... Similarly, in the second diagram, the voltage is said to be lagging the current by  Φ.

Define the terms related to a.c. supply with waveform : i) Instantaneous value ii) Time period iii) Amplitude iv) Phase difference.

Description : Define the terms related to a.c. supply with waveform : i) Instantaneous value ii) Time period iii) Amplitude iv) Phase difference. 

Last Answer : i) Instantaneous value: The instantaneous value is the value of an alternating quantity (it may ac voltage or ac current or ac power) at a particular instant of time in the cycle .  OR  ... difference: Phase difference is the difference in phase angle between two sinusoids or phasors. 

Draw sinusoidal waveform of 3 phase emf and indicate the phase sequence.

Description : Draw sinusoidal waveform of 3 phase emf and indicate the phase sequence.

Last Answer : Phase sequence is R-Y-B.

Otp shows then disconnect's in zelio sine wave inverter luminous 1600va?

Description : Otp shows then disconnect's in zelio sine wave inverter luminous 1600va?

Last Answer : Need Answer

Should I Buy a Modified or Pure Sine Wave Inverter?

Description : Should I Buy a Modified or Pure Sine Wave Inverter?

Last Answer : Many people are unsure of the differences between a modified or pure sine wave inverter. Think of a modified sine wave inverter as a set of stairs. You will get power in blocks and there will be times ... to draw a lot of power should always be run on a sine wave inverter for consistency and safety.

Describe the operation of inductor with sinusoidal AC voltage as input. Draw waveform for voltage across and current through the inductor. Draw its phasor representation.

Description : Describe the operation of inductor with sinusoidal AC voltage as input. Draw waveform for voltage across and current through the inductor. Draw its phasor representation.

Last Answer : An alternating voltage is applied to a purely inductive coil, a back e.m.f. is produced due to self-inductance of the coil. The back e.m.f. at every step, opposes the rise of fall of current through the coil ... drop, the applied voltage has to overcome this self induced e.m.f. only.

Draw block diagram of Dual slope integrating voltmeter and also draw waveform for voltage V/s time.

Description : Draw block diagram of Dual slope integrating voltmeter and also draw waveform for voltage V/s time. 

Last Answer : Block diagram

For R-C series circuit draw (i) Circuit diagram (ii) Vector diagram (iii) Waveform of voltage and current

Description : For R-C series circuit draw (i) Circuit diagram (ii) Vector diagram (iii) Waveform of voltage and current

Last Answer : i) Circuit diagram ii)Vector diagram iii)Waveform of voltage and current

Explain lagging quantity and leading quantity, explain this concept with voltage and current waveform

Description : Explain lagging quantity and leading quantity, explain this concept with voltage and current waveform

Last Answer : When two alternating quantities attain their respective zero or peak values simultaneously, the quantities are said to be in-phase quantities. When the quantities do not attain their respective zero or ... current is leading the voltage or the voltage is said to be lagging behind the current.

Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of

Description : Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is   (A)sinusoidal (B) square (C) rectangular (D) triangular

Last Answer : Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is sinusoidal 

A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______

Description : A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______ A) DC voltage restorer B) Clamping circuit C) Both A and B D) None of these

Last Answer : A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______ A) DC voltage restorer B) Clamping circuit C) Both A and B D) None of these

The input voltage to an OP AMP is a large voltage step. The icetttput is an exponential waveform that...

Description : The input voltage to an OP AMP is a large voltage step. The output is an exponential waveform that changes to 0.25 V in 0.1µs (microsecond). The slew rate of the OP AMP is : -  a) 5V/µs b) 2.5 V/ µs c) 3V/µs d) 4.5V/ µs

Last Answer : The input voltage to an OP AMP is a large voltage step. The output is an exponential waveform that changes to 0.25 V in 0.1µs (microsecond). The slew rate of the OP AMP is : - 2.5 V/ µs