Process boilers with capacity of 2.5 MMBtu/h and above are also referred as _ a. Natural draft boilers b. Atmospheric boilers c. Both a. And b. d. None of the above

Process boilers with capacity of 2.5 MMBtu/h and above are also referred as _
a. Natural draft boilers
b. Atmospheric boilers
c. Both a. And b.
d. None of the above
by

1 Answer

Answer :

a. Natural draft boilers
by

Related questions

For process boilers , combustion air fans must meet the following requirements ___ a. The fan motor shall be driven by a variable speed drive b. The fan motor shall include controls that limit the fan motor demand to no more than 30 %. c. Both a. & b. d. None of the above

Description : For process boilers , combustion air fans must meet the following requirements ___ a. The fan motor shall be driven by a variable speed drive b. The fan motor shall include controls that limit the fan motor demand to no more than 30 %. c. Both a. & b. d. None of the above

Last Answer : c. Both a. & b.

Use of ______ is prohibited in process boilers. a. Use of a common gas b. combustion air control linkage c. jack shaft d. All of the above

Description : Use of ______ is prohibited in process boilers. a. Use of a common gas b. combustion air control linkage c. jack shaft d. All of the above

Last Answer : d. All of the above

Combustion air positive shut-off shall be provided on all newly installed _______ a. Grant boilers b. Process boilers c. Worcester boilers d. All of the above

Description : Combustion air positive shut-off shall be provided on all newly installed _______ a. Grant boilers b. Process boilers c. Worcester boilers d. All of the above

Last Answer : b. Process boilers

Boilers are used in places like 1. Domestic heating 2. Commercial heating 3. Industrial heating application 4. All of above

Description : Boilers are used in places like 1. Domestic heating 2. Commercial heating 3. Industrial heating application 4. All of above

Last Answer : 4. All of above

High pressure boilers operate at 1. Lower than 15 psig 2. Higher than 15 psig 3. 15 psig 4. None of above

Description : High pressure boilers operate at 1. Lower than 15 psig 2. Higher than 15 psig 3. 15 psig 4. None of above

Last Answer : 2. Higher than 15 psig

A safety valve usually employed with stationary boilers is (A) Lever safety valve (B) Dead weight safety valve (C) High steam and low water safety valve (D) All of these

Description : A safety valve usually employed with stationary boilers is (A) Lever safety valve (B) Dead weight safety valve (C) High steam and low water safety valve (D) All of these

Last Answer : (D) All of these

Industrial boilers are closed vessels that use a fuel source or electricity to generate ________for industrial purposes. • Fuel Food • Steam

Description : Industrial boilers are closed vessels that use a fuel source or electricity to generate ________for industrial purposes. • Fuel Food • Steam

Last Answer : • Steam

Steam Boilers is used in _________industries • Heating Requirement for Facility. • Steam for Batching. • Steam for Processing. • All of the above

Description : Steam Boilers is used in _________industries • Heating Requirement for Facility. • Steam for Batching. • Steam for Processing. • All of the above

Last Answer : • All of the above

Where are steam boilers used in the industries a) heating requirement for facility b) steam for batching c) steam for processing d) all of the above

Description : Where are steam boilers used in the industries a) heating requirement for facility b) steam for batching c) steam for processing d) all of the above

Last Answer : d) all of the above

The economiser is used in boilers to........ A]Increase thermal efficiency of boiler B]Economise on fuel C]Extract heat from the exhaust the gases D]Increase flue gas temperature

Description : The economiser is used in boilers to........ A]Increase thermal efficiency of boiler B]Economise on fuel C]Extract heat from the exhaust the gases D]Increase flue gas temperature

Last Answer : A]Increase thermal efficiency of boiler

The draught in locomotive boilers is produced by a ___________ a) Chimney b) Centrifugal fan c) Steam jet d) All of the above

Description : The draught in locomotive boilers is produced by a ___________ a) Chimney b) Centrifugal fan c) Steam jet d) All of the above

Last Answer : c) Steam jet

Water tube boilers produces steam at a________ pressure than that of fire tube boilers. a) Higher b) Lower c) Same d) None of the above

Description : Water tube boilers produces steam at a________ pressure than that of fire tube boilers. a) Higher b) Lower c) Same d) None of the above

Last Answer : a) Higher

Fire tube boilers are those in which a) Flue gases pass through tubes and water around it b) Water passes through the tubes and flue gases around it c) Work is done during adiabatic expansion d) Change is enthalpy

Description : Fire tube boilers are those in which a) Flue gases pass through tubes and water around it b) Water passes through the tubes and flue gases around it c) Work is done during adiabatic expansion d) Change is enthalpy

Last Answer : a) Flue gases pass through tubes and water around it

Water tube boilers are those in which a) Flue gases pass through tubes and water around it b) Water passes through the tubes and flue gases around it c) Work is done during adiabatic expansion d) Change is enthalpy

Description : Water tube boilers are those in which a) Flue gases pass through tubes and water around it b) Water passes through the tubes and flue gases around it c) Work is done during adiabatic expansion d) Change is enthalpy

Last Answer : b) Water passes through the tubes and flue gases around it

Process boiler is a type of boiler with a capacity of ____________Buts per hour a) 200,000 b) 300,000 c) 400,000 d) 50,000

Description : Process boiler is a type of boiler with a capacity of ____________Buts per hour a) 200,000 b) 300,000 c) 400,000 d) 50,000

Last Answer : b) 300,000

What is the main disadvantage of Lamont boiler ? a. Less flexible in design b. Low heat transfer rate c. Formation of bubbles d. Low steam generation capacity

Description : What is the main disadvantage of Lamont boiler ? a. Less flexible in design b. Low heat transfer rate c. Formation of bubbles d. Low steam generation capacity

Last Answer : c. Formation of bubbles

Type of Lamont boiler is_______ a. Forced circulation b. Natural circulation c. Over-through d. Positive forced circulation

Description : Type of Lamont boiler is_______ a. Forced circulation b. Natural circulation c. Over-through d. Positive forced circulation

Last Answer : a. Forced circulation

The generated heat is transferred to water to make ______ the process of boiling. • Steam • Boiler • Both • None

Description : The generated heat is transferred to water to make ______ the process of boiling. • Steam • Boiler • Both • None

Last Answer : • Steam

Hyperbolic cooling towers are also referred as a. Natural draft towers b. Cross flow towers c. Hyperboloid towers d. None of the above

Description : Hyperbolic cooling towers are also referred as a. Natural draft towers b. Cross flow towers c. Hyperboloid towers d. None of the above

Last Answer : Hyperboloid towers

Find the wrong statement. • Boiler is used to produce electricity in the energy business. • Boiler is used to produce steam for generating electricity. • Boiler can pressurize the water and can also evaporate it. All are wrong.

Description : Find the wrong statement. • Boiler is used to produce electricity in the energy business. • Boiler is used to produce steam for generating electricity. • Boiler can pressurize the water and can also evaporate it. All are wrong.

Last Answer : • Boiler can pressurize the water and can also evaporate it.

Adiabatic process is (A) Essentially an isentropic process is___________ (B) Non-heat transfer process (C) Reversible process (D) Constant temperature process

Description : Adiabatic process is (A) Essentially an isentropic process is___________ (B) Non-heat transfer process (C) Reversible process (D) Constant temperature process

Last Answer : (B) Non-heat transfer process

Direct relation between…….. &………of saturated steam, the amount of energy input to process easy to control. a) volume, pressure b) volume, temperature c) temperature, pressure d) None of above

Description : Direct relation between…….. &………of saturated steam, the amount of energy input to process easy to control. a) volume, pressure b) volume, temperature c) temperature, pressure d) None of above

Last Answer : c) temperature, pressure

On mollier chart ,free expansion or throttling process from High pressure to atmosphere is represented by • Horizontal straight line • Vertical straight line • Straight inclined line • Curved line

Description : On mollier chart ,free expansion or throttling process from High pressure to atmosphere is represented by • Horizontal straight line • Vertical straight line • Straight inclined line • Curved line

Last Answer : • Horizontal straight line

Which cooling Towers use a process similar to the one found in small evaporation active cooling units a) hyperbolic b) Tower c) condensate loop d) none of these

Description : Which cooling Towers use a process similar to the one found in small evaporation active cooling units a) hyperbolic b) Tower c) condensate loop d) none of these

Last Answer : a) hyperbolic

The heat in the boiler is used for making ______ a) steam b) condensing process c) ice d) none of these

Description : The heat in the boiler is used for making ______ a) steam b) condensing process c) ice d) none of these

Last Answer : a) steam

When gas changes to liquid through the process of condensation, the temperature A] Increases. B] Decreases C] Remains constant. D] None of the mentioned

Description : When gas changes to liquid through the process of condensation, the temperature A] Increases. B] Decreases C] Remains constant. D] None of the mentioned

Last Answer : C] Remains constant.

In a condensation process, _______ to _________ A] Gas, Solid B] Gas, Liquid C] Liquid, Gas D] Liquid, Solid

Description : In a condensation process, _______ to _________ A] Gas, Solid B] Gas, Liquid C] Liquid, Gas D] Liquid, Solid

Last Answer : B] Gas, Liquid

Based on the exhaust gas analysis, a controller maintains stoichiometric combustion __ a. by commanding a servo motor to adjust the combustion air damper b. By commanding servo motor to adjust the fuel supply valve. c. Both a. & b. d. None of the above.

Description : Based on the exhaust gas analysis, a controller maintains stoichiometric combustion __ a. by commanding a servo motor to adjust the combustion air damper b. By commanding servo motor to adjust the fuel supply valve. c. Both a. & b. d. None of the above.

Last Answer : c. Both a. & b.

Detecting and monitoring carbon monoxide assures the air/fuel ratio is not too rich as a. The excess air is trimmed b. Excess air is let out c. Both a. & b. d. None of above

Description : Detecting and monitoring carbon monoxide assures the air/fuel ratio is not too rich as a. The excess air is trimmed b. Excess air is let out c. Both a. & b. d. None of above

Last Answer : a. The excess air is trimmed

It is easy to detect and monitor excess air a. As oxygen not used for combustion is heated and discharged with the exhaust gases. b. Oxygen is discharged without heating c. Both a. & b. d. None of above

Description : It is easy to detect and monitor excess air a. As oxygen not used for combustion is heated and discharged with the exhaust gases. b. Oxygen is discharged without heating c. Both a. & b. d. None of above

Last Answer : a. As oxygen not used for combustion is heated and discharged with the exhaust gases.

A flue damper and a vent damper are two examples of _______ a. Combustion air positive shut off devices b. Combustion air negative shut off devices c. Both a. & b. d. None of the above

Description : A flue damper and a vent damper are two examples of _______ a. Combustion air positive shut off devices b. Combustion air negative shut off devices c. Both a. & b. d. None of the above

Last Answer : a. Combustion air positive shut off devices

If steam is pressurized _____ • It occupies more space • It occupies less space • Both are correct • None of the above

Description : If steam is pressurized _____ • It occupies more space • It occupies less space • Both are correct • None of the above

Last Answer : • It occupies less space

when steam is condensate volume is drastically……. a) reduces b) increase c) both a) & b) d) None of above

Description : when steam is condensate volume is drastically……. a) reduces b) increase c) both a) & b) d) None of above

Last Answer : a) reduces

If the water level inside the boiler were not carefully control cased… a) explosion b) overheat and fail c) both a) & b) d) None of above

Description : If the water level inside the boiler were not carefully control cased… a) explosion b) overheat and fail c) both a) & b) d) None of above

Last Answer : c) both a) & b)

The heat produced in this system is then rejected into the system as _______ a. Steam b. Boiler c. Both a & b d. None

Description : The heat produced in this system is then rejected into the system as _______ a. Steam b. Boiler c. Both a & b d. None

Last Answer : a. Steam

The temperature and pressure in saturated stem has__________relationship a) Direct b) indirect c) Neither of above d) both a and b

Description : The temperature and pressure in saturated stem has__________relationship a) Direct b) indirect c) Neither of above d) both a and b

Last Answer : b) indirect

Induced draft fans provided in large thermal power plant boilers have __________ blades. (A) Forward curved (B) Backward curved (C) Double curved (D) Radial or straight

Description : Induced draft fans provided in large thermal power plant boilers have __________ blades. (A) Forward curved (B) Backward curved (C) Double curved (D) Radial or straight

Last Answer : (B) Backward curved

Boiler water pH refers to a quantitative figure that expresses the acidity or alkalinity of boiler water. Ideally it should be between • 8.5 to 9.5 • 7.5 to 8.5 • 9.5 to 10.5

Description : Boiler water pH refers to a quantitative figure that expresses the acidity or alkalinity of boiler water. Ideally it should be between • 8.5 to 9.5 • 7.5 to 8.5 • 9.5 to 10.5

Last Answer : • 8.5 to 9.5

How many cooling towers are there near a reactor a) 1 b) 4 c) 5 d) 2

Description : How many cooling towers are there near a reactor a) 1 b) 4 c) 5 d) 2

Last Answer : b) 4

The most efficient cooling tower out of the following is (A) Induced draft (B) Forced draft (C) Natural draft (D) Atmospheric

Description : The most efficient cooling tower out of the following is (A) Induced draft (B) Forced draft (C) Natural draft (D) Atmospheric

Last Answer : (A) Induced draft

Where is water steam separator drum located in Lamont boiler ? a. Inside of the boiler b. Right above the furnace c. Before the feed water pump d. Outside the boiler

Description : Where is water steam separator drum located in Lamont boiler ? a. Inside of the boiler b. Right above the furnace c. Before the feed water pump d. Outside the boiler

Last Answer : d. Outside the boiler

What type of steam is generated by evaporator tube of Lamont boiler ? a. Saturated steam b. Unsaturated steam c. Superheated steam d. Flash steam

Description : What type of steam is generated by evaporator tube of Lamont boiler ? a. Saturated steam b. Unsaturated steam c. Superheated steam d. Flash steam

Last Answer : a. Saturated steam

In which year was Lamont boiler invented? a. 1905 b. 1910 c. 1920 d. 1925

Description : In which year was Lamont boiler invented? a. 1905 b. 1910 c. 1920 d. 1925

Last Answer : d. 1925

What is the pressure range between which Lamont boiler operator ? a. 80-120 bar b. 120-160 bar c. 180-360 bar d. 450-560 bar

Description : What is the pressure range between which Lamont boiler operator ? a. 80-120 bar b. 120-160 bar c. 180-360 bar d. 450-560 bar

Last Answer : b. 120-160 bar

Through which does the even circulation of water is possible in Lamont boiler ? a. Nozzles b. Water trough c. Feed pump d. Hose

Description : Through which does the even circulation of water is possible in Lamont boiler ? a. Nozzles b. Water trough c. Feed pump d. Hose

Last Answer : a. Nozzles

In what form are the boiler tube arrange in Lamont boiler ? a. Parallel in vertical b. Inclined vertically c. Parallel in horizontal d. Horizontally inclined

Description : In what form are the boiler tube arrange in Lamont boiler ? a. Parallel in vertical b. Inclined vertically c. Parallel in horizontal d. Horizontally inclined

Last Answer : c. Parallel in horizontal

Through what is feed water from hot-well is passed through, before entering steam and water drum in Lamont boiler? a. Evaporator tubes b. Economizer c. Distributor header d. Circulating pump

Description : Through what is feed water from hot-well is passed through, before entering steam and water drum in Lamont boiler? a. Evaporator tubes b. Economizer c. Distributor header d. Circulating pump

Last Answer : b. Economizer

What is called as the heart of the Lamont boiler? a. Water drum b. Centrifugal pump c. Furnace d. Blower

Description : What is called as the heart of the Lamont boiler? a. Water drum b. Centrifugal pump c. Furnace d. Blower

Last Answer : b. Centrifugal pump

Combustion of which fuels from following is source of heat for boiler 1. Wood 2. Coal 3. Oil 4. All of above

Description : Combustion of which fuels from following is source of heat for boiler 1. Wood 2. Coal 3. Oil 4. All of above

Last Answer : 4. All of above

Boiler works from application of which type of energies 1. Fuel combustion 2. Electricity 3. Nuclear energy 4. All of above

Description : Boiler works from application of which type of energies 1. Fuel combustion 2. Electricity 3. Nuclear energy 4. All of above

Last Answer : 4. All of above