It is easy to detect and monitor excess air a. As oxygen not used for combustion is heated and discharged with the exhaust gases. b. Oxygen is discharged without heating c. Both a. & b. d. None of above

It is easy to detect and monitor excess air
a. As oxygen not used for combustion is heated and discharged with the exhaust gases.
b. Oxygen is discharged without heating
c. Both a. & b.
d. None of above
by

1 Answer

Answer :

a. As oxygen not used for combustion is heated and discharged with the exhaust gases.
by

Related questions

Based on the exhaust gas analysis, a controller maintains stoichiometric combustion __ a. by commanding a servo motor to adjust the combustion air damper b. By commanding servo motor to adjust the fuel supply valve. c. Both a. & b. d. None of the above.

Description : Based on the exhaust gas analysis, a controller maintains stoichiometric combustion __ a. by commanding a servo motor to adjust the combustion air damper b. By commanding servo motor to adjust the fuel supply valve. c. Both a. & b. d. None of the above.

Last Answer : c. Both a. & b.

Green coal, in order to be burnt, must be (A) Heated sufficiently (B) Burnt in excess air (C) Heated to its ignition point (D) Burnt as powder

Description : Green coal, in order to be burnt, must be (A) Heated sufficiently (B) Burnt in excess air (C) Heated to its ignition point (D) Burnt as powder

Last Answer : (C) Heated to its ignition point

The economiser is used in boilers to........ A]Increase thermal efficiency of boiler B]Economise on fuel C]Extract heat from the exhaust the gases D]Increase flue gas temperature

Description : The economiser is used in boilers to........ A]Increase thermal efficiency of boiler B]Economise on fuel C]Extract heat from the exhaust the gases D]Increase flue gas temperature

Last Answer : A]Increase thermal efficiency of boiler

A __________ is a type of heat exchange system where water is heated to its' boiling point via combustion of a fuel blown through a tube submerged in water. a. Condensate loop b. Hyperbolic cooling tower c. Steam boiler d. All of above

Description : A __________ is a type of heat exchange system where water is heated to its' boiling point via combustion of a fuel blown through a tube submerged in water. a. Condensate loop b. Hyperbolic cooling tower c. Steam boiler d. All of above

Last Answer : c. Steam boiler

Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Description : Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Last Answer : (D) It erodes furnace walls

Combustion is the ideal air/fuel ratio where a. the mixing proportion is correct, b. the fuel is completely burned c. the oxygen is entirely consumed d. All of the above

Description : Combustion is the ideal air/fuel ratio where a. the mixing proportion is correct, b. the fuel is completely burned c. the oxygen is entirely consumed d. All of the above

Last Answer : d. All of the above

Oxygen trim control strategy __ a. continuously measures the oxygen content in the flue gas b. adjusts the combustion air flow c. Continually tuning the air-fuel mixture. d. All of above

Description : Oxygen trim control strategy __ a. continuously measures the oxygen content in the flue gas b. adjusts the combustion air flow c. Continually tuning the air-fuel mixture. d. All of above

Last Answer : d. All of above

For process boilers , combustion air fans must meet the following requirements ___ a. The fan motor shall be driven by a variable speed drive b. The fan motor shall include controls that limit the fan motor demand to no more than 30 %. c. Both a. & b. d. None of the above

Description : For process boilers , combustion air fans must meet the following requirements ___ a. The fan motor shall be driven by a variable speed drive b. The fan motor shall include controls that limit the fan motor demand to no more than 30 %. c. Both a. & b. d. None of the above

Last Answer : c. Both a. & b.

A flue damper and a vent damper are two examples of _______ a. Combustion air positive shut off devices b. Combustion air negative shut off devices c. Both a. & b. d. None of the above

Description : A flue damper and a vent damper are two examples of _______ a. Combustion air positive shut off devices b. Combustion air negative shut off devices c. Both a. & b. d. None of the above

Last Answer : a. Combustion air positive shut off devices

Detecting and monitoring carbon monoxide assures the air/fuel ratio is not too rich as a. The excess air is trimmed b. Excess air is let out c. Both a. & b. d. None of above

Description : Detecting and monitoring carbon monoxide assures the air/fuel ratio is not too rich as a. The excess air is trimmed b. Excess air is let out c. Both a. & b. d. None of above

Last Answer : a. The excess air is trimmed

Use of ______ is prohibited in process boilers. a. Use of a common gas b. combustion air control linkage c. jack shaft d. All of the above

Description : Use of ______ is prohibited in process boilers. a. Use of a common gas b. combustion air control linkage c. jack shaft d. All of the above

Last Answer : d. All of the above

Combustion air positive shut-off shall be provided on all newly installed _______ a. Grant boilers b. Process boilers c. Worcester boilers d. All of the above

Description : Combustion air positive shut-off shall be provided on all newly installed _______ a. Grant boilers b. Process boilers c. Worcester boilers d. All of the above

Last Answer : b. Process boilers

Which of these is an output of a ‘Furnace’? a. Fuel gas b. Cool Air c. Flue gases d. Water Vapor

Description : Which of these is an output of a ‘Furnace’? a. Fuel gas b. Cool Air c. Flue gases d. Water Vapor

Last Answer : c. Flue gases

What is the function of boiler? • To burn the fuel in a confined closed system With the supply of air • To generate steam in varying pressure • To generate steam at constant pressure • To produce flue gases by burning fuel at a given pressure

Description : What is the function of boiler? • To burn the fuel in a confined closed system With the supply of air • To generate steam in varying pressure • To generate steam at constant pressure • To produce flue gases by burning fuel at a given pressure

Last Answer : • To generate steam at constant pressure

Direct relation between…….. &………of saturated steam, the amount of energy input to process easy to control. a) volume, pressure b) volume, temperature c) temperature, pressure d) None of above

Description : Direct relation between…….. &………of saturated steam, the amount of energy input to process easy to control. a) volume, pressure b) volume, temperature c) temperature, pressure d) None of above

Last Answer : c) temperature, pressure

Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Description : Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following option is incorrect about the sludges? a) Sludges are soft, loose and slimy precipitate b) They are non-adherent deposits and can be easily removed c) Formed generally at heated portions of the boiler d) Can be removed by blow down operation

Description : Which of the following option is incorrect about the sludges? a) Sludges are soft, loose and slimy precipitate b) They are non-adherent deposits and can be easily removed c) Formed generally at heated portions of the boiler d) Can be removed by blow down operation

Last Answer : c) Formed generally at heated portions of the boiler

Combustion of which fuels from following is source of heat for boiler 1. Wood 2. Coal 3. Oil 4. All of above

Description : Combustion of which fuels from following is source of heat for boiler 1. Wood 2. Coal 3. Oil 4. All of above

Last Answer : 4. All of above

Boiler works from application of which type of energies 1. Fuel combustion 2. Electricity 3. Nuclear energy 4. All of above

Description : Boiler works from application of which type of energies 1. Fuel combustion 2. Electricity 3. Nuclear energy 4. All of above

Last Answer : 4. All of above

Boiler is a enclosed vessel that provides a) Expansion b) Ignition c) Combustion d) None of the above

Description : Boiler is a enclosed vessel that provides a) Expansion b) Ignition c) Combustion d) None of the above

Last Answer : c) Combustion

Presence of moisture in fuel oil would (A) Keep the burner tips cool (B) Aid in proper combustion (C) Because sputtering, possibly extinguishing flame (D) Clean the nozzles

Description : Presence of moisture in fuel oil would (A) Keep the burner tips cool (B) Aid in proper combustion (C) Because sputtering, possibly extinguishing flame (D) Clean the nozzles

Last Answer : (D) Clean the nozzles

Which of the following is the combustion accessory of a boiler? • Fuel oil system • Gas system • Coal system • All of the above

Description : Which of the following is the combustion accessory of a boiler? • Fuel oil system • Gas system • Coal system • All of the above

Last Answer : • All of the above

Basic Parts of a Boiler. Burner, • the combustion chamber, • the heat exchanger • All of the above

Description : Basic Parts of a Boiler. Burner, • the combustion chamber, • the heat exchanger • All of the above

Last Answer : • All of the above

A boiler is an enclosed vessel that provides a means for ________ and ______ heat to water until it becomes hot water or steam. a. Generate, boiler b. Condenser, loop c. Combustion, transfers d. All of above

Description : A boiler is an enclosed vessel that provides a means for ________ and ______ heat to water until it becomes hot water or steam. a. Generate, boiler b. Condenser, loop c. Combustion, transfers d. All of above

Last Answer : c. Combustion, transfers

Which of the following is not a result of the excess of impurity in boiler-feed. a) Scale and sludge formation b) Decomposition c) Corrosion, priming and foaming d) Caustic embrittlement

Description : Which of the following is not a result of the excess of impurity in boiler-feed. a) Scale and sludge formation b) Decomposition c) Corrosion, priming and foaming d) Caustic embrittlement

Last Answer : b) Decomposition

Boilers are used in places like 1. Domestic heating 2. Commercial heating 3. Industrial heating application 4. All of above

Description : Boilers are used in places like 1. Domestic heating 2. Commercial heating 3. Industrial heating application 4. All of above

Last Answer : 4. All of above

The propulsion of water into steam drum by extremely rapid, almost explosive boiling of water at the heating surface is called ___________ a) Foaming b) Priming c) Corrosion d) Caustic embrittlement

Description : The propulsion of water into steam drum by extremely rapid, almost explosive boiling of water at the heating surface is called ___________ a) Foaming b) Priming c) Corrosion d) Caustic embrittlement

Last Answer : b) Priming

The relative heat absorption for successively added equal areas of boiler convection heating surfaces__________ (A) Increases (B) Decreases (C) Remain unaffected (D) First increases and then decreases

Description : The relative heat absorption for successively added equal areas of boiler convection heating surfaces__________ (A) Increases (B) Decreases (C) Remain unaffected (D) First increases and then decreases

Last Answer : (B) Decreases

Steam Boilers is used in _________industries • Heating Requirement for Facility. • Steam for Batching. • Steam for Processing. • All of the above

Description : Steam Boilers is used in _________industries • Heating Requirement for Facility. • Steam for Batching. • Steam for Processing. • All of the above

Last Answer : • All of the above

Steam produced in a boiler can be used for a variety of purposes including space heating, drying and _________________ a. Sterilization b. Humidification c. Power generation d. All of above

Description : Steam produced in a boiler can be used for a variety of purposes including space heating, drying and _________________ a. Sterilization b. Humidification c. Power generation d. All of above

Last Answer : d. All of above

Where are steam boilers used in the industries a) heating requirement for facility b) steam for batching c) steam for processing d) all of the above

Description : Where are steam boilers used in the industries a) heating requirement for facility b) steam for batching c) steam for processing d) all of the above

Last Answer : d) all of the above

The biggest loss in the boiler is a) Moisture in fuel b) Dry flue gases c) Steam formation d) Unburnt carbon

Description : The biggest loss in the boiler is a) Moisture in fuel b) Dry flue gases c) Steam formation d) Unburnt carbon

Last Answer : b) Dry flue gases

Fire tube boilers are those in which a) Flue gases pass through tubes and water around it b) Water passes through the tubes and flue gases around it c) Work is done during adiabatic expansion d) Change is enthalpy

Description : Fire tube boilers are those in which a) Flue gases pass through tubes and water around it b) Water passes through the tubes and flue gases around it c) Work is done during adiabatic expansion d) Change is enthalpy

Last Answer : a) Flue gases pass through tubes and water around it

Water tube boilers are those in which a) Flue gases pass through tubes and water around it b) Water passes through the tubes and flue gases around it c) Work is done during adiabatic expansion d) Change is enthalpy

Description : Water tube boilers are those in which a) Flue gases pass through tubes and water around it b) Water passes through the tubes and flue gases around it c) Work is done during adiabatic expansion d) Change is enthalpy

Last Answer : b) Water passes through the tubes and flue gases around it

Scavenging air in diesel engine means a. air used for combustion under pressure b. forced air for cooling the cylinder c. burnt air containing products of combustion d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

Description : Scavenging air in diesel engine means a. air used for combustion under pressure b. forced air for cooling the cylinder c. burnt air containing products of combustion d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

Last Answer : ANSWER d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

when steam is condensate volume is drastically……. a) reduces b) increase c) both a) & b) d) None of above

Description : when steam is condensate volume is drastically……. a) reduces b) increase c) both a) & b) d) None of above

Last Answer : a) reduces

If the water level inside the boiler were not carefully control cased… a) explosion b) overheat and fail c) both a) & b) d) None of above

Description : If the water level inside the boiler were not carefully control cased… a) explosion b) overheat and fail c) both a) & b) d) None of above

Last Answer : c) both a) & b)

The heat produced in this system is then rejected into the system as _______ a. Steam b. Boiler c. Both a & b d. None

Description : The heat produced in this system is then rejected into the system as _______ a. Steam b. Boiler c. Both a & b d. None

Last Answer : a. Steam

In general, the limit of inflammability/explosion limit of fuel gases is widened by the (A) Increase in gas pressure (B) Increase in temperature (i.e. preheating) (C) Use of pure oxygen for combustion instead of air (D) All (A), (B) & (C)

Description : In general, the limit of inflammability/explosion limit of fuel gases is widened by the (A) Increase in gas pressure (B) Increase in temperature (i.e. preheating) (C) Use of pure oxygen for combustion instead of air (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

'Flare tower' used in industry is meant for (A) Venting off (after burning) the excess inflammable/toxic gases at high pressure (B) Absorbing the pollutant gases from the furnace exhaust (C) Cooling of furnace exhaust gases (D) None of these

Description : 'Flare tower' used in industry is meant for (A) Venting off (after burning) the excess inflammable/toxic gases at high pressure (B) Absorbing the pollutant gases from the furnace exhaust (C) Cooling of furnace exhaust gases (D) None of these

Last Answer : (A) Venting off (after burning) the excess inflammable/toxic gases at high pressure

The product of efficiency & heat transferred to the working fluid is? a. Net temperature change b. Net work done c. Net enthalpy change d. None of the mentioned

Description : The product of efficiency & heat transferred to the working fluid is? a. Net temperature change b. Net work done c. Net enthalpy change d. None of the mentioned

Last Answer : b. Net work done

Means for giving direction to the circulation of gases in furnaces are (A) Fans (B) Arrangement of heating stock in the furnaces (C) Location of outlet ports and heating & combustion devices (D) All (A), (B) and (C)

Description : Means for giving direction to the circulation of gases in furnaces are (A) Fans (B) Arrangement of heating stock in the furnaces (C) Location of outlet ports and heating & combustion devices (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In a steam condenser, the partial pressure of steam and air are 0.06 bar and 0.007 bar respectively. The condenser pressure is (A) 0.007 bar (B) 0.053 bar (C) 0.06 bar (D) 0.067 bar

Description : In a steam condenser, the partial pressure of steam and air are 0.06 bar and 0.007 bar respectively. The condenser pressure is (A) 0.007 bar (B) 0.053 bar (C) 0.06 bar (D) 0.067 bar

Last Answer : (D) 0.067 bar

What is the reason to service a cooling tower? a) to ensure proper air flow b) to clean the tubes c) to inspect the water pump d) all of these

Description : What is the reason to service a cooling tower? a) to ensure proper air flow b) to clean the tubes c) to inspect the water pump d) all of these

Last Answer : all of these

What happens when air dissolves in condensate? a) non corrosive b) temperature of air increases c) corrosive d) none of above

Description : What happens when air dissolves in condensate? a) non corrosive b) temperature of air increases c) corrosive d) none of above

Last Answer : c) corrosive

Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Description : Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Last Answer : (B) Keeping the flue gas exhaust temperature very high

Stack heat losses can be minimised by (A) Controlling the excess air (B) Oxygen enrichment of combustion air (C) Using low c.v. fuels (D) Maintaining proper draft in the furnace

Description : Stack heat losses can be minimised by (A) Controlling the excess air (B) Oxygen enrichment of combustion air (C) Using low c.v. fuels (D) Maintaining proper draft in the furnace

Last Answer : (A) Controlling the excess air

Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to volatile matter percentage in coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Description : Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to ... coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Last Answer : (D) Calorific value of natural gas is more than that of LPG

A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has been used for combustion (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Description : A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has ... (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Last Answer : (C) Complete combustion of fuel has taken place

Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Description : Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Last Answer : (C) 20