Description : Name the method which is not a sowing method a) Broadcasting b) Hill dropping c) Dibbling d) Hitching
Last Answer : <!-- [endif] -->Hitching
Description : One of the most common tasks on the farm is A. Hitching C. Both A & B B. Non hitching. D. None A & B
Last Answer : Both A & B
Description : There are a few accessories necessary for plough are . a) Jointer b) Coulter c) Land wheel d) All of above
Last Answer : All of above
Description : It is that part of the plough bottom which penetrates into the soil and makes a horizontal cut below the surface. a. Land side c. body d. None of the above
Last Answer : Ans – b. Share
Description : Sowing behind the plough can be done by a device known as ……… b. Seed tube c. Plough tube d. None of the above
Last Answer : Ans - a. malobansa
Description : In gravity canals, F.S.L. is a. Always at the ground level b. Always below the ground level c. Generally 4 to 5 meters above the ground level d. Only a few cm above the ground level
Last Answer : d. Only a few cm above the ground level
Description : How do I go about hitching one car to another?
Last Answer : answer:If one of the cars has a trailer hitch, you should be able to put the drive wheels of the 2nd car on a mini-trailer and haul it that way. A new trailer hitch trailer rental is probably going to be cheaper than driving the 2nd car...
Description : The unit of length in S.I. units is (a) meter (b) centimeter (c) kilometer (d) millimeter.
Last Answer : Answer : a
Description : Minimum horsepower of pump required for filling 50m3 water tank, 20 metres high from ground in 30 minutes by lifting water from a well 5 metres below the ground level is a.5.45 KW b.7.5 KW c.6.81 KW d.Tapered bearing e.66.8 KW
Last Answer : c. 6.81 KW
Description : A round viewing window with a 20 centimeter diameter is installed in a tank at the Shedd Aquarium. It is 5 meters below the water surface. The force on the window is approximately: w) 1,500 Newtons x) 10,000 Newtons y) 25,000 Newtons z) 50,000 Newtons
Last Answer : ANSWER: W -- 1,500 NEWTONS
Description : arthwork in embankment for railway with manual compaction should be done in layers not exceeding-------------- a) 15 centimeter b) 20 centimeters c) 25 centimeters d) 30 centimeters*
Last Answer : d) 30 centimeters*
Description : It is a machine used for placing the seeds in a continuous stream in furrows at uniform rate and at controlled depth with an arrangement of covering the seeds with soil. a. Seed tube b. Seed dropper d. None of the above.
Last Answer : Ans - c. Seed drill
Description : It is the process of placing seeds in holes made in the seedbed and closing the seed with soil. In this method, seeds are placed in holes made at definite depth at fixed spacing. b. Drilling c. Broadcasting d. None of the above.
Last Answer : Ans - a. Dibbing
Description : is a machine for placing the seeds in a continuous flow. a) Seed drill b) Transplanting c) Hill dropping d) Check row planting
Last Answer : Seed drill
Description : is the process of placing seeds in holes made in seedbed and covering them. a) Broadcasting. b) Dibbling c) Drilling. d) Transplanting
Last Answer : Dibbling
Description : Paddy cono weeder is useful for. a) Weeding between rows of crops like cotton for sugarcane. b) For uprooting and burying weeds in between standing rows of rice crops in in wetland. c) For weeding in raw crops in rain fed. d) For placing seed in continuous flow.
Last Answer : For uprooting and burying weeds in between standing rows of rice crops in in wetland.
Description : machine is used for placing the seeds in continuous furrows at uniform rate. a) Dry land weeder b) Junior home c) Seed drill d) Engine operated weeder
Description : An old parchment describes the location of buried treasure: 'On the island there are only two trees, A and B, and the remains of a gallows. Start at the gallows and count the steps required to walk ... when he gets to the island finds the gallows missing. Is there any way he can still get -Riddles
Last Answer : A simple experiment with a ruler and paper shows that any position for the gallows leads to the same point.
Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (A) Direct shear stress
Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (C) Tensile stress
Description : During turning the traction while operating MB plough a) Plough should be lifted b) Plough should not be lifted c) Stop the tractor and lift the plough d) Unable to lift Ans. a
Last Answer : ans a
Description : In comparison to MB plough, the draft is less in disc plough because a) It roll over the soil instead of sliding b) It has lower contact area c) It has larger cutting edge d) None of these Ans. a
Description : The function of landside in mb plough is to a) Resist the side draft force b) Increase pulverization c) Decrease draft d) All of these Ans. a
Description : Working width of disc plough can be increased by a) Disc angle b) Gang angle c) Vertical suction d) Horizontal clearance Ans. a
Description : The adjustment in MB plough for increasing the depth of operation a) Vertical suction b) Horizontal suction c) Gang angle d) Disc angle Ans. a
Description : A furrow cross-section in a country plough is commonly a) Circular b) Triangular c) Rectangular d) Trapezoidal
Last Answer : ans b
Description : The two primary tillage equipments are 1. MB and disc harrow 2. Disc plough and disc harrow 3. Disc harrow and cultivator 4. MB and subsoiler
Last Answer : ans 4
Description : Dead furrow is made by 1. One way MB plough 2. 2 way MB plough 3. ridger 4. disc harrow
Last Answer : ans 1
Description : Vertical section of plough influences 1. Pulverization 2. Depth of cut 3. Width of cut 4. direction of pull
Last Answer : ans 2
Description : Power tillers operate most satisfactory with? 1. Rotary tillage 2. Plough 3. Transport carts 4. reapers
Description : Which of the following is not a tractor drawn primary tillage tool? 1. Disc plough 2. rotavator 3. Country plough 4. Bar harrow
Last Answer : ans 3
Description : Which one of the following is not a secondary tillage tool? 1. Disc Plough 2. Disc harrow 3. Mould Board 4. none of these
Description : Which of the following is not a tractor drawn tillage tool? 1. Cultivator 2. Augar plough 3. Harrow 4. Plank
Description : Ridger is also known as riding plough and moulds board plough. a. Single c. Half d. None of the above. Ans - b. Double
Last Answer : Ans - b. Double
Description : This type of plough penetrate deeper than the conventional cultivation machinery and break up the layers of the soil. a. Chisel plough b. Disc plough d. None of the above
Last Answer : Ans - c. sub-soiler plough
Description : It Is used for deep tillage and penetration of soil for storage for rain water in crop root zone. b. Disc plough c. Mould board plough d. None of the above
Last Answer : Ans- a. Chisel plough
Description : plough leaves the soil in rough and more cloddy conditions. b. Mould board c. Both a And b d. None of the above
Last Answer : <!-- [if !supportLists] -->a. <!-- [endif] -->Ans - a. Disc
Description : Disc angle in a standard disc plough varies from a. 25-35 ° c. 45-55 ° d. 55-65 °
Last Answer : Ans - b. 42-45 °
Description : Which one of the following is an accessory to mould board plough? a. Share b. mould board c. frog
Last Answer : <!-- [endif] --> Ans- d. jointer
Description : This type mould boars plough is used for sticky soil. b. Sod or breaker c. Stubble d. None of the above
Last Answer : Ans –a. Slat type
Description : This type mould boards plough is used for tough soil of grasses. a. slat c. Stubble d. None of the above
Last Answer : Ans- b. Sod or breaker
Description : Mould board, disc, Chisel and Sub soil plough are the tillage equipments. b. Secondary c. post d. None of the above
Last Answer : Ans - a. Primary
Description : In method, row to row and plant to plant distance is uniform. a) Seed dropping behind the plough b) Transplanting c) Hill dropping d) Check row planting
Last Answer : Check row planting
Description : In method, seeds are dropped at fixed spacing and not in a continuous stream. a) Seed dropping behind the plough b) Transplanting c) Hill dropping d) Check row planting
Last Answer : Hill dropping
Description : consists of preparing seedlings in nursery and then planting these seedlings in the prepared field. a) Seed dropping behind the plough b) Transplanting c) Hill dropping d) Check row planting
Last Answer : Transplanting
Description : is very common method used in villages. a) Seed dropping behind the plough b) Transplanting c) Hill dropping
Last Answer : Seed dropping behind the plough
Description : is a method of ploughing in which the soil broken and turn along the contours. a. Normal ploughing c. Contour ploughing b. Sub soil plough. d. Disc plough
Last Answer : Contour ploughing
Description : Standard disc Plough consists of steel disc of _ diameter a) 20 to 40 cm. c) 60 to 90 cm b) 30 to 60 cm. d) 70 to 100 cm
Last Answer : 60 to 90 cm
Description : is not component of M.B. Plough a) Share. c) Land side b) Shoe. d) Tail piece
Last Answer : Shoe.
Description : Select the function of Moldboard plough. a) Lifting the soil. c) Pulverizing the soil b) Cutting the furrow slice d) All of the above
Last Answer : All of the above