How Does A Condensing Unit Work?

How Does A Condensing Unit Work?
by

1 Answer

Answer :

Inside the condenser, the refrigerant vapor is compressed and forced through a heat exchange coil, condensing it into a liquid and rejecting the heat previously absorbed from the cool indoor area. The condenser's heat exchanger is generally cooled by a fan blowing outside air through it.
by

Related questions

The effect that takes place which results in cooling action is1. Condensing 2. Heating 3. Cooling 4. Evaporating

Description : The effect that takes place which results in cooling action is1. Condensing 2. Heating 3. Cooling 4. Evaporating

Last Answer : Evaporating

How does a Ventless Condensing Drying System work?

Description : How does a Ventless Condensing Drying System work?

Last Answer : Individual condensing dryers use air-to-air condensers to remove the moisture from the air before sending it back though the drum. Hot, moist air exiting the drum is passed over a set of metal ... temperature increase in the laundry room is approximately one degree Fahrenheit for a ten by ten room.)

Do condensing boilers increase efficency?

Description : Do condensing boilers increase efficency?

Last Answer : Condensing boilers do work very well and are quite efficient. They will take several years to recoup their price, however. If it is only for savings, you should consider the length of time involved.

Pick up the incorrect statement (a) lithium bromide used in vapour absorption cycle is nonvolatile (b) lithium bromide plant can't operate below 0°C (c) a separator is used in lithium bromide plant to remove the unwanted water vapour by condensing (d) concentration of solution coming out of lithium bromide generator is more in comparison to that entering the generator

Description : Pick up the incorrect statement (a) lithium bromide used in vapour absorption cycle is nonvolatile (b) lithium bromide plant can't operate below 0°C (c) a separator is used in lithium ... of solution coming out of lithium bromide generator is more in comparison to that entering the generator

Last Answer : Ans: c

A certain refrigerating system has a normal operating suction pressure of 10 kg/cm gauge and condensing pressure ofabout 67 kg/cm. The refrigerant used is (a) Ammonia (b) Carbon dioxide (c) Freon (d) Brine

Description : A certain refrigerating system has a normal operating suction pressure of 10 kg/cm gauge and condensing pressure ofabout 67 kg/cm. The refrigerant used is (a) Ammonia (b) Carbon dioxide (c) Freon (d) Brine

Last Answer : Ans: b

Condensing temperature in a refrigerator is the temperature (a) of cooling medium (b) of freezing zone (c) of evaporator (d) at which refrigerant gas becomes liquid

Description : Condensing temperature in a refrigerator is the temperature (a) of cooling medium (b) of freezing zone (c) of evaporator (d) at which refrigerant gas becomes liquid

Last Answer : Ans: d

The condensing pressure due to the presence of non-condensable gases, as compared to that actually required forcondensing temperatures without non-condensable gases, (a) will be higher (b) will be lower (c) will remain unaffected (d) may be higher or lower depending upon the nature of non-condensable gases

Description : The condensing pressure due to the presence of non-condensable gases, as compared to that actually required forcondensing temperatures without non-condensable gases, (a) will be higher (b) will be ... remain unaffected (d) may be higher or lower depending upon the nature of non-condensable gases

Last Answer : Ans: a

The temperature at which the air cannot hold all the water vapour mixed in it and some vapour starts condensing is called as A. humidification temperature B. dehumidification temperature C. dew point temperature D. none of the above

Description : The temperature at which the air cannot hold all the water vapour mixed in it and some vapour starts condensing is called as A. humidification temperature B. dehumidification temperature C. dew point temperature D. none of the above

Last Answer : ANSWER : C

What is the temperature at which the water vapour in the mixture of water vapour in air, starts condensing called? A. condensation temperature B. dew point temperature C. vaporization temperature D. all of the above

Description : What is the temperature at which the water vapour in the mixture of water vapour in air, starts condensing called? A. condensation temperature B. dew point temperature C. vaporization temperature D. all of the above

Last Answer : ANSWER : B

The main purpose of an electric space heater installed in a large AC generator is to _____________. A. keep the lube oil warm for quick starting B. prevent moisture from condensing in the windings when the machine is shutdown C. prevent the windings from becoming brittle D. prevent acidic pitting of the slip rings

Description : The main purpose of an electric space heater installed in a large AC generator is to _____________. A. keep the lube oil warm for quick starting B. prevent moisture from condensing in the ... is shutdown C. prevent the windings from becoming brittle D. prevent acidic pitting of the slip rings

Last Answer : Answer: B

The main purpose of an electric space heater installed in a large AC generator is to _____________. A. prevent the windings from becoming brittle B. prevent moisture from condensing in the windings during shutdown C. prevent acidic pitting of the slip rings D. keep the lube oil warm for quick starting

Description : The main purpose of an electric space heater installed in a large AC generator is to _____________. A. prevent the windings from becoming brittle B. prevent moisture from condensing in the windings during ... C. prevent acidic pitting of the slip rings D. keep the lube oil warm for quick starting

Last Answer : Answer: B

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

If air (a non-condensing gas) is present in a condensing vapor stream, it will __________ the condensation rate of vapor. (A) Increase (B) Decrease (C) Not affect (D) Increase the condensing film co-efficient as well as

Description : If air (a non-condensing gas) is present in a condensing vapor stream, it will __________ the condensation rate of vapor. (A) Increase (B) Decrease (C) Not affect (D) Increase the condensing film co-efficient as well as

Last Answer : (B) Decrease

This in-between phase of stellar nurseries and star formation in stellar evolution is when the gathered dust is still condensing to form a star. A. Alpha Stage B. Stellar Genesis C. Protostar (Answer) D. Star of Adam

Description : This in-between phase of stellar nurseries and star formation in stellar evolution is when the gathered dust is still condensing to form a star. A. Alpha Stage B. Stellar Genesis C. Protostar (Answer) D. Star of Adam

Last Answer : C. Protostar (Answer)

Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for counter flow and parallel flow can be theoretically same when any one of the fluids (hot or cold fluid) passes through the heat exchanger at constant temperature (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs (D) Phase change in case of a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Description : Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for ... a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Last Answer : (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs

Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both the cases. The recommended arrangement is (A) Finned tube heat exchanger with air inside and steam outside (B) Finned tube heat exchanger with air outside and steam inside (C) Shell and tube heat exchanger with air inside tubes and steam on shell side (D) Shell and tube heat exchanger with air on shell side and steam inside tubes

Description : Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both ... steam on shell side (D) Shell and tube heat exchanger with air on shell side and steam inside tubes

Last Answer : (B) Finned tube heat exchanger with air outside and steam inside

Presence of a non-condensing gas in a condensing vapour (A) Increases the rate of condensation (B) Decreases thermal resistance (C) Is desirable to increase the film co-efficient (D) None of these

Description : Presence of a non-condensing gas in a condensing vapour (A) Increases the rate of condensation (B) Decreases thermal resistance (C) Is desirable to increase the film co-efficient (D) None of these

Last Answer : (D) None of these

In a gas-liquid shell and tube heat exchanger, the(A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure gases are corrosive in nature (C) Gases to be heated/cooled is normally routed through the shell side, because the corrosion caused by the cooling water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Description : In a gas-liquid shell and tube heat exchanger, the (A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure ... water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

LMTD for counter-flow and parallel flow heat exchanger will be the same, when the (A) Cold fluid is heated to a certain temperature by condensing steam (isothermal fluid) (B) Outlet temperature of both the hot and cold fluid are same (C) Outlet temperature of hot fluid is less than the outlet temperature of the cold fluid (D) None of these

Description : LMTD for counter-flow and parallel flow heat exchanger will be the same, when the (A) Cold fluid is heated to a certain temperature by condensing steam (isothermal fluid) (B) Outlet temperature of ... temperature of hot fluid is less than the outlet temperature of the cold fluid (D) None of these

Last Answer : (A) Cold fluid is heated to a certain temperature by condensing steam (isothermal fluid)

In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation will (A) Increase (B) Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Description : In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation ... Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Last Answer : (C) Remain unchanged

The film co-efficient is decreased due to the presence of non-condensing gases in the vapors. The film co-efficient of superheated vapor as compared to that of saturated vapor is (A) More (B) Less (C) Some (D) Either more or less; depends on the nature of vapor

Description : The film co-efficient is decreased due to the presence of non-condensing gases in the vapors. The film co-efficient of superheated vapor as compared to that of saturated vapor is (A) More (B) Less (C) Some (D) Either more or less; depends on the nature of vapor

Last Answer : (C) Some

LMTD for evaporators & condensers for a given terminal parameters & set of conditions for counter-flow is equal to that for parallel flow. In such heat exchangers, with one of the fluids condensing or evaporating, the surface area required is the least in the __________ flow. (A) Parallel (B) Mixed (C) Counter flow (D) Same in either 'a', b' or 'c'

Description : LMTD for evaporators & condensers for a given terminal parameters & set of conditions for counter-flow is equal to that for parallel flow. In such heat exchangers, with one of the fluids condensing or evaporating, the surface ... Parallel (B) Mixed (C) Counter flow (D) Same in either 'a', b' or 'c'

Last Answer : (D) Same in either 'a', b' or 'c'

The film co-efficient between condensing vapour and metal wall increases with (A) Increasing temperature of the vapour (B) Decreasing temperature of the vapour (C) Increasing viscosity of the film of condensate (D) Increasing temperature drop

Description : The film co-efficient between condensing vapour and metal wall increases with (A) Increasing temperature of the vapour (B) Decreasing temperature of the vapour (C) Increasing viscosity of the film of condensate (D) Increasing temperature drop

Last Answer : (A) Increasing temperature of the vapour

condensing output data to exhibit specific information is a. calculating b. recording c. merging d. summarizing

Description : condensing output data to exhibit specific information is a. calculating b. recording c. merging d. summarizing

Last Answer : recording

Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film wise condensation (C) If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Description : Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film ... place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Last Answer : (B) Suitable coating or vapour additive is used to promote film wise condensation

The heat in the boiler is used for making ______ a) steam b) condensing process c) ice d) none of these

Description : The heat in the boiler is used for making ______ a) steam b) condensing process c) ice d) none of these

Last Answer : a) steam

condensing output data to exhibit specific information is a. calculating b. recording c. merging d. summarizing

Description : condensing output data to exhibit specific information is a. calculating b. recording c. merging d. summarizing

Last Answer : d. summarizing

The MAIN purpose of burnishing is: A. To help eliminating excess mercury (condensing) B. To condense margins C. Polishing of filling

Description : The MAIN purpose of burnishing is: A. To help eliminating excess mercury (condensing) B. To condense margins C. Polishing of filling

Last Answer : B. To condense margins

condensing output data to exhibit specific information is a. calculating b. recording c. merging d. summarizing

Description : condensing output data to exhibit specific information is a. calculating b. recording c. merging d. summarizing

Last Answer : d. summarizing

What types of proteins are involved in the packaging and condensing of DNA into tightly wound nucleosome structures of a chromosome?

Description : What types of proteins are involved in the packaging and condensing of DNA into tightly wound nucleosome structures of a chromosome?

Last Answer : Histone

Increase the output of work per unit time c) Automatic tool. c) manual tool d) Implement tool. d) matching tool

Description : Increase the output of work per unit time c) Automatic tool. c) manual tool d) Implement tool. d) matching tool

Last Answer : manual tool

Objectives of Tillage a. To destroy the prevent weeds. c) both A & B b. To reduce soil and erosion d) increase the output of work per unit time

Description : Objectives of Tillage a. To destroy the prevent weeds. c) both A & B b. To reduce soil and erosion d) increase the output of work per unit time

Last Answer : both A & B

What is defined as the force per unit area?  A. Pressure  B. Energy  C. Work  D. Power

Description : What is defined as the force per unit area?  A. Pressure  B. Energy  C. Work  D. Power

Last Answer : Pressure