Pick up the incorrect statement (a) lithium bromide used in vapour absorption cycle is nonvolatile (b) lithium bromide plant can't operate below 0°C (c) a separator is used in lithium bromide plant to remove the unwanted water vapour by condensing (d) concentration of solution coming out of lithium bromide generator is more in comparison to that entering the generator

Pick up the incorrect statement (a) lithium bromide used in vapour absorption cycle is nonvolatile (b) lithium bromide plant can't operate below 0°C (c) a separator is used in lithium bromide plant to remove the unwanted water vapour by condensing (d) concentration of solution coming out of lithium bromide generator is more in comparison to that entering the generator
by

1 Answer

Answer :

Ans: c
by
selected by

Related questions

The evolution of heat of solution takes place in ammonia absorption plant when (a) ammonia vapour goes into solution (b) ammonia vapour is driven out of solution (c) lithium bromide mixes with ammonia (d) weak solution mixes with strong solution

Description : The evolution of heat of solution takes place in ammonia absorption plant when (a) ammonia vapour goes into solution (b) ammonia vapour is driven out of solution (c) lithium bromide mixes with ammonia (d) weak solution mixes with strong solution

Last Answer : Ans: a

Pick up the correct statement about giving up of heat from one medium to other in ammonia absorption system (a) strong solution to weak solution (b) weak solution to strong solution (c) strong solution to ammonia vapour (d) ammonia vapour to strong solution.

Description : Pick up the correct statement about giving up of heat from one medium to other in ammonia absorption system (a) strong solution to weak solution (b) weak solution to strong solution (c) strong solution to ammonia vapour (d) ammonia vapour to strong solution.

Last Answer : Ans: b

The COP of a vapour compression plant in comparison to vapour absorption plant is (a) more (b) less (c) same (d) more/less depending on size of plant

Description : The COP of a vapour compression plant in comparison to vapour absorption plant is (a) more (b) less (c) same (d) more/less depending on size of plant

Last Answer : Ans: a

In vapour compression cycle the condition off refrigerant is dry saturated vapour (a) after passing through the condenser (b) before passing through the condenser (c)before entering the expansion valve (d) before entering the compressor

Description : In vapour compression cycle the condition off refrigerant is dry saturated vapour (a) after passing through the condenser (b) before passing through the condenser (c)before entering the expansion valve (d) before entering the compressor

Last Answer : Ans: D

In vapour compression cycle, the condition of refrigerant is high pressure saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is high pressure saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Last Answer : Ans: d

In vapour compression cycle, the condition of refrigerant is very wet vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is very wet vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Last Answer : Ans: c

In vapour compression cycle, the condition of refrigerant is saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion throttle valve (d) before entering the expansion valve

Last Answer : Ans: a

Cooling water is required for following equipment in ammonia absorption plant (a) condenser (b) evaporator (c) condenser and absorber (d) condenser, absorber and separator (rectifier).

Description : Cooling water is required for following equipment in ammonia absorption plant (a) condenser (b) evaporator (c) condenser and absorber (d) condenser, absorber and separator (rectifier).

Last Answer : Ans: d

The temperature at which the air cannot hold all the water vapour mixed in it and some vapour starts condensing is called as A. humidification temperature B. dehumidification temperature C. dew point temperature D. none of the above

Description : The temperature at which the air cannot hold all the water vapour mixed in it and some vapour starts condensing is called as A. humidification temperature B. dehumidification temperature C. dew point temperature D. none of the above

Last Answer : ANSWER : C

What is the temperature at which the water vapour in the mixture of water vapour in air, starts condensing called? A. condensation temperature B. dew point temperature C. vaporization temperature D. all of the above

Description : What is the temperature at which the water vapour in the mixture of water vapour in air, starts condensing called? A. condensation temperature B. dew point temperature C. vaporization temperature D. all of the above

Last Answer : ANSWER : B

A standard ice point temperature corresponds to the temperature of (a) water at 0°C (b) ice at - 4°C (c) mixture of ice, water and vapour under equilibrium conditions under NTP conditions (d) mixture of ice and water Under equilibrium conditions.

Description : A standard ice point temperature corresponds to the temperature of (a) water at 0°C (b) ice at - 4°C (c) mixture of ice, water and vapour under equilibrium conditions under NTP conditions (d) mixture of ice and water Under equilibrium conditions.

Last Answer : Ans: D

Most of the domestic refrigerators work on the following refrigeration system (a) vapour compression (b) vapour absorption (c) carnot cycle (d) electrolux refrigerator

Description : Most of the domestic refrigerators work on the following refrigeration system (a) vapour compression (b) vapour absorption (c) carnot cycle (d) electrolux refrigerator

Last Answer : Ans: a

Ammonia-absorption refrigeration cycle requires (a) very little work input (b) maximum work input (c) nearly same work input as for vapour compression cycle (d) zero work input

Description : Ammonia-absorption refrigeration cycle requires (a) very little work input (b) maximum work input (c) nearly same work input as for vapour compression cycle (d) zero work input

Last Answer : Ans: a

The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Description : The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Last Answer : Ans: d

Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film wise condensation (C) If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Description : Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film ... place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Last Answer : (B) Suitable coating or vapour additive is used to promote film wise condensation

Choose the wrong statement (a) Temperature of medium being cooled must be below that of the evaporator (b) Refrigerant leaves the condenser as liquid (c) All solar thermally operated absorption systems are capable only of intermittent operation (d) frost on evaporator reduces heat transfer

Description : Choose the wrong statement (a) Temperature of medium being cooled must be below that of the evaporator (b) Refrigerant leaves the condenser as liquid (c) All solar thermally operated absorption systems are capable only of intermittent operation (d) frost on evaporator reduces heat transfer

Last Answer : Ans: a

The value of COP in vapour compression cycle is usually (a) always less than unity (b) always more than unity (c) equal to unity (d) any one of the above

Description : The value of COP in vapour compression cycle is usually (a) always less than unity (b) always more than unity (c) equal to unity (d) any one of the above

Last Answer : Ans: b

A certain refrigerating system has a normal operating suction pressure of 10 kg/cm gauge and condensing pressure ofabout 67 kg/cm. The refrigerant used is (a) Ammonia (b) Carbon dioxide (c) Freon (d) Brine

Description : A certain refrigerating system has a normal operating suction pressure of 10 kg/cm gauge and condensing pressure ofabout 67 kg/cm. The refrigerant used is (a) Ammonia (b) Carbon dioxide (c) Freon (d) Brine

Last Answer : Ans: b

Condensing temperature in a refrigerator is the temperature (a) of cooling medium (b) of freezing zone (c) of evaporator (d) at which refrigerant gas becomes liquid

Description : Condensing temperature in a refrigerator is the temperature (a) of cooling medium (b) of freezing zone (c) of evaporator (d) at which refrigerant gas becomes liquid

Last Answer : Ans: d

The condensing pressure due to the presence of non-condensable gases, as compared to that actually required forcondensing temperatures without non-condensable gases, (a) will be higher (b) will be lower (c) will remain unaffected (d) may be higher or lower depending upon the nature of non-condensable gases

Description : The condensing pressure due to the presence of non-condensable gases, as compared to that actually required forcondensing temperatures without non-condensable gases, (a) will be higher (b) will be ... remain unaffected (d) may be higher or lower depending upon the nature of non-condensable gases

Last Answer : Ans: a

The dew point is the: a. Dry bulb temperature on a psychrometer b. Temperature at which water vapour will start to be absorbed into the air c. Temperature below which water vapour will start to condense out of the air d. Pressure below which water vapour will start to condense out of the air e. Temperature at which water will start to evaporate

Description : The dew point is the: a. Dry bulb temperature on a psychrometer b. Temperature at which water vapour will start to be absorbed into the air c. Temperature below which water vapour will start to ... vapour will start to condense out of the air e. Temperature at which water will start to evaporate

Last Answer : Answer: C

Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Description : Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Last Answer : Ans: d

In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Description : In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Last Answer : Ans: c

The lower horizontal line of the refrigeration cycle plotted on pressure-enthalpy-diagram represents (a) condensation of the refrigerant vapour (b) evaporation of the refrigerant liquid (c) compression of the refrigerant vapour (d) metering of the refrigerant liquid

Description : The lower horizontal line of the refrigeration cycle plotted on pressure-enthalpy-diagram represents (a) condensation of the refrigerant vapour (b) evaporation of the refrigerant liquid (c) compression of the refrigerant vapour (d) metering of the refrigerant liquid

Last Answer : Ans: b

Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Description : Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Last Answer : Ans: b

The higher temperature in vapour compression cycle occurs at (a) compressor discharge. (b) expansion valve (c) evaporator (d) condenser discharge

Description : The higher temperature in vapour compression cycle occurs at (a) compressor discharge. (b) expansion valve (c) evaporator (d) condenser discharge

Last Answer : Ans: a

In a vapour compression cycle, the refrigerant immediately after expansion valve is (a) liquid (b) sub-cooled liquid (c) saturated liquid (d) wet vapour

Description : In a vapour compression cycle, the refrigerant immediately after expansion valve is (a) liquid (b) sub-cooled liquid (c) saturated liquid (d) wet vapour

Last Answer : Ans: d

Domestic refrigerator working on vapour compression cycle uses the following type of expansion device (a) electrically operated throttling valve (b) manually operated valve (c) thermostatic valve (d) capillary tube

Description : Domestic refrigerator working on vapour compression cycle uses the following type of expansion device (a) electrically operated throttling valve (b) manually operated valve (c) thermostatic valve (d) capillary tube

Last Answer : Ans: d

The vapour compression refrigerator employs the following cycle (a) Rankine (b) Carnot (c) Reversed Carnot. (d) Brayton

Description : The vapour compression refrigerator employs the following cycle (a) Rankine (b) Carnot (c) Reversed Carnot. (d) Brayton

Last Answer : Ans: c

In vapour compression cycle the condition of refrigerant is superheated vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) beforeentering the expansion valve

Description : In vapour compression cycle the condition of refrigerant is superheated vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) beforeentering the expansion valve

Last Answer : Ans: b

Vapour compression refrigeration is some what like (a) Carnot cycle (b) Rankine cycle (c) reversedCamot cycle (d) reversed Rankine cycle

Description : Vapour compression refrigeration is some what like (a) Carnot cycle (b) Rankine cycle (c) reversedCamot cycle (d) reversed Rankine cycle

Last Answer : Ans: C

Most high speed compression ignition engine operate on A. dual cycle B. otto cycle C. diesel cycle D.Carnot cycle

Description : Most high speed compression ignition engine operate on A. dual cycle B. otto cycle C. diesel cycle D.Carnot cycle

Last Answer : ANSWER : A

Most high-speed compression engines operate on a. diesel cycle b. Otto cycle c. dual cycle d. Carnot cycle

Description : Most high-speed compression engines operate on a. diesel cycle b. Otto cycle c. dual cycle d. Carnot cycle

Last Answer : ANSWER c. dual cycle

Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in the tubes of natural circulation evaporators is in the range of 0.3 to 0.9 metre/second (C) Duhring's plot is used for calculating the concentration of solution (D) In a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Description : Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in ... a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Last Answer : (C) Duhring's plot is used for calculating the concentration of solution

One ton of the refrigeration is (a) the standard unit used in refrigeration problems (b) the cooling effect produced by melting 1 ton of ice (c) the refrigeration effect to freeze 1 ton of water at 0°C into ice at 0°C in 24 hours (d) the refrigeration effect to produce 1 ton of ice at NTP conditions

Description : One ton of the refrigeration is (a) the standard unit used in refrigeration problems (b) the cooling effect produced by melting 1 ton of ice (c) the refrigeration effect to freeze 1 ton of water at ... ice at 0°C in 24 hours (d) the refrigeration effect to produce 1 ton of ice at NTP conditions

Last Answer : Ans: c

Pick up the incorrect statement from the following: (A) The pH value of water indicates the logarithm of reciprocal of hydrogen ion concentration in water (B) Higher value of pH means lower hydrogen ion concentration (C) Lower value of pH means higher hydrogen ion contraction (D) Lower value of pH gives alkaline solution

Description : Pick up the incorrect statement from the following:  (A) The pH value of water indicates the logarithm of reciprocal of hydrogen ion concentration in  water  (B) Higher value of pH ... value of pH means higher hydrogen ion contraction  (D) Lower value of pH gives alkaline solution 

Last Answer : (D) Lower value of pH gives alkaline solution 

Pick up the incorrect statement from the following: (A) The water entering the slow sand filters should be treated by 9.386 coagulants (B) The depth of water on the filter should be twice the depth of the filter sand (C) When the filter head is 0.75 times the depth of filter sand, the water obtained is purest (D) All the above

Description : Pick up the incorrect statement from the following:  (A) The water entering the slow sand filters should be treated by 9.386 coagulants  (B) The depth of water on the filter should be twice the ... is 0.75 times the depth of filter sand, the water obtained is purest  (D) All the above 

Last Answer : (D) All the above 

Pick up the incorrect statement from the following for allowing workers to enter sewers A. The particular manhole and one manhole on upstream and one manhole on downstream should remain open for 30 minutes B. Proper tests for the presence of poisonous gases must be carried out C. The men entering the manhole should be advised to smoke in the sewer D. Warning signals should be erected

Description : Pick up the incorrect statement from the following for allowing workers to enter sewers A. The particular manhole and one manhole on upstream and one manhole on downstream should remain open for 30 ... entering the manhole should be advised to smoke in the sewer D. Warning signals should be erected

Last Answer : ANS: C

When, H1 = Total heat of air entering the coil (heating or cooling) H2 = Total heat of air leaving the coil (heating or cooling) H3 = Total heat of air at the end of the process (humidification or dehumidification) then, the sensible heat factor (H2 – H1) / (H3 – H1) represents the process of A. cooling and humidification B. cooling and dehumidification C. heating and humidification D. heating and dehumidification

Description : When, H1 = Total heat of air entering the coil (heating or cooling) H2 = Total heat of air leaving the coil (heating or cooling) H3 = Total heat of air at the end of ... A. cooling and humidification B. cooling and dehumidification C. heating and humidification D. heating and dehumidification

Last Answer : ANSWER : C

The _____________ sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : The _____________ sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: d Explanation: The air inlet temperature sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength whereas the engine temperature sensor senses the ... gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.

For spark ignition engine, the equivalence ratio of mixture entering the combustion chamber has values (A) for idling and for peak power conditions (B) for both idling and peak power conditions (C) for idling and for peak power conditions (D) for both idling and peak power conditions

Description : For spark ignition engine, the equivalence ratio of mixture entering the combustion chamber has values (A) for idling and for peak power conditions (B) for both idling and peak power conditions (C) for idling and for peak power conditions (D) for both idling and peak power conditions

Last Answer : ANSWER (B) for both idling and peak power conditions

The C.O.P. of a domestic refrigerator in comparison to domestic air conditioner will be (a) same (b) more (c) less (d) dependent on weather conditions

Description : The C.O.P. of a domestic refrigerator in comparison to domestic air conditioner will be (a) same (b) more (c) less (d) dependent on weather conditions

Last Answer : Ans: c

In a refrigeration system, heat absorbed in comparison to heat rejected is (a) more (b) less (c) less for small capacity and more for high capacity. (d) more for small capacity and less for high capacity

Description : In a refrigeration system, heat absorbed in comparison to heat rejected is (a) more (b) less (c) less for small capacity and more for high capacity. (d) more for small capacity and less for high capacity

Last Answer : Ans: b

The size of inlet valve of an engine in comparison to exhaust valve is A. more B. less C. same D. varies from design to design

Description : The size of inlet valve of an engine in comparison to exhaust valve is A. more B. less C. same D. varies from design to design

Last Answer : ANSWER : B

Highest temperature encountered in refrigeration cycle should be (a) near critical temperature of refrigerant (b) above critical temperature (c) atcritica. temperature (d) much below critical temperature

Description : Highest temperature encountered in refrigeration cycle should be (a) near critical temperature of refrigerant (b) above critical temperature (c) atcritica. temperature (d) much below critical temperature

Last Answer : Ans: d

The suction pipe diameter of refrigerating unit compressor in comparison to delivery side is (a) bigger (b) smaller (c) equal (d) smaller/bigger depending on capacity

Description : The suction pipe diameter of refrigerating unit compressor in comparison to delivery side is (a) bigger (b) smaller (c) equal (d) smaller/bigger depending on capacity

Last Answer : Ans: a

Mass flow ratio of NH3 in comparison to Freon-12 for same refrigeration load and same temperature limits is of the orderof (a) 1 : 1 (b) 1 : 9 (c) 9 : 1 (d) 1 : 3

Description : Mass flow ratio of NH3 in comparison to Freon-12 for same refrigeration load and same temperature limits is of the orderof (a) 1 : 1 (b) 1 : 9 (c) 9 : 1 (d) 1 : 3

Last Answer : Ans: b

If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Description : If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Last Answer : Ans :c

Which is the incorrect statement about Carnot cycle?  A. It is used as the alternate standard of comparison of all heat engines.  B. All the heat engines are based on Carnot cycle.  C. It provides concept of maximising work output between the two temperature limits.  D. all of the above

Description : Which is the incorrect statement about Carnot cycle?  A. It is used as the alternate standard of comparison of all heat engines.  B. All the heat engines are based on Carnot cycle.  C. It provides concept of maximising work output between the two temperature limits.  D. all of the above

Last Answer : Answer: B

The ratio of partial pressure of water vapour in a mixture to the saturation pressure of water at the same temperature of the mixture is called as A. humidity B. partial humidity C. specific humidity D. relative humidity

Description : The ratio of partial pressure of water vapour in a mixture to the saturation pressure of water at the same temperature of the mixture is called as A. humidity B. partial humidity C. specific humidity D. relative humidity

Last Answer : ANSWER : D