If air (a non-condensing gas) is present in a condensing vapor stream, it will __________ the condensation rate of vapor. (A) Increase (B) Decrease (C) Not affect (D) Increase the condensing film co-efficient as well as

If air (a non-condensing gas) is present in a condensing vapor stream, it

will __________ the condensation rate of vapor.

(A) Increase

(B) Decrease

(C) Not affect

(D) Increase the condensing film co-efficient as well as


by

1 Answer

Answer :

(B) Decrease

by

Related questions

Presence of a non-condensing gas in a condensing vapour (A) Increases the rate of condensation (B) Decreases thermal resistance (C) Is desirable to increase the film co-efficient (D) None of these

Description : Presence of a non-condensing gas in a condensing vapour (A) Increases the rate of condensation (B) Decreases thermal resistance (C) Is desirable to increase the film co-efficient (D) None of these

Last Answer : (D) None of these

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

The film co-efficient is decreased due to the presence of non-condensing gases in the vapors. The film co-efficient of superheated vapor as compared to that of saturated vapor is (A) More (B) Less (C) Some (D) Either more or less; depends on the nature of vapor

Description : The film co-efficient is decreased due to the presence of non-condensing gases in the vapors. The film co-efficient of superheated vapor as compared to that of saturated vapor is (A) More (B) Less (C) Some (D) Either more or less; depends on the nature of vapor

Last Answer : (C) Some

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation will (A) Increase (B) Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Description : In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation ... Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Last Answer : (C) Remain unchanged

Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film wise condensation (C) If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Description : Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film ... place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Last Answer : (B) Suitable coating or vapour additive is used to promote film wise condensation

Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for counter flow and parallel flow can be theoretically same when any one of the fluids (hot or cold fluid) passes through the heat exchanger at constant temperature (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs (D) Phase change in case of a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Description : Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for ... a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Last Answer : (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs

The film co-efficient between condensing vapour and metal wall increases with (A) Increasing temperature of the vapour (B) Decreasing temperature of the vapour (C) Increasing viscosity of the film of condensate (D) Increasing temperature drop

Description : The film co-efficient between condensing vapour and metal wall increases with (A) Increasing temperature of the vapour (B) Decreasing temperature of the vapour (C) Increasing viscosity of the film of condensate (D) Increasing temperature drop

Last Answer : (A) Increasing temperature of the vapour

The heat transfer co-efficient in film type condensation is __________ that for dropwise condensation. (A) Greater than (B) Lower than (C) Is same as (D) Half

Description : The heat transfer co-efficient in film type condensation is __________ that for dropwise condensation. (A) Greater than (B) Lower than (C) Is same as (D) Half

Last Answer : (B) Lower than

The rough value of diffusion co-efficient of water vapor into air at 25°C may be about __________ cm2 /sec. (A) 0.25 (B) 2.5 (C) 1.25 (D) 0.0025

Description : The rough value of diffusion co-efficient of water vapor into air at 25°C may be about __________ cm2 /sec. (A) 0.25 (B) 2.5 (C) 1.25 (D) 0.0025

Last Answer : (A) 0.25

In a gas-liquid shell and tube heat exchanger, the(A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure gases are corrosive in nature (C) Gases to be heated/cooled is normally routed through the shell side, because the corrosion caused by the cooling water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Description : In a gas-liquid shell and tube heat exchanger, the (A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure ... water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

What is the temperature at which the water vapour in the mixture of water vapour in air, starts condensing called? A. condensation temperature B. dew point temperature C. vaporization temperature D. all of the above

Description : What is the temperature at which the water vapour in the mixture of water vapour in air, starts condensing called? A. condensation temperature B. dew point temperature C. vaporization temperature D. all of the above

Last Answer : ANSWER : B

In case of a vertical tube evaporator, with increase in the liquor level, the __________ is increased. (A) Velocity of circulation (B) Liquor-film co-efficient (C) Both (A) and (B) (D) Neither (A) and (B)

Description : In case of a vertical tube evaporator, with increase in the liquor level, the __________ is increased. (A) Velocity of circulation (B) Liquor-film co-efficient (C) Both (A) and (B) (D) Neither (A) and (B)

Last Answer : (D) Neither (A) and (B)

Addition of filter aid to the slurry before filtration is done to __________ of the cake. (A) Increase the porosity (B) Increase the compressibility co-efficient (C) Decrease the porosity (D) Decrease the compressibility co-efficient

Description : Addition of filter aid to the slurry before filtration is done to __________ of the cake. (A) Increase the porosity (B) Increase the compressibility co-efficient (C) Decrease the porosity (D) Decrease the compressibility co-efficient

Last Answer : (A) Increase the porosity

The Reynolds number of the liquid was increased 100 fold for a laminar falling film used for gas-liquid contacting. Assuming penetrating theory is applicable, the fold increase in the mass transfer co-efficient (Kc ) for the same system is(A) 100(B) 10(C) 5(D) 1.

Description : The Reynolds number of the liquid was increased 100 fold for a laminar falling film used for gas-liquid contacting. Assuming penetrating theory is applicable, the fold increase in the mass transfer co-efficient (Kc ) for the same system is. (A) 100 (B) 10 (C) 5 (D) 1

Last Answer : (B) 10

In a vapor-liquid contacting equipment, the overall gas phase mass transfer co-efficient (M.T.C), KG is related to individual co-efficients (KG and KL ) as (A) KG = 1/KG + m/KL (B) 1/KG = 1/KG + m/KL (C) 1/KG = 1/KL + m/KG (D) KG = 1/KL + m/KG

Description : In a vapor-liquid contacting equipment, the overall gas phase mass transfer co-efficient (M.T.C), KG is related to individual co-efficients (KG and KL ) as (A) KG = 1/KG + m/KL (B) 1/KG = 1/KG + m/KL (C) 1/KG = 1/KL + m/KG (D) KG = 1/KL + m/KG

Last Answer : (B) 1/KG = 1/KG + m/KL

The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient(B) Increasing the liquid film co-efficient(C) Increasing the total pressure(D) Decreasing the total pressure

Description : The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient (B) Increasing the liquid film co-efficient (C) Increasing the total pressure (D) Decreasing the total pressure

Last Answer : (A) Increasing the gas film co-efficient

The film thickness for laminar film condensation on vertical surface __________ from top to bottom. (A) Cumulatively increases (B) Cumulatively decreases (C) Remain constant (D) And the surface conductance increase

Description : The film thickness for laminar film condensation on vertical surface __________ from top to bottom. (A) Cumulatively increases (B) Cumulatively decreases (C) Remain constant (D) And the surface conductance increase

Last Answer : (A) Cumulatively increases

Removal of __________ heat is involved in the condensation of a vapor under saturated conditions. (A) Super (B) Sensible (C) Latent (D) Both (B) & (C)

Description : Removal of __________ heat is involved in the condensation of a vapor under saturated conditions. (A) Super (B) Sensible (C) Latent (D) Both (B) & (C)

Last Answer : (B) Sensible

Increasing the liquor level in the evaporator results in the (A) Decreased capacity (B) Increase in liquor film co-efficient (C) Decreased effect of hydrostatic head (D) Increased true temperature drop

Description : Increasing the liquor level in the evaporator results in the (A) Decreased capacity (B) Increase in liquor film co-efficient (C) Decreased effect of hydrostatic head (D) Increased true temperature drop

Last Answer : (A) Decreased capacity

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

. A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of all the effects is -less than that in a single effect evaporator system (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect (C) Boiling point elevation in a single effect system is much higher than that in any effect in a multi-effect system (D) Heat transfer co-efficient in a single effect is much lower than that in any effect in a multi-effect system

Description : . A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of ... in a single effect is much lower than that in any effect in a multi-effect system

Last Answer : (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect

A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co-efficient and fi° is the fugacity of the pure component i. the Ki value (Yi = Ki xi) is therefore, in general a function of (A) Temperature only (B) Temperature and pressure only (C) Temperature, pressure and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Description : A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co- ... and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Last Answer : (C) Temperature, pressure and liquid composition xi only

Mass transfer co-efficient is directly proportional to DAB 0.5 , according to __________ theory. (A) Penetration (B) Surface renewal (C) Film (D) None of these

Description : Mass transfer co-efficient is directly proportional to DAB 0.5 , according to __________ theory. (A) Penetration (B) Surface renewal (C) Film (D) None of these

Last Answer : (A) Penetration

Mass transfer co-efficient is directly proportional to DAB according to the __________ theory. (A) Film (B) Penetration (C) Surface-renewal (D) None of these

Description : Mass transfer co-efficient is directly proportional to DAB according to the __________ theory. (A) Film (B) Penetration (C) Surface-renewal (D) None of these

Last Answer : (A) Film

Calculation of mass transfer co-efficient is mostly/normally done using __________ theory. (A) Surface renewal (B) Film (C) Penetration (D) None of these

Description : Calculation of mass transfer co-efficient is mostly/normally done using __________ theory. (A) Surface renewal (B) Film (C) Penetration (D) None of these

Last Answer : (B) Film

Controlling heat transfer film co-efficient is the one, which offers __________ resistance to heat transfer. (A) No (B) The least (C) The largest (D) Lower

Description : Controlling heat transfer film co-efficient is the one, which offers __________ resistance to heat transfer. (A) No (B) The least (C) The largest (D) Lower

Last Answer : (C) The largest

Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Description : Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Last Answer : Option A

Pick out the wrong statement. (A) In solvent extraction, the distribution co-efficient should be as large as possible for solvent economy (B) With increase in pressure, the solubility of gases in solvent increases at a fixed temperature (C) Decrease in Murphree plate efficiency is an indication of entrainment in distillation column (D) The capacity of a distillation column is maximum at total reflux

Description : Pick out the wrong statement. (A) In solvent extraction, the distribution co-efficient should be as large as possible for solvent economy (B) With increase in pressure, the solubility of ... in distillation column (D) The capacity of a distillation column is maximum at total reflux

Last Answer : (D) The capacity of a distillation column is maximum at total reflux

As the difference between the wall temperature and bulk temperature increases, the boiling heat transfer co-efficient (A) Continues to increase (B) Continues to decrease (C) Goes through a minimum (D) Goes through a maximum

Description : As the difference between the wall temperature and bulk temperature increases, the boiling heat transfer co-efficient (A) Continues to increase (B) Continues to decrease (C) Goes through a minimum (D) Goes through a maximum

Last Answer : (C) Goes through a minimum

Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Description : Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Last Answer : (C) Increase the shell side heat transfer co-efficient

In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Description : In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Last Answer : (B) Decreases

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

Recycling back of outlet stream to the reactor from an ideal CSTR carrying out a first order liquid phase reaction will result in __________ in conversion. (A) Decrease (B) Increase (C) No change (D) Either (A) or (B), depends on the type of reaction

Description : Recycling back of outlet stream to the reactor from an ideal CSTR carrying out a first order liquid phase reaction will result in __________ in conversion. (A) Decrease (B) Increase (C) No change (D) Either (A) or (B), depends on the type of reaction

Last Answer : (C) No change

In case of a multipass shell and tube heat exchanger, providing a baffle on the shell side __________ the heat transfer rate. (A) Increases (B) Decreases (C) Does not affect (D) May increase or decrease, depends on the type of baffle

Description : In case of a multipass shell and tube heat exchanger, providing a baffle on the shell side __________ the heat transfer rate. (A) Increases (B) Decreases (C) Does not affect (D) May increase or decrease, depends on the type of baffle

Last Answer : (A) Increases

Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Description : Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Last Answer : (D) Boiling of a liquid on a hot surface

Smog is (A) Nothing but black smoke (B) A combination of smoke and fog (C) A liquid particle resulting from vapor condensation (D) A solid particle e.g. fly-ash

Description : Smog is (A) Nothing but black smoke (B) A combination of smoke and fog (C) A liquid particle resulting from vapor condensation (D) A solid particle e.g. fly-ash

Last Answer : (B) A combination of smoke and fog

Film condensation is promoted on a/an __________ surface. (A) Oily (B) Coated (C) Clean & smooth (D) Dirty

Description : Film condensation is promoted on a/an __________ surface. (A) Oily (B) Coated (C) Clean & smooth (D) Dirty

Last Answer : (C) Clean & smooth

Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Description : Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Last Answer : (C) Heat transfer co-efficient

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Mass transfer co-efficient (K) and diffusivity (D) are related according to film theory as (A) K ∝ D (B) K ∝√D (C) K ∝ D1.5 (D) K ∝ D

Description : Mass transfer co-efficient (K) and diffusivity (D) are related according to film theory as (A) K ∝ D (B) K ∝√D (C) K ∝ D1.5 (D) K ∝ D

Last Answer : (A) K ∝ D

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Description : If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Last Answer : (B) Always between h1 and h2

It is not preferable to use superheated steam in evaporators, because of its very (A) High temperature (B) High pressure (C) Low film co-efficient (D) None of these

Description : It is not preferable to use superheated steam in evaporators, because of its very (A) High temperature (B) High pressure (C) Low film co-efficient (D) None of these

Last Answer : (C) Low film co-efficient

If a solid-gas non-catalytic reaction occurs at very high temperature, the rate controlling step is the __________ diffusion. (A) Film (B) Ash layer (C) Pore (D) None of these

Description : If a solid-gas non-catalytic reaction occurs at very high temperature, the rate controlling step is the __________ diffusion. (A) Film (B) Ash layer (C) Pore (D) None of these

Last Answer : (A) Film

Horsepower increase of a centrifugal gas compressor without altering the volumetric flow rate will __________ the gas discharge pressure. (A) Increase (B) Decrease (C) Not change (D) Exponentially decrease

Description : Horsepower increase of a centrifugal gas compressor without altering the volumetric flow rate will __________ the gas discharge pressure. (A) Increase (B) Decrease (C) Not change (D) Exponentially decrease

Last Answer : (A) Increase