Difference Between Flywheel And Governor?

Difference Between Flywheel And Governor?
by

1 Answer

Answer :

The function of flywheel is to store the energy/power produced during the power stroke of an engine and this stored energy is used during remaining stroke to make piston up and down during working of engine while governor tries control the speed of an engine due to variation in load. It does this work by reducing or increasing the amount of fuel passing to the engine.
by

Related questions

Difference between Flywheel and Governor

Description : Difference between Flywheel and Governor

Last Answer : FLYWHEEL GOVERNOR 1.Function- To control the speed variations caused by fluctuations of engine turning moment during a cycle.  1.Function- To regulate the mean speed of engine within prescribed ... it.  6. Mathematically it controls δN/δt 6. Mathematically it controls δN

Which of the following is used to control the speed variations of the engine caused by the fluctuations of the engine turning moment? 1. D-slide valve 2. Governor 3. Flywheel 4. Meyer’s expansion valve

Description : Which of the following is used to control the speed variations of the engine caused by the fluctuations of the engine turning moment? 1. D-slide valve 2. Governor 3. Flywheel 4. Meyer’s expansion valve

Last Answer : 3. Flywheel

If the load on the engine is constant, the mean speed will be constant from the cycle, then (A) The governor will not operate but flywheel will be acting (B) The flywheel will be acting but governor will not operate (C) Both flywheel and governor will be acting (D) Both flywheel and governor will not be acting

Description : If the load on the engine is constant, the mean speed will be constant from the cycle, then (A) The governor will not operate but flywheel will be acting (B) The flywheel will be acting but ... (C) Both flywheel and governor will be acting (D) Both flywheel and governor will not be acting

Last Answer : (A) The governor will not operate but flywheel will be acting

Which of the following doesn’t waste energy? a) Flywheel b) Governor c) Both flywheel and governor d) Neither flywheel nor governor

Description : Which of the following doesn’t waste energy? a) Flywheel b) Governor c) Both flywheel and governor d) Neither flywheel nor governor

Last Answer : a) Flywheel

If load on the engine is constant, the mean speed will be constant and ___ will not operate. a) Flywheel b) Governor c) Both flywheel and governor d) None of the mentioned

Description : If load on the engine is constant, the mean speed will be constant and ___ will not operate. a) Flywheel b) Governor c) Both flywheel and governor d) None of the mentioned

Last Answer : b) Governor

Flywheel and governor can be interchanged. a) True b) False

Description : Flywheel and governor can be interchanged. a) True b) False

Last Answer : b) False

Difference Between Tube And Pipe?

Description : Difference Between Tube And Pipe?

Last Answer :  There always a debate between differentiation of pipe and tube. Pipe is always designated by its Inside Diameter (ID) because main purpose of pipe is to carry fluid, while the  Tube ... tolerances as to that of pipe and tubes are more costlier in manufacturing compared to pipe production.

What Is The Difference Between Heat Transfer And Thermodynamics?

Description : What Is The Difference Between Heat Transfer And Thermodynamics?

Last Answer : Heat transfer deals with the energy analysis which in transition and and depends on the modes of heat transfer like conduction, convection and radiation or combination of any modes. Heat transfer deals ... with study of system at equilibrium and does not depend on how heat transfer is calculated.

It is the unbalanced force developed in a turbo jet engine that is caused by the difference in the momentum of the low-velocity air entering the engine and the high velocity exhaust gases leaving the engine.  a. Fall  b. Lift  c. Drag  d. Thrust

Description : It is the unbalanced force developed in a turbo jet engine that is caused by the difference in the momentum of the low-velocity air entering the engine and the high velocity exhaust gases leaving the engine.  a. Fall  b. Lift  c. Drag  d. Thrust

Last Answer : Thrust

For a body cooling in a draft, the rate of heat loss is proportional to the difference in temperature between the body and its surroundings.  a. Nemst Effect  b. Caloric Theory  c. Joule’s Law  d. Newton’s Law of Cooling

Description : For a body cooling in a draft, the rate of heat loss is proportional to the difference in temperature between the body and its surroundings.  a. Nemst Effect  b. Caloric Theory  c. Joule’s Law  d. Newton’s Law of Cooling

Last Answer : Newton’s Law of Cooling

Which of the following events is heat exchange involved?  a. when there is a phase change  b. when there is a chemical reaction  c. when the gas expands adiabatically  d. when there is difference in temperature

Description : Which of the following events is heat exchange involved?  a. when there is a phase change  b. when there is a chemical reaction  c. when the gas expands adiabatically  d. when there is difference in temperature

Last Answer : when the gas expands adiabatically

Which of the following best describes heat?  a. The capacity to do work  b. Forces times distances  c. Sum of thermal and chemical energy  d. An energy transfer due to temperature difference

Description : Which of the following best describes heat?  a. The capacity to do work  b. Forces times distances  c. Sum of thermal and chemical energy  d. An energy transfer due to temperature difference

Last Answer : An energy transfer due to temperature difference

____________is the difference between the saturation temperature for the given pressure and the actual sub cooled liquid temperature.  a) Degrees of Superheat, °SH  b) Degrees of Sub cooled, °SB  c) Both a and b  d) None of the above

Description : ____________is the difference between the saturation temperature for the given pressure and the actual sub cooled liquid temperature.  a) Degrees of Superheat, °SH  b) Degrees of Sub cooled, °SB  c) Both a and b  d) None of the above

Last Answer : Degrees of Sub cooled, °SB

_____________ is the difference between the actual temperature of superheated vapor and the saturation temperature for the existing pressure.  a) Degrees of Superheat, °SH  b) Degrees of Sub cooled, °SB  c) Both a and b  d) None of the above

Description : _____________ is the difference between the actual temperature of superheated vapor and the saturation temperature for the existing pressure.  a) Degrees of Superheat, °SH  b) Degrees of Sub cooled, °SB  c) Both a and b  d) None of the above

Last Answer : Degrees of Superheat, °SH

A wall of the firebrick has an inside temperature of 313ºF and an outside temperature of 73ºF. What is the difference in the surface temperature in Rankin?  a. 70  b. 68  c. 72  d. 94 ºR = ºF + 460

Description : A wall of the firebrick has an inside temperature of 313ºF and an outside temperature of 73ºF. What is the difference in the surface temperature in Rankin?  a. 70  b. 68  c. 72  d. 94 ºR = ºF + 460

Last Answer : 70

The energy that flows from higher temperature object to a lower temperature object because of the difference in temperature is called  a. heat  b. temperature  c. thermodynamics cycle  d. energy flow

Description : The energy that flows from higher temperature object to a lower temperature object because of the difference in temperature is called  a. heat  b. temperature  c. thermodynamics cycle  d. energy flow

Last Answer : heat

What states that the net change in the total energy of the system during a process is equal to the difference between the total energy entering and the total energy leaving the system during that process?  A. Third law of thermodynamics  B. Conservation of energy principle  C. Second law of thermodynamics  D. Conservation of mass principle

Description : What states that the net change in the total energy of the system during a process is equal to the difference between the total energy entering and the total energy leaving the system during ... Conservation of energy principle  C. Second law of thermodynamics  D. Conservation of mass principle

Last Answer : Conservation of energy principle

The difference between the absolute pressure and the atmospheric pressure is called the _____ pressure.  A. Gage  B. Normal  C. Standard  D. Vacuum

Description : The difference between the absolute pressure and the atmospheric pressure is called the _____ pressure.  A. Gage  B. Normal  C. Standard  D. Vacuum

Last Answer : Gage

The prefix “iso” used to designate a process means ______.  A. Cannot be interchanged  B. Remains constant  C. Approximately equal  D. Slight difference

Description : The prefix “iso” used to designate a process means ______.  A. Cannot be interchanged  B. Remains constant  C. Approximately equal  D. Slight difference

Last Answer : Remains constant

The gas constant (R) is equal to the __________ of two specific heats.  A. sum  B. difference  C. product  D. ratio

Description : The gas constant (R) is equal to the __________ of two specific heats.  A. sum  B. difference  C. product  D. ratio

Last Answer : Answer: B

The greater the pressure difference in throttling, the lesser is the irreversibility.  A. Yes  B. No

Description : The greater the pressure difference in throttling, the lesser is the irreversibility.  A. Yes  B. No

Last Answer : Answer: B

The thermodynamic difference between a Rankine cycle working with saturated steam and the Carnot cycle is that  (a) carnot cycle can’t work with saturated steam  (b) heat is supplied to water at temperature below the maximum temperature of the cycle  (c) a rankine cycle receives heat at two places  (d) rankine cycle is hypothetical  (e) none of the above.

Description : The thermodynamic difference between a Rankine cycle working with saturated steam and the Carnot cycle is that  (a) carnot cycle can't work with saturated steam  (b) heat is supplied to water at temperature ... heat at two places  (d) rankine cycle is hypothetical  (e) none of the above.

Last Answer : Answer : b

Carnot cycle efficiency is maximum when  (a) initial temperature is 0°K  (b) final temperature is 0°K  (c) difference between initial and final temperature is 0°K  (d) final temperature is 0°C  (e) initial temperature is minimum possible.

Description : Carnot cycle efficiency is maximum when  (a) initial temperature is 0°K  (b) final temperature is 0°K  (c) difference between initial and final temperature is 0°K  (d) final temperature is 0°C  (e) initial temperature is minimum possible.

Last Answer : Answer : b

For a thermodynamic process to be reversible, the temperature difference between hot body and working substance should be  (a) zero  (b) minimum  (d) maximum  (d) infinity  (e) there is no such criterion.

Description : For a thermodynamic process to be reversible, the temperature difference between hot body and working substance should be  (a) zero  (b) minimum  (d) maximum  (d) infinity  (e) there is no such criterion.

Last Answer : Answer : a

The coefficient of fluctuation of energy of flywheel is 1. ratio of maximum fluctuation of energy to work done per cycle 2. ratio of to work done per cycle to maximum fluctuation of energy 3. difference between maximum and minimum kinetic energy during the cycle 4. ratio of maximum and minimum kinetic energy during the cycle

Description : The coefficient of fluctuation of energy of flywheel is 1. ratio of maximum fluctuation of energy to work done per cycle 2. ratio of to work done per cycle to maximum fluctuation of energy ... minimum kinetic energy during the cycle 4. ratio of maximum and minimum kinetic energy during the cycle

Last Answer : 1. ratio of maximum fluctuation of energy to work done per cycle

The maximum fluctuation of energy of flywheel is 1. difference between maximum and minimum kinetic energy during the cycle 2. difference between maximum and mean kinetic energy during the cycle 3. difference between mean and minimum kinetic energy during the cycle 4. mean of maximum and minimum kinetic energy during the cycle

Description : The maximum fluctuation of energy of flywheel is 1. difference between maximum and minimum kinetic energy during the cycle 2. difference between maximum and mean kinetic energy during the cycle 3. ... kinetic energy during the cycle 4. mean of maximum and minimum kinetic energy during the cycle

Last Answer : 1. difference between maximum and minimum kinetic energy during the cycle

The coefficient of fluctuation of energy of flywheel is, (A) Ratio of maximum fluctuation of energy to work done per cycle (B) Ratio of to work done per cycle to maximum fluctuation of energy (C) Difference between maximum and minimum kinetic energy during the cycle (D) Ratio of maximum and minimum kinetic energy during the cycle

Description : The coefficient of fluctuation of energy of flywheel is, (A) Ratio of maximum fluctuation of energy to work done per cycle (B) Ratio of to work done per cycle to maximum fluctuation of ... minimum kinetic energy during the cycle (D) Ratio of maximum and minimum kinetic energy during the cycle

Last Answer : (A) Ratio of maximum fluctuation of energy to work done per cycle

The maximum fluctuation of speed of flywheel is, (A) Difference between maximum and minimum speeds during the cycle (B) Difference between maximum and mean speeds during the cycle (C) Difference between mean and minimum speeds during the cycle (D) Mean of maximum and minimum speeds during the cycle

Description : The maximum fluctuation of speed of flywheel is, (A) Difference between maximum and minimum speeds during the cycle (B) Difference between maximum and mean speeds during the cycle (C) Difference ... and minimum speeds during the cycle (D) Mean of maximum and minimum speeds during the cycle

Last Answer : (A) Difference between maximum and minimum speeds during the cycle

The maximum fluctuation of energy of flywheel is, (A) Difference between maximum and minimum kinetic energy during the cycle (B) Difference between maximum and mean kinetic energy during the cycle (C) Difference between mean and minimum kinetic energy during the cycle (D) Mean of maximum and minimum kinetic energy during the cycle

Description : The maximum fluctuation of energy of flywheel is, (A) Difference between maximum and minimum kinetic energy during the cycle (B) Difference between maximum and mean kinetic energy during the cycle ... kinetic energy during the cycle (D) Mean of maximum and minimum kinetic energy during the cycle

Last Answer : (A) Difference between maximum and minimum kinetic energy during the cycle

In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these

Description : In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these

Last Answer : (B) Higher than

What Is The Function Of Forebay?

Description : What Is The Function Of Forebay?

Last Answer : Forebay is considered as naturally provided surge tank. It is temporary water storage when the load on the plant is reduced and provides water for initial increment on increasing load.

What Is The Use Of Surge Tank?

Description : What Is The Use Of Surge Tank?

Last Answer : The surge tank is used to provide better regulation of water pressure in the system. The surge tank controls the water when the load on the turbine decreases and supplies water when the ... variations resulting from the rapid changes in water flow in penstock and hence prevents water hammer.

Why Trash Rack Is Used?

Description : Why Trash Rack Is Used?

Last Answer : The trash rack is used to prevent the entry of debris, which might damage the turbine runners and chock up the nozzle of impulse turbine.

What Is The Main Purpose Of The Dam?

Description : What Is The Main Purpose Of The Dam?

Last Answer : The main purpose of the dam is to increase the height of water level and also to increase the working head of the hydraulic power plant.

What Is The Main Purpose Of The Reservoir?

Description : What Is The Main Purpose Of The Reservoir?

Last Answer : The main purpose of reservoir is to store water received from catchments areas during the rainy seasons and supply the same during the dry season.

What Consists Of Cooling Water Circuit And Coal & Ash Circuit In Steam Power Plant?

Description : What Consists Of Cooling Water Circuit And Coal & Ash Circuit In Steam Power Plant?

Last Answer : The cooling water circuit consists of a pump, condenser and cooling tower. The coal and ash circuit consists of coal delivery, preparation of coal, handling of coal to the boiler furnace, ash handling and ash storage.

What Consists Of Feed Water And Steam Flow Circuit In Steam Power?

Description : What Consists Of Feed Water And Steam Flow Circuit In Steam Power?

Last Answer : The feed water and steam flow circuit consists of feed pump, economizer boiler drum super heater, turbine and condenser.

What Consists Of Air And Flue Gas Circuit?

Description : What Consists Of Air And Flue Gas Circuit?

Last Answer : Air and flue gas circuit consists of forced draught fan, air preheater, boiler, furnace, superheater, economizer, dust collector, induced draught fan and chimney.

Name The Four Major Circuits In Steam Power Plant?

Description : Name The Four Major Circuits In Steam Power Plant?

Last Answer :  Coal and ash circuit  Air and flue gas circuit  Feed water and steam circuit  Cooling water circuit

What Is Ductile-brittle Transition Temperature?

Description : What Is Ductile-brittle Transition Temperature?

Last Answer : It is the temperature below which the tendency of a material to fracture increases rather than forming. Below this temperature the material loses its ductility. It is also called Nil Ductility Temperature

Define Torque.?

Description : Define Torque.?

Last Answer : Torque is defined as a force applied to an object that results in rotational motion.

What Is Annealing?

Description : What Is Annealing?

Last Answer : It is a process of heating a material above the re-crystallization temperature and cooling after a specific time interval. This increases the hardness and strength if the material.

What Is Gear Ratio?

Description : What Is Gear Ratio?

Last Answer : It is the ratio of the number of revolutions of the pinion gear to one revolution of the idler gear.

Explain The Nomenclature Of A 6203-zz Bearing?

Description : Explain The Nomenclature Of A 6203-zz Bearing?

Last Answer : 6 is the type code, which shows it is a single-row ball bearing, 2 is the series, means light, 03 is the bore, which is 17 mm and ZZ is the suffix meaning double shielded bearing.

Explain Otto Cycle?

Description : Explain Otto Cycle?

Last Answer : Otto cycle can be explained by a pressure volume relationship diagram. It shows the functioning cycle of a four stroke engine. The cycle starts with an intake stroke, closing the intake and moving to ... heat is rejected and the exhaust stroke. It was designed by Nicolas Otto, a German engineer.

What Is Ps ?

Description : What Is Ps ?

Last Answer : PS is Pferdestarke, the German unit for Horsepower.

How Many Joules Is 1 Btu?

Description : How Many Joules Is 1 Btu?

Last Answer : 1 BTU is equal to 1055.056 joules.

What Is A Newtonian Fluid?

Description : What Is A Newtonian Fluid?

Last Answer : A Newtonian fluid possesses a linear stress strain relationship curve and it passes through the origin. The fluid properties of a Newtonian fluid do not change when any force acts upon it.

Define Reynolds Number.?

Description : Define Reynolds Number.?

Last Answer : Reynolds number is the ratio of inertial force and viscous force. It is a dimensionless number. It determines the type of fluid flow.

What Are The Points In The Stress Strain Curve For Steel?

Description : What Are The Points In The Stress Strain Curve For Steel?

Last Answer : Proportional limit, elastic limit or yield point, ultimate stress and stress at failure.