What Is Gear Ratio?

What Is Gear Ratio?
by

1 Answer

Answer :

It is the ratio of the number of revolutions of the pinion gear to one revolution of the idler gear.
by

Related questions

Why Poisson Ratio Is Higher In, Rubber/steel/wood?

Description : Why Poisson Ratio Is Higher In, Rubber/steel/wood?

Last Answer : When a material is compressed in one direction, it usuallytends to expand in the other two directions perpendicular tothe direction of compression. This phenomenon is called the Poisson effect. Poisson's ratio is a ... For steel = 0.288 For wood < 0.2 Thus Poisson's ratio is higher in RUBBER.

Is a steady flow process at total constant pressure through a control volume for which there is no heat?  a. Adiabatic Saturation Process  b. Dew point  c. Adiabatic Ratio  d. None of the above

Description : Is a steady flow process at total constant pressure through a control volume for which there is no heat?  a. Adiabatic Saturation Process  b. Dew point  c. Adiabatic Ratio  d. None of the above

Last Answer : Adiabatic Saturation Process

Also called absolute humidity and specific humidity.  a. Related humidity  b. Humidity ratio  c. Dew point  d. Adiabatic ratio

Description : Also called absolute humidity and specific humidity.  a. Related humidity  b. Humidity ratio  c. Dew point  d. Adiabatic ratio

Last Answer : Humidity ratio

Is define as the ratio of the actual pressure of the vapor  a. Relative Humidity  b. Humidity Ratio  c. Dew Point  d. Adiabatic Saturation

Description : Is define as the ratio of the actual pressure of the vapor  a. Relative Humidity  b. Humidity Ratio  c. Dew Point  d. Adiabatic Saturation

Last Answer : Relative Humidity

The ratio of the weight of a substance to the weight of some standard substance is called?  a. Specific Heat  b. Specific Gravity  c. Isothermal  d. Specific Weight

Description : The ratio of the weight of a substance to the weight of some standard substance is called?  a. Specific Heat  b. Specific Gravity  c. Isothermal  d. Specific Weight

Last Answer : Specific Gravity

Specific heat ratio is always  a. > 1  b. < 1  c. = 1  d. none of the above

Description : Specific heat ratio is always  a. > 1  b. < 1  c. = 1  d. none of the above

Last Answer : > 1

The ratio of the change in energy in the form of the heat  a. relative density  b. specific heat  c. specific gravity  d. none of the above

Description : The ratio of the change in energy in the form of the heat  a. relative density  b. specific heat  c. specific gravity  d. none of the above

Last Answer : specific heat

Helium ( R= 0.4698 BTU/lbm-˚R ) is compressed isothermally from 14.7 psia and 68 ˚F. The compression ratio is 1:4. Calculate the work done by the gas.  A. –1454 BTU/lbm  B. -364 BTU/lbm  C.-187BTU/lbm  D.46.7 BTU/lbm Formula: W = RT ln (V2/V1)

Description : Helium ( R= 0.4698 BTU/lbm-˚R ) is compressed isothermally from 14.7 psia and 68 ˚F. The compression ratio is 1:4. Calculate the work done by the gas.  A. –1454 BTU/lbm  B. -364 BTU/lbm  C.-187BTU/lbm  D.46.7 BTU/lbm Formula: W = RT ln (V2/V1)

Last Answer : -364 BTU/lbm

Defined as the ratio of weight of dry steam to the weight of stuff.  a. dryness fraction  b. Vaporization  c. fusion  d. super heated steam

Description : Defined as the ratio of weight of dry steam to the weight of stuff.  a. dryness fraction  b. Vaporization  c. fusion  d. super heated steam

Last Answer : dryness fraction

What is defined as the ratio of the change in temperature to the change in pressure when a real gas is throttled?  A. Rankine coefficient  B. Kelvin coefficient  C. Maxwell-Boltzmann coefficient  D. Joule-Thomson coefficient

Description : What is defined as the ratio of the change in temperature to the change in pressure when a real gas is throttled?  A. Rankine coefficient  B. Kelvin coefficient  C. Maxwell-Boltzmann coefficient  D. Joule-Thomson coefficient

Last Answer : Joule-Thomson coefficient

The coefficient of performance (COP) is the ratio between the:  A. Power consumption in watts and heat absorbed per hour  B. Heat absorbed per hour and the power consumption in watts  C. Work required and the absorbed heat  D. Absorbed heat and work required

Description : The coefficient of performance (COP) is the ratio between the:  A. Power consumption in watts and heat absorbed per hour  B. Heat absorbed per hour and the power consumption in watts  C. Work required and the absorbed heat  D. Absorbed heat and work required

Last Answer : Absorbed heat and work required

Which one is the correct relation between energy efficiency ratio (EER) and coefficient of performance (COP)?  A. EER = 2.34 COP  B. EER = 3.24 COP  C. EER = 3.42 COP  D. EER = 4.23 COP

Description : Which one is the correct relation between energy efficiency ratio (EER) and coefficient of performance (COP)?  A. EER = 2.34 COP  B. EER = 3.24 COP  C. EER = 3.42 COP  D. EER = 4.23 COP

Last Answer : EER = 3.42 COP

What is defined as the ratio of the net electrical power output to the rate of fuel energy input?  A. Combustion efficiency  B. Thermal efficiency  C. Overall efficiency  D. Furnace efficiency

Description : What is defined as the ratio of the net electrical power output to the rate of fuel energy input?  A. Combustion efficiency  B. Thermal efficiency  C. Overall efficiency  D. Furnace efficiency

Last Answer : Overall efficiency

What is the ratio of the useful heat extracted to heating value?  A. Combustion efficiency  B. Phase efficiency  C. Heat efficiency  D. Work efficiency

Description : What is the ratio of the useful heat extracted to heating value?  A. Combustion efficiency  B. Phase efficiency  C. Heat efficiency  D. Work efficiency

Last Answer : Combustion efficiency

Thermal efficiency is the ratio of:  A. Network input to total heat input  B. Network output to total heat output  C. Network output to total heat input  D. Network input to total heat output

Description : Thermal efficiency is the ratio of:  A. Network input to total heat input  B. Network output to total heat output  C. Network output to total heat input  D. Network input to total heat output

Last Answer : Network output to total heat input

The gas constant of a certain gas is the ratio of:  A. Universal gas constant to molar mass  B. Universal gas constant to atomic weight  C. Universal gas constant to atomic number  D. Universal gas constant to number of moles

Description : The gas constant of a certain gas is the ratio of:  A. Universal gas constant to molar mass  B. Universal gas constant to atomic weight  C. Universal gas constant to atomic number  D. Universal gas constant to number of moles

Last Answer : Universal gas constant to molar mass

The ratio of the mass of vapor to the total mass of the mixture is called ______.  A. Vapor ratio  B. Vapor content  C. Vapor index  D. Quality

Description : The ratio of the mass of vapor to the total mass of the mixture is called ______.  A. Vapor ratio  B. Vapor content  C. Vapor index  D. Quality

Last Answer : Quality

The efficiency of Diesel cycle depends upon  A. temperature limits  B. pressure ratio  C. compression ratio  D. cut-off ratio and compression ratio

Description : The efficiency of Diesel cycle depends upon  A. temperature limits  B. pressure ratio  C. compression ratio  D. cut-off ratio and compression ratio

Last Answer : Answer: D

The efficiency of a dual combustion cycle __________ upon cut-off ratio.  A. depends  B. does not depend

Description : The efficiency of a dual combustion cycle __________ upon cut-off ratio.  A. depends  B. does not depend

Last Answer : Answer: A

The gas constant (R) is equal to the __________ of two specific heats.  A. sum  B. difference  C. product  D. ratio

Description : The gas constant (R) is equal to the __________ of two specific heats.  A. sum  B. difference  C. product  D. ratio

Last Answer : Answer: B

Otto cycle efficiency is higher than Diesel cycle efficiency for the same compression ratio and heat input because in Otto cycle  A. combustion is at constant volume  B. expansion and compression are isentropic  C. maximum temperature is higher  D. heat rejection is lower

Description : Otto cycle efficiency is higher than Diesel cycle efficiency for the same compression ratio and heat input because in Otto cycle  A. combustion is at constant volume  B. expansion and compression are isentropic  C. maximum temperature is higher  D. heat rejection is lower

Last Answer : Answer: D

The compression ratio for Diesel engines is  A. 3 to 6  B. 5 to 8  C. 15 to 20  D. 20 to 30

Description : The compression ratio for Diesel engines is  A. 3 to 6  B. 5 to 8  C. 15 to 20  D. 20 to 30

Last Answer : Answer: C

When cut-off ratio is __________ the efficiency of Diesel cycle approaches to Otto cycle efficiency.  A. zero  B. 1/5  C. 4/5  D. 1

Description : When cut-off ratio is __________ the efficiency of Diesel cycle approaches to Otto cycle efficiency.  A. zero  B. 1/5  C. 4/5  D. 1

Last Answer : Answer: A

The ratio of specific heat at constant pressure (Cp) and specific heat at constant volume (cv) is  A. equal to one  B. less than one  C. greater than one  D. none of these

Description : The ratio of specific heat at constant pressure (Cp) and specific heat at constant volume (cv) is  A. equal to one  B. less than one  C. greater than one  D. none of these

Last Answer : Answer: C

The compression ratio for petrol engines is  A.3 to 6  B.5 to 8  C.15 to 20  D.20 to 30

Description : The compression ratio for petrol engines is  A.3 to 6  B.5 to 8  C.15 to 20  D.20 to 30

Last Answer : Answer: B

The efficiency and work ratio of a simple gas turbine cycle are  A.low  B.very low  C.high  D.very high

Description : The efficiency and work ratio of a simple gas turbine cycle are  A.low  B.very low  C.high  D.very high

Last Answer : Answer: B

The ideal efficiency of a Brayton cycle with regeneration, with increase in pressure ratio will  (a) increase  (b) decrease  (c) remain unchanged  (d) increase/decrease depending on ap-plication  (e) unpredictable. “

Description : The ideal efficiency of a Brayton cycle with regeneration, with increase in pressure ratio will  (a) increase  (b) decrease  (c) remain unchanged  (d) increase/decrease depending on ap-plication  (e) unpredictable. “

Last Answer : Answer : b

The ideal efficiency of a Brayton cycle without regeneration with increase ni pressure ratio will

Description : The ideal efficiency of a Brayton cycle without regeneration with increase ni pressure ratio will  (a) increase  (b) decrease  (c) remain unchanged  (d) increase/decrease depending on application  (e) unpredictable.

Last Answer : Answer : a

For same compression ratio and for same heat added  (a) Otto cycle is more efficient than Diesel cycle  (b) Diesel cycle is more efficient than Otto cycle  (c) efficiency depends on other factors  (d) both Otto and Diesel cycles are equally efficient  (e) none of the above.

Description : For same compression ratio and for same heat added  (a) Otto cycle is more efficient than Diesel cycle  (b) Diesel cycle is more efficient than Otto cycle  (c) efficiency depends on other factors  (d) both Otto and Diesel cycles are equally efficient  (e) none of the above.

Last Answer : Answer : a

Universal gas constant is defined as equal to product of the molecular weight of the gas and  (a) specific heat at constant pressure  (b) specific heat at constant volume  (c) ratio of two specific heats  (d) gas constant  (e) unity.

Description : Universal gas constant is defined as equal to product of the molecular weight of the gas and  (a) specific heat at constant pressure  (b) specific heat at constant volume  (c) ratio of two specific heats  (d) gas constant  (e) unity.

Last Answer : Answer : d

The index of compression n tends to reach ratio of specific heats y when  (a) flow is uniform and steady  (b) process is isentropic  (c) process is isothermal  (d) process is isentropic and specific heat does not change with temperature  (e) process is isentropic and specific heat changes with temperature.

Description : The index of compression n tends to reach ratio of specific heats y when  (a) flow is uniform and steady  (b) process is isentropic  (c) process is isothermal  (d) process ... specific heat does not change with temperature  (e) process is isentropic and specific heat changes with temperature.

Last Answer : Answer : d

The ratio of two specific heats of air is equal to  (a) 0.17  (b) 0.24  (c) 0.1  (d) 1.41  (e) 2.71.

Description : The ratio of two specific heats of air is equal to  (a) 0.17  (b) 0.24  (c) 0.1  (d) 1.41  (e) 2.71.

Last Answer : Answer : d

While ascending a hill, the driver of the vehicle keeps the gear ratio – (1) equal to 1 (2) less than 1 (3) greater than 1 (4) either equal to or greater than 1

Description : While ascending a hill, the driver of the vehicle keeps the gear ratio – (1) equal to 1 (2) less than 1 (3) greater than 1 (4) either equal to or greater than 1

Last Answer : (4) either equal to or greater than 1 Explanation: While ascending a hill Gear Ratio should be "Either equal to or greater than 1?. Gear Ratio is the ratio between angular velocity of input gear to the angular velocity of output gear. It prevents the vehicle from stalling.

In an epicycle gear reduction unit, the ratio of the number of teeth of the internal gears to the sun gear is: a) 3:1 b) 4:1 c) 2.5:1 d) 4.5:1

Description : In an epicycle gear reduction unit, the ratio of the number of teeth of the internal gears to the sun gear is: a) 3:1 b) 4:1 c) 2.5:1 d) 4.5:1

Last Answer : b) 4:1

While ascending a hill, the driver of the vehicle keeps the gear ratio (1) equal to 1 (2) less than 1 (3) greater than 1 (4) either equal to or greater than 1

Description : While ascending a hill, the driver of the vehicle keeps the gear ratio (1) equal to 1 (2) less than 1 (3) greater than 1 (4) either equal to or greater than 1

Last Answer : either equal to or greater than 1

In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these

Description : In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these

Last Answer : (B) Higher than

What Is The Function Of Forebay?

Description : What Is The Function Of Forebay?

Last Answer : Forebay is considered as naturally provided surge tank. It is temporary water storage when the load on the plant is reduced and provides water for initial increment on increasing load.

What Is The Use Of Surge Tank?

Description : What Is The Use Of Surge Tank?

Last Answer : The surge tank is used to provide better regulation of water pressure in the system. The surge tank controls the water when the load on the turbine decreases and supplies water when the ... variations resulting from the rapid changes in water flow in penstock and hence prevents water hammer.

Why Trash Rack Is Used?

Description : Why Trash Rack Is Used?

Last Answer : The trash rack is used to prevent the entry of debris, which might damage the turbine runners and chock up the nozzle of impulse turbine.

What Is The Main Purpose Of The Dam?

Description : What Is The Main Purpose Of The Dam?

Last Answer : The main purpose of the dam is to increase the height of water level and also to increase the working head of the hydraulic power plant.

What Is The Main Purpose Of The Reservoir?

Description : What Is The Main Purpose Of The Reservoir?

Last Answer : The main purpose of reservoir is to store water received from catchments areas during the rainy seasons and supply the same during the dry season.

What Consists Of Cooling Water Circuit And Coal & Ash Circuit In Steam Power Plant?

Description : What Consists Of Cooling Water Circuit And Coal & Ash Circuit In Steam Power Plant?

Last Answer : The cooling water circuit consists of a pump, condenser and cooling tower. The coal and ash circuit consists of coal delivery, preparation of coal, handling of coal to the boiler furnace, ash handling and ash storage.

What Consists Of Feed Water And Steam Flow Circuit In Steam Power?

Description : What Consists Of Feed Water And Steam Flow Circuit In Steam Power?

Last Answer : The feed water and steam flow circuit consists of feed pump, economizer boiler drum super heater, turbine and condenser.

What Consists Of Air And Flue Gas Circuit?

Description : What Consists Of Air And Flue Gas Circuit?

Last Answer : Air and flue gas circuit consists of forced draught fan, air preheater, boiler, furnace, superheater, economizer, dust collector, induced draught fan and chimney.

Name The Four Major Circuits In Steam Power Plant?

Description : Name The Four Major Circuits In Steam Power Plant?

Last Answer :  Coal and ash circuit  Air and flue gas circuit  Feed water and steam circuit  Cooling water circuit

What Is Ductile-brittle Transition Temperature?

Description : What Is Ductile-brittle Transition Temperature?

Last Answer : It is the temperature below which the tendency of a material to fracture increases rather than forming. Below this temperature the material loses its ductility. It is also called Nil Ductility Temperature

Define Torque.?

Description : Define Torque.?

Last Answer : Torque is defined as a force applied to an object that results in rotational motion.

What Is Annealing?

Description : What Is Annealing?

Last Answer : It is a process of heating a material above the re-crystallization temperature and cooling after a specific time interval. This increases the hardness and strength if the material.

Explain The Nomenclature Of A 6203-zz Bearing?

Description : Explain The Nomenclature Of A 6203-zz Bearing?

Last Answer : 6 is the type code, which shows it is a single-row ball bearing, 2 is the series, means light, 03 is the bore, which is 17 mm and ZZ is the suffix meaning double shielded bearing.

Explain Otto Cycle?

Description : Explain Otto Cycle?

Last Answer : Otto cycle can be explained by a pressure volume relationship diagram. It shows the functioning cycle of a four stroke engine. The cycle starts with an intake stroke, closing the intake and moving to ... heat is rejected and the exhaust stroke. It was designed by Nicolas Otto, a German engineer.