What Consists Of Air And Flue Gas Circuit?

What Consists Of Air And Flue Gas Circuit?
by

1 Answer

Answer :

Air and flue gas circuit consists of forced draught fan, air preheater, boiler, furnace, superheater, economizer, dust collector, induced draught fan and chimney.
by

Related questions

What consists of air and flue gas circuit?

Description : What consists of air and flue gas circuit?

Last Answer : Air and flue gas circuit consists of forced draught fan, air-pre-heater, boiler, furnace, super heater, economizer, dust collector, induced draught fan and chimney.

What consists of air and flue gas circuit?

Description : What consists of air and flue gas circuit?

Last Answer : Air and flue gas circuit consists of forced draught fan, air-pre-heater, boiler, furnace, super heater, economiser, dust collector, induced draught fan and chimney.

What Consists Of Cooling Water Circuit And Coal & Ash Circuit In Steam Power Plant?

Description : What Consists Of Cooling Water Circuit And Coal & Ash Circuit In Steam Power Plant?

Last Answer : The cooling water circuit consists of a pump, condenser and cooling tower. The coal and ash circuit consists of coal delivery, preparation of coal, handling of coal to the boiler furnace, ash handling and ash storage.

What Consists Of Feed Water And Steam Flow Circuit In Steam Power?

Description : What Consists Of Feed Water And Steam Flow Circuit In Steam Power?

Last Answer : The feed water and steam flow circuit consists of feed pump, economizer boiler drum super heater, turbine and condenser.

To convert volumetric analysis to gravimetric analysis, the relative volume of each constituent of the flue gases is  (a) divided by its molecular weight  (b) multiplied by its molecular weight  (c) multiplied by its density  (d) multiplied by its specific weight  (e) divided by its specific weight.

Description : To convert volumetric analysis to gravimetric analysis, the relative volume of each constituent of the flue gases is  (a) divided by its molecular weight  (b) multiplied by its molecular weight  (c) ... by its density  (d) multiplied by its specific weight  (e) divided by its specific weight.

Last Answer : Answer : b

Carbonisation of coal consists of  A. drying and crushing the coal to a fine powder  B. moulding the finely ground coal under pressure with or without a binding material  C. heating the wood with a limited supply of air to temperature not less than 280°C  D. none of the above

Description : Carbonisation of coal consists of  A. drying and crushing the coal to a fine powder  B. moulding the finely ground coal under pressure with or without a binding material  C. heating the wood with a limited supply of air to temperature not less than 280°C  D. none of the above

Last Answer : Answer: D

Gas turbine cycle consists of  (a) two isothermals and two isentropics  (b) two isentropics and two constant volumes  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pressures  (e) none of the above.

Description : Gas turbine cycle consists of  (a) two isothermals and two isentropics  (b) two isentropics and two constant volumes  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pressures  (e) none of the above.

Last Answer : Answer : d

What pressure measuring device consists of a coiled hollow tube that tends to straighten out when the tube is subjected to an internal pressure?  A. Aneroid  B. Manometer  C. Bourdon pressure gage  D. Barometer

Description : What pressure measuring device consists of a coiled hollow tube that tends to straighten out when the tube is subjected to an internal pressure?  A. Aneroid  B. Manometer  C. Bourdon pressure gage  D. Barometer

Last Answer : Bourdon pressure gage

A system which consists of fixed amount of mass and no mass can cross its boundary called _____.  A. Equilibrium system  B. Thermal equilibrium system  C. Open system  D. Closed system

Description : A system which consists of fixed amount of mass and no mass can cross its boundary called _____.  A. Equilibrium system  B. Thermal equilibrium system  C. Open system  D. Closed system

Last Answer : Closed system

The dual combustion cycle consists of one constant pressure, two constant volume and two isentropic processes.  A. Agree  B. Disagree

Description : The dual combustion cycle consists of one constant pressure, two constant volume and two isentropic processes.  A. Agree  B. Disagree

Last Answer : Answer: A

Ericsson cycle consists of two constant pressure and two isothermal processes.  A. Agree  B. Disagree

Description : Ericsson cycle consists of two constant pressure and two isothermal processes.  A. Agree  B. Disagree

Last Answer : Answer: A

Brayton cycle consists’ of following four processes  (a) two isothermals and two isentropics  (b) two isentropics and two constant volumes  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pres-sures  (e) none of the above.

Description : Brayton cycle consists’ of following four processes  (a) two isothermals and two isentropics  (b) two isentropics and two constant volumes  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pres-sures  (e) none of the above.

Last Answer : Answer : d

Diesel cycle consists of following four processes  (a) two isothermals and two isentropics  (b) two isentropics, and two constant volumes.  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pressures  (e) none of the above.

Description : Diesel cycle consists of following four processes  (a) two isothermals and two isentropics  (b) two isentropics, and two constant volumes.  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pressures  (e) none of the above.

Last Answer : Answer : c

Otto cycle consists of following four processes  (a) two isothermals and two isentropics  (b) two isentropics and two constant volumes  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pres-sures  (e) none of the above.

Description : Otto cycle consists of following four processes  (a) two isothermals and two isentropics  (b) two isentropics and two constant volumes  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pres-sures  (e) none of the above.

Last Answer : Answer : b

The pressure gauge on a 2000 m³ tank of oxygen gas reads 600 kPa. How much volumes will the oxygen occupied at pressure of the outside air 100 kPa?  a) 14026.5 m³  b) 15026.5 m³  c) 13026.5 m³  d) 16026.5 m³ Formula: P1V1/T1 =P2V2/T2

Description : The pressure gauge on a 2000 m³ tank of oxygen gas reads 600 kPa. How much volumes will the oxygen occupied at pressure of the outside air 100 kPa?  a) 14026.5 m³  b) 15026.5 m³  c) 13026.5 m³  d) 16026.5 m³ Formula: P1V1/T1 =P2V2/T2

Last Answer : 14026.5 m³

3.0 lbm of air are contained at 25 psia and 100 ˚F. Given that Rair = 53.35 ft-lbf/lbm- ˚F, what is the volume of the container?  A.10.7 ft^3  B.14.7 ft^3  C.15 ft^3  D.24.9 ft^3 Formula: use the ideal gas law pV = mRT T = (100 +460) ˚R V = mRT/p

Description : 3.0 lbm of air are contained at 25 psia and 100 ˚F. Given that Rair = 53.35 ft-lbf/lbm- ˚F, what is the volume of the container?  A.10.7 ft^3  B.14.7 ft^3  C.15 ft^3  D.24.9 ft^3 Formula: use the ideal gas law pV = mRT T = (100 +460) ˚R V = mRT/p

Last Answer : 24.9 ft^3

If air is at pressure, p, of 3200 lbf/ft2 , and at a temperature, T, of 800 ˚R, what is the specific volume, v? (R=5303 ft-lbf/lbm-˚R, and air can be modeled as an ideal gas.)  A.9.8 ft^3/lbm  B.11.2 ft^3/lbm  C.13.33 ft^3/lbm  D.14.2 ft^3/lbm Formula: pv = RT v = RT / p

Description : If air is at pressure, p, of 3200 lbf/ft2 , and at a temperature, T, of 800 ˚R, what is the specific volume, v? (R=5303 ft-lbf/lbm-˚R, and air can be modeled as an ideal gas.)  A.9.8 ft^3/lbm  B.11.2 ft^3/lbm  C.13.33 ft^3/lbm  D.14.2 ft^3/lbm Formula: pv = RT v = RT / p

Last Answer : 13.33 ft^3/lbm

Producer gas is obtained by  A. partial combustion of coal, coke, anthracite coal or charcoal in a mixed air steam blast  B. carbonisation of bituminous coal  C. passing steam over incandescent coke  D. passing air and a large amount of steam over waste coal at about 650°C

Description : Producer gas is obtained by  A. partial combustion of coal, coke, anthracite coal or charcoal in a mixed air steam blast  B. carbonisation of bituminous coal  C. passing steam over incandescent coke  D. passing air and a large amount of steam over waste coal at about 650°C

Last Answer : Answer: A

Producer gas is obtained by  A. partial combustion of coal, coke, anthracite coal or charcoal in a mixed air steam blast  B. carbonisation of bituminous coal  C. passing steam over incandescent coke  D. passing air and a large amount of steam over waste coal at about 650°C

Description : Producer gas is obtained by  A. partial combustion of coal, coke, anthracite coal or charcoal in a mixed air steam blast  B. carbonisation of bituminous coal  C. passing steam over incandescent coke  D. passing air and a large amount of steam over waste coal at about 650°C

Last Answer : Answer: A

Water gas is obtained by passing air and a large amount of steam over waste coal at about 650°C.  A.Correct  B.Incorrect

Description : Water gas is obtained by passing air and a large amount of steam over waste coal at about 650°C.  A.Correct  B.Incorrect

Last Answer : Answer: B

Which of the following can be regarded as gas so that gas laws could be applicable, within the commonly encountered temperature limits.  (a) 02, N2, steam, C02  (b) Oz, N2, water vapour  (c) S02, NH3, C02, moisture  (d) 02, N2, H2, air  (e) steam vapours, H2, C02.

Description : Which of the following can be regarded as gas so that gas laws could be applicable, within the commonly encountered temperature limits.  (a) 02, N2, steam, C02  (b) Oz, N2, water vapour  (c) S02, NH3, C02, moisture  (d) 02, N2, H2, air  (e) steam vapours, H2, C02.

Last Answer : Answer : d

In regenerative air preheater (as practised in heating of coke ovens), the heat is transferred (A) Through a metallic wall (B) By direct contact of hot flue gas with air (C) By heating an intermediate material (like chequor bricks) and then heating the air from this hot material (D) None of these

Description : In regenerative air preheater (as practised in heating of coke ovens), the heat is transferred (A) Through a metallic wall (B) By direct contact of hot flue gas with air (C) By ... material (like chequor bricks) and then heating the air from this hot material (D) None of these

Last Answer : (C) By heating an intermediate material (like chequor bricks) and then heating the air from this hot material

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

Ostwald charts are meant for (A) Computing the excess/deficiency of combustion air (B) Calculation of flue gas temperature (C) Computation of flue gas analysis (D) None of these

Description : Ostwald charts are meant for (A) Computing the excess/deficiency of combustion air (B) Calculation of flue gas temperature (C) Computation of flue gas analysis (D) None of these

Last Answer : (A) Computing the excess/deficiency of combustion air

Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of(A) Furnace oil with air(B) Furnace oil with oxygen(C) Blast furnace gas with air(D) Blast furnace gas with oxygen

Description : Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of (A) Furnace oil with air (B) Furnace oil with oxygen (C) Blast furnace gas with air (D) Blast furnace gas with oxygen

Last Answer : (C) Blast furnace gas with air

In which of the waste heat recovery equipment, the flow of flue gas and air is alternately reversed after a fixed interval of time? (A) Recuperator (B) Regenerator (C) Waste heat boiler (D) None of these

Description : In which of the waste heat recovery equipment, the flow of flue gas and air is alternately reversed after a fixed interval of time? (A) Recuperator (B) Regenerator (C) Waste heat boiler (D) None of these

Last Answer : (B) Regenerator

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Description : To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Ingress of cold air in the furnaces through cracks, charging doors, openings etc(A) Reduces the flue gas temperature and makes the furnace atmosphereoxidising(B) Increases the load on the induced draft fan(C) Reduces the furnace draught(D) All (A), (B) and (C)

Description : Ingress of cold air in the furnaces through cracks, charging doors, openings etc (A) Reduces the flue gas temperature and makes the furnace atmosphere oxidising (B) Increases the load on the induced draft fan (C) Reduces the furnace draught (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Description : Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Last Answer : (A) Reduces its thermal efficiency

In order to maintain an oxidising atmosphere in a furnace, it should have (A) More of excess air (B) Less of excess air (C) More of CO in flue gas (D) More of CO2 in flue gas

Description : In order to maintain an oxidising atmosphere in a furnace, it should have (A) More of excess air (B) Less of excess air (C) More of CO in flue gas (D) More of CO2 in flue gas

Last Answer : (A) More of excess air

Ceramic recuperators compared to metallic recuperators for the same duty (A) Are lighter (B) Occupy more space (C) Are less costly (D) Have higher pressure differential between flue gas & air side

Description : Ceramic recuperators compared to metallic recuperators for the same duty (A) Are lighter (B) Occupy more space (C) Are less costly (D) Have higher pressure differential between flue gas & air side

Last Answer : (B) Occupy more space

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to volatile matter percentage in coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Description : Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to ... coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Last Answer : (D) Calorific value of natural gas is more than that of LPG

Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Description : Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Last Answer : (B) Keeping the flue gas exhaust temperature very high

Presence of nitrogen in combustion air does not reduce the (A) Amount of heat liberated (B) Flame temperature (C) Flue gas temperature (D) Any of the above

Description : Presence of nitrogen in combustion air does not reduce the (A) Amount of heat liberated (B) Flame temperature (C) Flue gas temperature (D) Any of the above

Last Answer : (A) Amount of heat liberated

A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large quantity of hydrogen in the fuel (B) Low calorific value of the fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Description : A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large ... fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Last Answer : (D) Lack of thorough mixing of fuel with air

A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has been used for combustion (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Description : A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has ... (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Last Answer : (C) Complete combustion of fuel has taken place

Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Description : Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Description : Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Last Answer : (C) 20

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion (B) Nitrogen percentage in the fuel is very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Description : Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion ... very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Last Answer : (C) Excess air has been used for combustion

Economizer is provided to utilize the flue gas heat for ___ a) preheating the boiler feed water b) preheating the stock c) preheating the combustion air d) preheating fuel

Description : Economizer is provided to utilize the flue gas heat for ___ a) preheating the boiler feed water b) preheating the stock c) preheating the combustion air d) preheating fuel

Last Answer : preheating the boiler feed water

Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Description : Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Last Answer : (D) It erodes furnace walls

Oxygen trim control strategy __ a. continuously measures the oxygen content in the flue gas b. adjusts the combustion air flow c. Continually tuning the air-fuel mixture. d. All of above

Description : Oxygen trim control strategy __ a. continuously measures the oxygen content in the flue gas b. adjusts the combustion air flow c. Continually tuning the air-fuel mixture. d. All of above

Last Answer : d. All of above

Which of these is an output of a ‘Furnace’? a. Fuel gas b. Cool Air c. Flue gases d. Water Vapor

Description : Which of these is an output of a ‘Furnace’? a. Fuel gas b. Cool Air c. Flue gases d. Water Vapor

Last Answer : c. Flue gases

It is the unbalanced force developed in a turbo jet engine that is caused by the difference in the momentum of the low-velocity air entering the engine and the high velocity exhaust gases leaving the engine.  a. Fall  b. Lift  c. Drag  d. Thrust

Description : It is the unbalanced force developed in a turbo jet engine that is caused by the difference in the momentum of the low-velocity air entering the engine and the high velocity exhaust gases leaving the engine.  a. Fall  b. Lift  c. Drag  d. Thrust

Last Answer : Thrust

A 0.064 kg of octane vapor (MW = 114) is mixed with0.91 kg of air (MW = 29.0) in the manifold of an Engine. The total pressure in the manifold is 86.1 kPa, and a temperature is 290 K. assume octane behaves ideally. What is the partial pressure of the air in the mixture in KPa?  a. 46.8  b. 48.6  c. 84.6  d. 64.8

Description : A 0.064 kg of octane vapor (MW = 114) is mixed with0.91 kg of air (MW = 29.0) in the manifold of an Engine. The total pressure in the manifold is 86.1 kPa, and a temperature is 290 K. assume octane behaves ideally. What is ... of the air in the mixture in KPa?  a. 46.8  b. 48.6  c. 84.6  d. 64.8

Last Answer : 84.6

While swimming at depth of120m in a fresh water lake, A fish emits an air bubbles of volume 2.0mm³ atmospheric pressure is 100kPa. What is the pressure of the bubble?  a) 217.7 kPa  b) 317.7 kPa  c) 417.7 kPa  d) 517.7 kPa Formula: P= δh

Description : While swimming at depth of120m in a fresh water lake, A fish emits an air bubbles of volume 2.0mm³ atmospheric pressure is 100kPa. What is the pressure of the bubble?  a) 217.7 kPa  b) 317.7 kPa  c) 417.7 kPa  d) 517.7 kPa Formula: P= δh

Last Answer : 217.7 kPa