When a ship floats at its designed water line, the vertical distance from water line to the bottom of the ship is known as (A) Beam (B) Depth (C) Freeboard (D) Draft

When a ship floats at its designed water line, the vertical distance from water line to the bottom
of the ship is known as
(A) Beam
(B) Depth
(C) Freeboard
(D) Draft
by

1 Answer

Answer :

(D) Draft
by

Related questions

In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Description : In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Last Answer : (d) Depth of rib

The effective depth of a T-beam is the distance between the (a) Centre of the flange and the top of the tensile reinforcement (b) Top of the flange and the centre of the tensile reinforcement (c) Bottom of the flange and the centre of the tensile reinforcement (d) Centre of the flange and the bottom centre of the tensile reinforcement

Description : The effective depth of a T-beam is the distance between the (a) Centre of the flange and the top of the tensile reinforcement (b) Top of the flange and the centre of the tensile ... centre of the tensile reinforcement (d) Centre of the flange and the bottom centre of the tensile reinforcement

Last Answer : (b) Top of the flange and the centre of the tensile reinforcement

The maximum harbour depth below lowest low water is generally equal to (i) Loaded draft +1.2 m when bottom is rock (ii) Loaded draft +1.8 m when bottom is soft (iii) Loaded draft +1.2 m when bottom is soft (iv) Loaded draft +1.8 m when bottom is rock Of these statements (A) (i) and (ii) are correct (B) (i) and (iii) are correct (C) (ii) and (iv) are correct (D) (iii) and (iv) are correct

Description : The maximum harbour depth below lowest low water is generally equal to (i) Loaded draft +1.2 m when bottom is rock (ii) Loaded draft +1.8 m when bottom is soft (iii) Loaded draft +1.2 m when bottom is ... ) and (iii) are correct (C) (ii) and (iv) are correct (D) (iii) and (iv) are correct

Last Answer : (D) (iii) and (iv) are correct

The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is(A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Description : The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is (A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Last Answer : (D) 8 cm

If a beam fails in bond, then its bond strength can be increased most economically by (A) Increasing the depth of beam (B) Using thinner bars but more in number (C) Using thicker bars but less in number (D) Providing vertical stirrups

Description : If a beam fails in bond, then its bond strength can be increased most economically by (A) Increasing the depth of beam (B) Using thinner bars but more in number (C) Using thicker bars but less in number (D) Providing vertical stirrups

Last Answer : Answer: Option B

For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Description : For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Last Answer : Answer: Option B

A uniform body 3 m long, 2 m wide and 1 m deep floats in water. If the depth of immersion is 0.6 m, then the weight of the body is (A) 3.53 kN (B) 33.3 kN (C) 35.3 kN (D) None of these

Description : A uniform body 3 m long, 2 m wide and 1 m deep floats in water. If the depth of immersion is 0.6 m, then the weight of the body is (A) 3.53 kN (B) 33.3 kN (C) 35.3 kN (D) None of these

Last Answer : Answer: Option C

For wave action in dams, the maximum height of freeboard is generally taken to be equal to (A) 0.5 hw (B) 0.75 hw (C) 1.25 hw (D) 1.50 hw

Description : For wave action in dams, the maximum height of freeboard is generally taken to be equal to (A) 0.5 hw (B) 0.75 hw (C) 1.25 hw (D) 1.50 hw

Last Answer : Answer: Option D

Though the effective depth of a T-beam is the distance between the top compression edge to the centre of the tensile reinforcement, for heavy loads, it is taken as (A) 1/8th of the span (B) 1/10th of the span (C) 1/12th of the span (D) 1/16th of the span

Description : Though the effective depth of a T-beam is the distance between the top compression edge to the centre of the tensile reinforcement, for heavy loads, it is taken as (A) 1/8th of the span (B) 1/10th of the span (C) 1/12th of the span (D) 1/16th of the span

Last Answer : Answer: Option C

If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Last Answer : Answer: Option C

The breadth of the flange of a T-beam is (a) 1/3rd of the effective span of the T-beam (b) Twelve times the depth of slab plus breadth of rib. (c) Centre to centre distance between the adjacent beam. (d) Least of (a) , (b) or (c)

Description : The breadth of the flange of a T-beam is (a) 1/3rd of the effective span of the T-beam (b) Twelve times the depth of slab plus breadth of rib. (c) Centre to centre distance between the adjacent beam. (d) Least of (a) , (b) or (c)

Last Answer : (d) Least of (a) , (b) or (c)

When a ship floats on water (a) It displaces no water (b) The mass of water displaced is more than the mass of the ship (c) The mass of water displaced is equal to the mass of the ship (d) The mass of water displaced is less than the mass of the ship

Description : When a ship floats on water (a) It displaces no water (b) The mass of water displaced is more than the mass of the ship (c) The mass of water displaced is equal to the mass of the ship (d) The mass of water displaced is less than the mass of the ship

Last Answer : Ans:(c)

That an Iron ship floats in water but an Iron ball sinks, is an example of - (1) Newton's second law (2) Pascal's law (3) Archimedes Principle (4) Dalton's law

Description : That an Iron ship floats in water but an Iron ball sinks, is an example of - (1) Newton's second law (2) Pascal's law (3) Archimedes Principle (4) Dalton's law

Last Answer : (3) Archimedes Principle Explanation: The floating of an iron ship in water is an example of Archimedes principle. Archimedes' principle states that an object floats on water if the weight of the water ... . Since the average density of the ship as a whole is less than the density of water.

Does anyone Freeboard?

Description : Does anyone Freeboard?

Last Answer : Have you ever snowboarded before? The site seems to compare riding the board to snowboarding.

The vertical distance between the springing line and highest point of the inner curve of an arch is known as (A) Intrados (B) Rise (C) Spandril (D) Extrados

Description : The vertical distance between the springing line and highest point of the inner curve of an arch is known as (A) Intrados (B) Rise (C) Spandril (D) Extrados

Last Answer : Answer: Option B

The vertical posts placed at the top and bottom ends of a flight supporting the hand rail are known as (A) Balusters (B) Newel posts (C) Balustrades (D) Railings

Description : The vertical posts placed at the top and bottom ends of a flight supporting the hand rail are known as (A) Balusters (B) Newel posts (C) Balustrades (D) Railings

Last Answer : Answer: Option B

The vertical distance between the axis of the beam before and after loading at a point is called as _______ a. Deformation b. Deflection c. Slope d. None of above.

Description : The vertical distance between the axis of the beam before and after loading at a point is called as _______ a. Deformation b. Deflection c. Slope d. None of above.

Last Answer : b. Deflection

In a two lane channel, bottom width of channel is given by (A) Manoeuvring lane + (2 × Bank clearance lane) (B) (2 × Manoeuvring lane) + (2 × Bank clearance lane) (C) (2 × Manoeuvring lane) + (2 × Bank clearance lane + ship clearance lane) (D) Manoeuvring lane + (2 × Bank clearance lane) + ship clearance lane

Description : In a two lane channel, bottom width of channel is given by (A) Manoeuvring lane + (2 Bank clearance lane) (B) (2 Manoeuvring lane) + (2 Bank clearance lane) (C) (2 ... clearance lane + ship clearance lane) (D) Manoeuvring lane + (2 Bank clearance lane) + ship clearance lane

Last Answer : (C) (2 × Manoeuvring lane) + (2 × Bank clearance lane + ship clearance lane)

The depth of an arch is the distance between (A) Ground level and springing line (B) Crown and springing line (C) Crown and ground level (D) Intrados and extrados

Description : The depth of an arch is the distance between (A) Ground level and springing line (B) Crown and springing line (C) Crown and ground level (D) Intrados and extrados

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water (F.S.D.) (B) Area of canal in cutting = BD + Sd 2 where B = bed width, d = depth of cutting and S is the side slope (C) If F.S.L. is above N.S.L the canal is called partly in cutting and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Description : Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water ... and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Last Answer : (D) All the above

The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3

Description : The ratio of the length and depth of a simply supported rectangular beam which experiences  maximum bending stress equal to tensile stress, due to same load at its mid span, is  (A) 1/2  (B) 2/3  (C) 1/4  (D) 1/3

Last Answer : (B) 2/3 

If the depth of a simply supported beam carrying an isolated load at its centre, is doubled, the deflection of the beam at the centre will be changed by a factor of (A) 2 (B) 1/2 (C) 8 (D) 1/8

Description : If the depth of a simply supported beam carrying an isolated load at its centre, is doubled, the deflection of the beam at the centre will be changed by a factor of (A) 2 (B) 1/2 (C) 8 (D) 1/8

Last Answer : (D) 1/8

The deflection of any rectangular beam simply supported, is (A) Directly proportional to its weight (B) Inversely proportional to its width (C) Inversely proportional to the cube of its depth (D) Directly proportional to the cube of its length

Description : The deflection of any rectangular beam simply supported, is (A) Directly proportional to its weight (B) Inversely proportional to its width (C) Inversely proportional to the cube of its depth (D) Directly proportional to the cube of its length

Last Answer : (C) Inversely proportional to the cube of its depth

A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 , the area of steel required, is (A) 14 cm(B) 15 cm2(C) 16 cm2(D) 17 cm

Description : A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 ... area of steel required, is (A) 14 cm (B) 15 cm2 (C) 16 cm2 (D) 17 cm

Last Answer : Answer: Option C

In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis

Description : In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis

Last Answer : Answer: Option B

An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity of shear stress, is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Last Answer : Answer: Option A

If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less than the depth of critical neutral axis, the steel in the tensile zone attains its maximum stress earlier (C) Is equal to the depth of critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Description : If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less ... critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Last Answer : Answer: Option D

The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed (A) 10 (B) 15 (C) 20 (D) 25

Description : For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : Answer: Option C

During percussion drilling (A) Ground water observations are hindered due to entry of the slurry in the soil below the bottom of the hole (B) Caving or mixing of strata are caused in soft soils or cohesionless soils (C) The soil to a considerable depth below the bottom of the hole gets disturbed (D) All the above

Description : During percussion drilling (A) Ground water observations are hindered due to entry of the slurry in the soil below the bottom of the hole (B) Caving or mixing of strata are caused in soft soils or ... The soil to a considerable depth below the bottom of the hole gets disturbed (D) All the above

Last Answer : Answer: Option D

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°

Description : An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°

Last Answer : Answer: Option C

If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Description : If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Last Answer : Answer: Option B

A beam curved in plan is designed for (A) Bending moment and shear (B) Bending moment and torsion (C) Shear and torsion (D) Bending moment, shear and torsion

Description : A beam curved in plan is designed for (A) Bending moment and shear (B) Bending moment and torsion (C) Shear and torsion (D) Bending moment, shear and torsion

Last Answer : Answer: Option D

Depth of lean concrete bed placed at the bottom of a wall footing, is kept (A) 10 cm (B) 15 cm (C) Equal to its projection beyond wall base (D) Less than its projection beyond wall base

Description : Depth of lean concrete bed placed at the bottom of a wall footing, is kept (A) 10 cm (B) 15 cm (C) Equal to its projection beyond wall base (D) Less than its projection beyond wall base

Last Answer : Answer: Option C

Pick up the incorrect statement from the following: (A) The rate of flow of water through a unit cross-sectional area under a unit hydraulic gradient, is called coefficient of permeability (B) The rate of flow of water through a vertical strip of the aquifer of unit width and full depth under a unit hydraulic gradient, is called coefficient of transmissibility (C) The flow of water through aquifers, is governed by the Darcy's law (D) The term 'transmissibility' was introduced by Meinzer

Description : Pick up the incorrect statement from the following: (A) The rate of flow of water through a unit cross-sectional area under a unit hydraulic gradient, is called coefficient of permeability (B) ... aquifers, is governed by the Darcy's law (D) The term 'transmissibility' was introduced by Meinzer

Last Answer : Answer: Option D

The depth of the centre of pressure on a vertical rectangular gate 8 m wide and 6 m high, when the water surface coincides with the top of the gate, is (A) 2.4 m (B) 3.0 m (C) 4.0 m (D) 5.0 m

Description : The depth of the centre of pressure on a vertical rectangular gate 8 m wide and 6 m high, when the water surface coincides with the top of the gate, is (A) 2.4 m (B) 3.0 m (C) 4.0 m (D) 5.0 m

Last Answer : Answer: Option B

If d is the economic designed depth of a slab, the thickness of the cement concrete pavement slab at interior, is kept (A) 1.275 d (B) 1.125 d (C) 0.85 d (D) 0.75 d

Description : If d is the economic designed depth of a slab, the thickness of the cement concrete pavement slab at interior, is kept (A) 1.275 d (B) 1.125 d (C) 0.85 d (D) 0.75 d

Last Answer : Answer: Option C

Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to resist a sagging bending moment near mid-span. (c) When the slab is built into a brick or masonry wall the slab should be designed to resist a hogging moment at the face of the support. (d) All of the above.

Description : Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to ... be designed to resist a hogging moment at the face of the support. (d) All of the above.

Last Answer : (d) All of the above.

A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one-third of the diagonal tension and ignoring the weight of the beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Last Answer : Answer: Option C

The intensity of vertical pressure at a depth directly below the point load on its axis of loading is: (A) 0.4775 Q/Z (B) 0.4775 Q/Z² (C) 0.4775 Q/Z3 (D) 0.4775 Q Z

Description : The intensity of vertical pressure at a depth directly below the point load on its axis of loading is: (A) 0.4775 Q/Z (B) 0.4775 Q/Z² (C) 0.4775 Q/Z3 (D) 0.4775 Q Z

Last Answer : (B) 0.4775 Q/Z²

Pick out the wrong statement. (A) With decrease in feed temperature, the number of plates required for binary distillation decreases for a given ‘L/V’ ratio (B) The extraction per unit of total height for a short packed column is more effective than for a tall column, in case of liquid-liquid extraction(C) Natural draft cooling towers are made of ferroconcrete and its cross￾section is wider at the bottom(D) Vander wall adsorption is also called chemisorption

Description : Pick out the wrong statement. (A) With decrease in feed temperature, the number of plates required for binary distillation decreases for a given L/V' ratio (B) The extraction per unit ... and its cross￾section is wider at the bottom (D) Vander wall adsorption is also called chemisorption

Last Answer : (D) Vander wall adsorption is also called chemisorption

A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. Which of the following statement is correct? (A) The pressure on the wall at the liquid level is minimum(B) The pressure on the bottom of the wall is maximum (C) The pressure on the wall at the liquid level is zero, and on the bottom of the wall is maximum (D) The pressure on the bottom of the wall is zero

Description : A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. Which of the following statement is correct? (A) The pressure on the wall at the liquid level is maximum (B) ... and on the bottom of the wall is maximum (D) The pressure on the bottom of the wall is zero

Last Answer : Answer: Option C

In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed as a cantilever The correct answer is (A) (i) and (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Description : In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed ... (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Last Answer : Answer: Option A

At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of the section by (A) Depth of the section (B) Depth of the neutral axis (C) Maximum tensile stress at the section (D) Maximum compressive stress at the section

Description : At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of  the section by  (A) Depth of the section  (B) Depth of the neutral axis  (C) Maximum tensile stress at the section  (D) Maximum compressive stress at the section

Last Answer : (B) Depth of the neutral axis 

For a strongest rectangular beam cut from a circular log, the ratio of the width and depth, is (A) 0.303 (B) 0.404 (C) 0.505 (D) 0.707

Description : For a strongest rectangular beam cut from a circular log, the ratio of the width and depth, is  (A) 0.303  (B) 0.404  (C) 0.505  (D) 0.707 

Last Answer : (D) 0.707 

The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd

Description : The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd

Last Answer : (B) 3WL/2fd²

A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Description : A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Last Answer : (C) 25 cm

If the width b and depth d of a beam simply supported with a central load are interchanged, the deflection at the centre of the beam will be changed in the ratio of (A) b/d (B) d/b (C) (d/b)2 (D) (b/d)

Description : If the width b and depth d of a beam simply supported with a central load are interchanged, the  deflection at the centre of the beam will be changed in the ratio of  (A) b/d (B) d/b (C) (d/b)2 (D) (b/d)

Last Answer : (D) (b/d)2

The width b and depth d of a beam cut from a wooden cylindrical log of 100 cm diameter for maximum strength are: (A) b = 57.73 cm d = 81.65 cm (B) b = 81.65 cm d = 57.73 cm (C) b = 50.00 cm d = 50.00 cm (D) b = 40.00 cm d = 80.00 cm

Description : The width b and depth d of a beam cut from a wooden cylindrical log of 100 cm diameter for  maximum strength are:  (A) b = 57.73 cm d = 81.65 cm  (B) b = 81.65 cm d = 57.73 cm  (C) b = 50.00 cm d = 50.00 cm  (D) b = 40.00 cm d = 80.00 cm 

Last Answer : (A) b = 57.73 cm d = 81.65 cm