The vertical posts placed at the top and bottom ends of a flight supporting the hand rail are known as (A) Balusters (B) Newel posts (C) Balustrades (D) Railings

The vertical posts placed at the top and bottom ends of a flight supporting the hand rail are known
as
(A) Balusters
(B) Newel posts
(C) Balustrades
(D) Railings
by

1 Answer

Answer :

Answer: Option B
by

Related questions

The vertical members fixed between steps and hand rail, are known (A) Balusters (B) Strings (C) Newel posts (D) Soffits

Description : The vertical members fixed between steps and hand rail, are known (A) Balusters (B) Strings (C) Newel posts (D) Soffits

Last Answer : Answer: Option A

Define the terms Newel post and Headroom in vertical communication.

Description : Define the terms Newel post and Headroom in vertical communication.

Last Answer : Newel post : This is the vertical member which is placed at the ends of flights to connect the end of strings and hand rail.  Headroom : The vertical distance between the nosing of one flight and bottom of flight immediately above is known as the headroom.

The vertical clearance of bottom most foot over bridge structure above rail level is a) 6525 mm* b) 3660 mm c) 5330 mm d) 6250 mm

Description : The vertical clearance of bottom most foot over bridge structure above rail level is a) 6525 mm* b) 3660 mm c) 5330 mm d) 6250 mm

Last Answer : a) 6525 mm*

Vertical Clearance (VC) in water way bridges is the level difference between a) HFL and Formation level b) Bed level and bottom of superstructure c) HFL and bottom of superstructure* d) Rail level and Formation level

Description : Vertical Clearance (VC) in water way bridges is the level difference between a) HFL and Formation level b) Bed level and bottom of superstructure c) HFL and bottom of superstructure* d) Rail level and Formation level

Last Answer : c) HFL and bottom of superstructure*

The additional piles which are driven to increase the capacity of supporting loads on vertical piles, are known (A) Construction piles (B) Raking piles (C) Eccentric piles (D) Sinking piles

Description : The additional piles which are driven to increase the capacity of supporting loads on vertical piles, are known (A) Construction piles (B) Raking piles (C) Eccentric piles (D) Sinking piles

Last Answer : Answer: Option B

In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Description : In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Last Answer : (i) +0.5mm, -0 mm in vertical *

Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The internal surface of the mould is kept clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Description : Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The ... clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Last Answer : Answer: Option D

For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Last Answer : Answer: Option D

A very comfortable type of stairs is (A) Straight (B) Dog legged (C) Geometrical (D) Open newel

Description : A very comfortable type of stairs is (A) Straight (B) Dog legged (C) Geometrical (D) Open newel

Last Answer : Answer: Option D

Pick up the incorrect statement from the following: (A) In dog-legged stairs, no space between its flights is provided (B) In open newel stair, a rectangular well is provided (C) In geometric stair, a curved shaped well between forward and backward flights, is provided (D) In geometrical stair, two quarter space landing is provided

Description : Pick up the incorrect statement from the following: (A) In dog-legged stairs, no space between its flights is provided (B) In open newel stair, a rectangular well is provided (C) In ... forward and backward flights, is provided (D) In geometrical stair, two quarter space landing is provided

Last Answer : Answer: Option D

A piece of metal of specific gravity 13.6 is placed in mercury of specific gravity 13.6, what fraction of it volume is under mercury? (A) The metal piece will simply float over the mercury (B) The metal piece will be immersed in mercury by half (C) Whole of the metal piece will be immersed with its top surface just at mercury level (D) Metal piece will sink to the bottom

Description : A piece of metal of specific gravity 13.6 is placed in mercury of specific gravity 13.6, what fraction of it volume is under mercury? (A) The metal piece will simply float over the mercury (B ... will be immersed with its top surface just at mercury level (D) Metal piece will sink to the bottom

Last Answer : Answer: Option C

A reinforced concrete cantilever porch has thickness t. The main reinforcing steel will be placed (a) At mid-thickness (b) At t/3 from the top (c) Close to the bottom surface (d) Close to the top surface

Description : A reinforced concrete cantilever porch has thickness t. The main reinforcing steel will be placed (a) At mid-thickness (b) At t/3 from the top (c) Close to the bottom surface (d) Close to the top surface

Last Answer : (d) Close to the top surface

Marking on weld should be done (i) On centre of the rail head (ii) 10 mm below the top surface of rail head.* (iii) 10 mm above the bottom surface of rail head. (iv) None of the above

Description : Marking on weld should be done (i) On centre of the rail head (ii) 10 mm below the top surface of rail head.* (iii) 10 mm above the bottom surface of rail head. (iv) None of the above

Last Answer : ii) 10 mm below the top surface of rail head.*

Flood level gauge to be marked a) commencing from bed level to top b) commencing from bottom of girder towards bed level* c) commencing from Rail level d) commencing from Danger level

Description : Flood level gauge to be marked a) commencing from bed level to top b) commencing from bottom of girder towards bed level* c) commencing from Rail level d) commencing from Danger level

Last Answer : b) commencing from bottom of girder towards bed level*

In shallow type girders, the rail level shall be a) 25mm above the top flange of girder* b) near the bottom of the girder c) near the middle of the girder d) below the girder

Description : In shallow type girders, the rail level shall be a) 25mm above the top flange of girder* b) near the bottom of the girder c) near the middle of the girder d) below the girder

Last Answer : a) 25mm above the top flange of girder*

Enlarged head of a supporting column of a flat slab is technically known as (A) Supporting end of the column (B) Top of the column (C) Capital (D) Drop panel

Description : Enlarged head of a supporting column of a flat slab is technically known as (A) Supporting end of the column (B) Top of the column (C) Capital (D) Drop panel

Last Answer : Answer: Option C

Pick up the incorrect statement from the following: (A) In king post truss, one vertical post is used (B) In a queen post truss, one vertical post is used (C) In a queen post truss, two vertical posts are used (D) None of thes

Description : Pick up the incorrect statement from the following: (A) In king post truss, one vertical post is used (B) In a queen post truss, one vertical post is used (C) In a queen post truss, two vertical posts are used (D) None of thes

Last Answer : Answer: Option B

The vertical faces of a door opening which support frame of the door, are (A) Jambs (B) Posts (C) Reveals (D) Styles

Description : The vertical faces of a door opening which support frame of the door, are (A) Jambs (B) Posts (C) Reveals (D) Styles

Last Answer : Answer: Option A

When a ship floats at its designed water line, the vertical distance from water line to the bottom of the ship is known as (A) Beam (B) Depth (C) Freeboard (D) Draft

Description : When a ship floats at its designed water line, the vertical distance from water line to the bottom of the ship is known as (A) Beam (B) Depth (C) Freeboard (D) Draft

Last Answer : (D) Draft

Can anyone give me a Scientific explanation for the way snow neatly accumulates on railings ?

Description : Can anyone give me a Scientific explanation for the way snow neatly accumulates on railings ?

Last Answer : Well, gravity makes it fall from the sky. It collects as long as it can hang together, but there comes a point at which it falls off the sides.

Is galvanizing or painting railings more appropriate?

Description : The old stairs in the cottage are no longer hoods. I want to have a new metal railing welded into which the wooden stairs will be mounted. Is it better to paint the railing or have it galvanized? Galvanizing is probably very expensive, huh? My point is to keep the railing from rusting.

Last Answer : If you have the opportunity, definitely have the construction hot-dip galvanized - although it is "somewhat more expensive", but it is enough "once in a lifetime" (so no more costs, no work ... , they have to drill "cavities" so that the structure does not tear due to temperature difference.

How can you prevent railings from rusting?

Description : How can you prevent railings from rusting?

Last Answer : Need answer

How to Build Deck Railings

Description : How to Build Deck Railings

Last Answer : How to Build Deck Railings Deck railings, or better known as railings, alone are essential for both the aesthetic appearance and the safety of the deck. Beauty and Strength', both are the ... the above procedure to create deck railings, you should meet completion within a variable amount of time.

A ball is thrown horizontally from the top of a cliff. Assuming no air resistance, the acceleration of the ball while it is in flight is: w) in the vertical direction only x) in the horizontal direction only y) in the vertical and horizontal directions z) zero.

Description : A ball is thrown horizontally from the top of a cliff. Assuming no air resistance, the acceleration of the ball while it is in flight is: w) in the vertical direction only x) in the horizontal direction only y) in the vertical and horizontal directions z) zero.

Last Answer : ANSWER: W -- IN THE VERTICAL DIRECTION ONLY

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

In a perfect prismatic compass (A) Magnetic axis and geometric axis of the needle coincide (B) Ends of the needle and pivot are in same vertical and horizontal planes (C) Pivot is vertically over the centre of the graduated circle (D) All the above

Description : In a perfect prismatic compass (A) Magnetic axis and geometric axis of the needle coincide (B) Ends of the needle and pivot are in same vertical and horizontal planes (C) Pivot is vertically over the centre of the graduated circle (D) All the above

Last Answer : (D) All the above

For a beam having fixed ends, the unknown element of the reactions, is (A) Horizontal components at either end (B) Vertical components at either end (C) Horizontal component at one end and vertical component at the other (D) Horizontal and vertical components at both the ends

Description : For a beam having fixed ends, the unknown element of the reactions, is  (A) Horizontal components at either end  (B) Vertical components at either end  (C) Horizontal component at one end and vertical component at the other  (D) Horizontal and vertical components at both the ends 

Last Answer : (D) Horizontal and vertical components at both the ends 

The centre to centre spacing of vertical stirrups, in a rectangular beam, is (a) Increased towards the centre of the span of the beam (b) Decreased towards the centre of the span of the beam. (c) Increased at the ends. (d) None of these

Description : The centre to centre spacing of vertical stirrups, in a rectangular beam, is (a) Increased towards the centre of the span of the beam (b) Decreased towards the centre of the span of the beam. (c) Increased at the ends. (d) None of these

Last Answer : (a) Increased towards the centre of the span of the beam

Why supporting wall of a dam is built very broad at the bottom?

Description : Why supporting wall of a dam is built very broad at the bottom?

Last Answer : The supporting wall of a dam is built very broad at the bottom because at bottom the water pressure is very large as compared to the surface of water.

When H is the flight height, R is the appropriate radial measure and d is the relief displacement, the vertical height of an object appearing on an aerial photograph is

Description : When H is the flight height, R is the appropriate radial measure and d is the relief displacement, the vertical height of an object appearing on an aerial photograph is

Last Answer : dH/R

If a ‘vertical aerial photograph’, (20 cm x 20 cm) in size, on a R.F.I: 10,000, has 60% longitudinal overlap and 40% side overlap, the actual ground length covered by each photograph in the longitudinal direction of the flight will be : (a) 4 km (b) 6 km (c) 0.8 km (d) 0.4 km

Description : If a ‘vertical aerial photograph’, (20 cm x 20 cm) in size, on a R.F.I: 10,000, has 60% longitudinal overlap and 40% side overlap, the actual ground length covered by each photograph in the longitudinal direction of the flight will be : (a) 4 km (b) 6 km (c) 0.8 km (d) 0.4 km

Last Answer : .8

The specific humidity scale on a psychrometric chart is along the: a. Bottom horizontal axis b. Right side vertical axis c. Top horizontal axis at the top of the chart d. Left saturation line e. Left-side vertical axis and left side

Description : The specific humidity scale on a psychrometric chart is along the: a. Bottom horizontal axis b. Right side vertical axis c. Top horizontal axis at the top of the chart d. Left saturation line e. Left-side vertical axis and left side

Last Answer : Answer: B

The dry-bulb temperature scale is read on a psychrometric chart along the: a. Left vertical axis b. Right vertical axis c. Saturation line and sloping downward to the right d. Top horizontal axis e. Horizontal axis on the bottom of the chart

Description : The dry-bulb temperature scale is read on a psychrometric chart along the: a. Left vertical axis b. Right vertical axis c. Saturation line and sloping downward to the right d. Top horizontal axis e. Horizontal axis on the bottom of the chart

Last Answer : ANSWER : E

The film thickness for laminar film condensation on vertical surface __________ from top to bottom. (A) Cumulatively increases (B) Cumulatively decreases (C) Remain constant (D) And the surface conductance increase

Description : The film thickness for laminar film condensation on vertical surface __________ from top to bottom. (A) Cumulatively increases (B) Cumulatively decreases (C) Remain constant (D) And the surface conductance increase

Last Answer : (A) Cumulatively increases

What feature adjusts the top and bottom margins so that the text is centered vertically on the printed page? a) Vertical justifying b) Vertical adjusting c) Dual centering d) Horizontal centering e) None of these

Description : What feature adjusts the top and bottom margins so that the text is centered vertically on the printed page? a) Vertical justifying b) Vertical adjusting c) Dual centering d) Horizontal centering e) None of these

Last Answer : a) Vertical justifying

According to RBI Guidelines on Sale of Stressed Assets by Banks, identification of stressed assets beyond a specified value, as may be determined by bank’s policy, for sale is ___________. a) Top-down b) Bottom–top c) Horizontal d) Vertical

Description : According to RBI Guidelines on Sale of Stressed Assets by Banks, identification of stressed assets beyond a specified value, as may be determined by bank’s policy, for sale is ___________. a) Top-down b) Bottom–top c) Horizontal d) Vertical

Last Answer : a) Top-down

Colour of rail ends becomes after preheating ? (i) Golden * (ii) Pink Red (iii) Red (iv) Yellow

Description : Colour of rail ends becomes after preheating ? (i) Golden * (ii) Pink Red (iii) Red (iv) Yellow

Last Answer : (i) Golden

To take care of differential cooling rail ends of 72 UTS rails are lifted by? (i) 1 to 1.5 mm (ii) 1 to 2 mm (iii) 2 to 2.5 mm (iv) 3 to 4 mm *

Description : To take care of differential cooling rail ends of 72 UTS rails are lifted by? (i) 1 to 1.5 mm (ii) 1 to 2 mm (iii) 2 to 2.5 mm (iv) 3 to 4 mm *

Last Answer : iv) 3 to 4 mm *

To take care of differential cooling rail ends of 90 UTS rails are lifted by? (i) 1 mm (ii) 2 mm (iii) 2 to 2.2 mm.* (iv) 1 to 2 mm

Description : To take care of differential cooling rail ends of 90 UTS rails are lifted by? (i) 1 mm (ii) 2 mm (iii) 2 to 2.2 mm.* (iv) 1 to 2 mm

Last Answer : (iii) 2 to 2.2 mm.*

What is Pre Heating Temperature of rail ends in AT Welding? (i) 300 ± 20oC (ii) 400 ± 20oC (iii) 500 ± 20oC (iv) 600 ± 20oC *

Description : What is Pre Heating Temperature of rail ends in AT Welding? (i) 300 ± 20oC (ii) 400 ± 20oC (iii) 500 ± 20oC (iv) 600 ± 20oC *

Last Answer : (iv) 600 ± 20oC *

How much rail ends are cleaned with Kerosene Oil and steel wire brush? (i) Minimum 100 mm both side (ii) Minimum 50 mm both side.* (iii) No need (iv) As decided by site supervisor

Description : How much rail ends are cleaned with Kerosene Oil and steel wire brush? (i) Minimum 100 mm both side (ii) Minimum 50 mm both side.* (iii) No need (iv) As decided by site supervisor

Last Answer : (ii) Minimum 50 mm both side.*

On Broad Gauge tracks Banner flag at a level crossing shall be provided at a distance of--- ---------- from ends of check rail before opening the gate for road traffic. a) 5 meters* b) 3 meters c) 6 meters d) 30 meters

Description : On Broad Gauge tracks Banner flag at a level crossing shall be provided at a distance of--- ---------- from ends of check rail before opening the gate for road traffic. a) 5 meters* b) 3 meters c) 6 meters d) 30 meters

Last Answer : a) 5 meters*

Depth of lean concrete bed placed at the bottom of a wall footing, is kept (A) 10 cm (B) 15 cm (C) Equal to its projection beyond wall base (D) Less than its projection beyond wall base

Description : Depth of lean concrete bed placed at the bottom of a wall footing, is kept (A) 10 cm (B) 15 cm (C) Equal to its projection beyond wall base (D) Less than its projection beyond wall base

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) In stone arches, the stones are placed with their natural beds radial (B) In cornices, the stones are placed with their natural beds as vertical (C) In stone walls, the stones are placed with their natural beds as horizontal (D) All the above

Description : Pick up the correct statement from the following: (A) In stone arches, the stones are placed with their natural beds radial (B) In cornices, the stones are placed with their natural beds as vertical (C) In stone walls, the stones are placed with their natural beds as horizontal (D) All the above

Last Answer : Answer: Option D

A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. Which of the following statement is correct? (A) The pressure on the wall at the liquid level is minimum(B) The pressure on the bottom of the wall is maximum (C) The pressure on the wall at the liquid level is zero, and on the bottom of the wall is maximum (D) The pressure on the bottom of the wall is zero

Description : A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. Which of the following statement is correct? (A) The pressure on the wall at the liquid level is maximum (B) ... and on the bottom of the wall is maximum (D) The pressure on the bottom of the wall is zero

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) Inclined borings are made for taking samples under existing structures (B) Inclined borings are occasionally used instead of vertical holes (C) The spacing of inclined borings is kept such that one bore hole is vertically above the bottom of an adjacent bore hole (D) All the above

Description : Pick up the correct statement from the following: (A) Inclined borings are made for taking samples under existing structures (B) Inclined borings are occasionally used instead of vertical holes (C) The ... bore hole is vertically above the bottom of an adjacent bore hole (D) All the above

Last Answer : Answer: Option D

In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Description : In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Last Answer : (d) Depth of rib

A covering of concrete placed on the exposed top of an external wall, is known as (A) Cornice (B) Coping (C) Frieze (D) Linte

Description : A covering of concrete placed on the exposed top of an external wall, is known as (A) Cornice (B) Coping (C) Frieze (D) Linte

Last Answer : Answer: Option B

Minimum depth of ballast cushion below the bottom of sleeper at the rail seat on BG group A route should be :- (a) 350 mm. (b) 250 mm. (c) 300 mm.* (d) 325 mm.

Description : Minimum depth of ballast cushion below the bottom of sleeper at the rail seat on BG group A route should be :- (a) 350 mm. (b) 250 mm. (c) 300 mm.* (d) 325 mm.

Last Answer : (c) 300 mm.*