In case of a hair pin bend of a highway, (A) Minimum radius of inner curve is 14 m (B) Minimum radius of transition is 15 m (C) Circular compound curve may be provided (D) All the above

In case of a hair pin bend of a highway,
(A) Minimum radius of inner curve is 14 m
(B) Minimum radius of transition is 15 m
(C) Circular compound curve may be provided
(D) All the above
by

1 Answer

Answer :

Answer: Option D
by

Related questions

The radius of curvature provided along a transition curve, is (A) Minimum at the beginning (B) Same throughout its length (C) Equal to the radius of circular curve (D) Varying from infinity to the radius of circular curve

Description : The radius of curvature provided along a transition curve, is (A) Minimum at the beginning (B) Same throughout its length (C) Equal to the radius of circular curve (D) Varying from infinity to the radius of circular curve

Last Answer : Answer: Option D

If the length of a transition curve to be introduced between a straight and a circular curve of radius 500 m is 90 m, the maximum perpendicular offset for the transition curve, is (A) 0.70 m (B) 1.70 m (C) 2.70 m (D) 3.70 m

Description : If the length of a transition curve to be introduced between a straight and a circular curve of  radius 500 m is 90 m, the maximum perpendicular offset for the transition curve, is  (A) 0.70 m  (B) 1.70 m  (C) 2.70 m  (D) 3.70 m

Last Answer : (C) 2.70 m 

If the length of a transition curve to be introduced between a straight and a circular curve of radius 500 m is 90 m, the maximum deflection angle to locate its junction point, is (A) 1°43' 08" (B) 1°43' 18" (C) 1°43' 28" (D) 1°43' 38"

Description : If the length of a transition curve to be introduced between a straight and a circular curve of radius 500 m is 90 m, the maximum deflection angle to locate its junction point, is (A) 1°43' 08" (B) 1°43' 18" (C) 1°43' 28" (D) 1°43' 38"

Last Answer : (C) 1°43' 28"

If the designed speed on a circular curve of radius 1400 m is 80 km/hour, no super-elevation is provided, if the camber, is (A) 4 % (B) 3 % (C) 2 % (D) 1.7 %

Description : If the designed speed on a circular curve of radius 1400 m is 80 km/hour, no super-elevation is provided, if the camber, is (A) 4 % (B) 3 % (C) 2 % (D) 1.7 %

Last Answer : Answer: Option C

If the ruling gradient on any highway is 3%, the gradient provided on the curve of 300 metre radius, is (A) 2.00 % (B) 2.25 % (C) 2.50 % (D) 2.75 %

Description : If the ruling gradient on any highway is 3%, the gradient provided on the curve of 300 metre radius, is (A) 2.00 % (B) 2.25 % (C) 2.50 % (D) 2.75 %

Last Answer : Answer: Option D

If the rate of change of the super-elevation along a curved portion of a 7 metre wide road is 1 in 150 and the maximum super-elevation allowed is 1 in 15, the maximum length of the transition curve to be provided at either end, is (A) 65 m (B) 70 m (C) 75 m (D) 80 m

Description : If the rate of change of the super-elevation along a curved portion of a 7 metre wide road is 1 in 150 and the maximum super-elevation allowed is 1 in 15, the maximum length of the transition curve to be provided at either end, is (A) 65 m (B) 70 m (C) 75 m (D) 80 m

Last Answer : Answer: Option B

Full amount of extra width of a pavement on the curve, is provided at (A) Beginning of the transition curve (B) Centre of the transition curve (C) Beginning of the circular curve (D) Centre of the circular curve

Description : Full amount of extra width of a pavement on the curve, is provided at (A) Beginning of the transition curve (B) Centre of the transition curve (C) Beginning of the circular curve (D) Centre of the circular curve

Last Answer : Answer: Option C

Minimum radius of a simple circular curve deflecting through 5°, is (A) 1618.9 m (B) 1816.9 m (C) 1718.9 m (D) 1817.9 m

Description : Minimum radius of a simple circular curve deflecting through 5°, is (A) 1618.9 m (B) 1816.9 m (C) 1718.9 m (D) 1817.9 m

Last Answer : Answer: Option C

In a right angle bend of a road provided with a transition throughout, the maximum polar angle will be (A) 10° (B) 15° (C) 20° (D) 30°

Description : In a right angle bend of a road provided with a transition throughout, the maximum polar angle will be (A) 10° (B) 15° (C) 20° (D) 30°

Last Answer : Answer: Option B

If the rate of gain of radial acceleration is 0.3 m per sec3 and full centrifugal ratio is developed. On the curve the ratio of the length of the transition curve of same radius on road and railway, is (A) 2.828 (B) 3.828 (C) 1.828 (D) 0.828

Description : If the rate of gain of radial acceleration is 0.3 m per sec3 and full centrifugal ratio is developed. On the curve the ratio of the length of the transition curve of same radius on road and railway, is (A) 2.828 (B) 3.828 (C) 1.828 (D) 0.828

Last Answer : (A) 2.828

If the radius of a main curve is 300 m and length of the transition curve is 100 m, the angle with tangent to locate the junction point, is (A) 1° 11' (B) 2° 11' (C) 3° 11' (D) 4° 11'

Description : If the radius of a main curve is 300 m and length of the transition curve is 100 m, the angle with tangent to locate the junction point, is (A) 1° 11' (B) 2° 11' (C) 3° 11' (D) 4° 11'

Last Answer : Answer: Option C

The minimum ratio of the radii of two circular curves of a compound curve, is kept (A) 1.25 (B) 1.5 (C) 1.75 (D) 2.0

Description : The minimum ratio of the radii of two circular curves of a compound curve, is kept (A) 1.25 (B) 1.5 (C) 1.75 (D) 2.0

Last Answer : Answer: Option B

The radius of a simple circular curve is 300 m and length of its specified chord is 30 m. The degree of the curve is (A) 5.73° (B) 5.37° (C) 3.57° (D) 3.75°

Description : The radius of a simple circular curve is 300 m and length of its specified chord is 30 m. The degree of the curve is (A) 5.73° (B) 5.37° (C) 3.57° (D) 3.75°

Last Answer : (A) 5.73°

If the coefficient of friction on the road surface is 0.15 and a maximum super-elevation 1 in 15 is provided, the maximum speed of the vehicles on a curve of 100 metre radius, is (A) 32.44 km/hour (B) 42.44 kg/hour (C) 52.44 km/hour (D) 62.44 km/hour

Description : If the coefficient of friction on the road surface is 0.15 and a maximum super-elevation 1 in 15 is provided, the maximum speed of the vehicles on a curve of 100 metre radius, is (A) 32.44 km/hour (B) 42.44 kg/hour (C) 52.44 km/hour (D) 62.44 km/hour

Last Answer : Answer: Option C

Perpendicular offset from a tangent to the junction of a transition curve and circular curve is equal to (A) Shift (B) Twice the shift (C) Thrice the shift (D) Four times the shift

Description : Perpendicular offset from a tangent to the junction of a transition curve and circular curve is equal to (A) Shift (B) Twice the shift (C) Thrice the shift (D) Four times the shift

Last Answer : (D) Four times the shift

Transition curves are introduced at either end of a circular curve, to obtain (A) Gradually decrease of curvature from zero at the tangent point to the specified quantity at the junction of the transition curve with main curve (B) Gradual increase of super-elevation from zero at the tangent point to the specified amount at the junction of the transition curve with main curve (C) Gradual change of gradient from zero at the tangent point to the specified amount at the junction of the transition curve with main curve (D) None of these

Description : Transition curves are introduced at either end of a circular curve, to obtain (A) Gradually decrease of curvature from zero at the tangent point to the specified quantity at the junction of the ... specified amount at the junction of the transition curve with main curve (D) None of these

Last Answer : (B) Gradual increase of super-elevation from zero at the tangent point to the specified amount at the junction of the transition curve with main curve

When an up gradient of a highway meets a downgrade, the vertical curve provided, is known as (A) Valley curve (B) Sag curve (C) Summit curve (D) All the above

Description : When an up gradient of a highway meets a downgrade, the vertical curve provided, is known as (A) Valley curve (B) Sag curve (C) Summit curve (D) All the above

Last Answer : Answer: Option C

If R is the radius of a main curve and L is the length of the transition curve, the shift of the curve, is (A) L/24 R (B) L2 /24 R (C) L3 /24 R (D) L4 /24 R

Description : If R is the radius of a main curve and L is the length of the transition curve, the shift of the curve, is (A) L/24 R (B) L2 /24 R (C) L3 /24 R (D) L4 /24 R

Last Answer : Answer: Option B

In an ideal transition curve, the radius of curvature (A) Is constant (B) At any point is directly proportional to its distance from the point of commencement (C) Is inversely proportional to the radius of main curve (D) Is directly proportional to the radius of main curve

Description : In an ideal transition curve, the radius of curvature (A) Is constant (B) At any point is directly proportional to its distance from the point of commencement (C) Is inversely proportional to the radius of main curve (D) Is directly proportional to the radius of main curve

Last Answer : Answer: Option C

The type of transition curves generally provided on hill roads, is (A) Circular (B) Cubic parabola (C) Lemniscate (D) Spiral

Description : The type of transition curves generally provided on hill roads, is (A) Circular (B) Cubic parabola (C) Lemniscate (D) Spiral

Last Answer : Answer: Option D

When a number of hair pin bends are introduced, a minimum intervening distance in between is kept (A) 20 m (B) 40 m (C) 60 m (D) 100 m

Description : When a number of hair pin bends are introduced, a minimum intervening distance in between is kept (A) 20 m (B) 40 m (C) 60 m (D) 100 m

Last Answer : Answer: Option C

The standard equation of a cubic parabolic transition curve provided on roads, is (A) y = x3 /6 RL (B) y = x/6 RL (C) y = l²/6 RL (D) y = l3 /6 RL

Description : The standard equation of a cubic parabolic transition curve provided on roads, is (A) y = x3 /6 RL (B) y = x/6 RL (C) y = l²/6 RL (D) y = l3 /6 RL

Last Answer : Answer: Option A

The standard equation of a cubical spiral transition curve provided on roads, is (A) y = l²/6RL (B) y = x3 /6RL (C) y = x2 /6RL (D) y = x/6RL

Description : The standard equation of a cubical spiral transition curve provided on roads, is (A) y = l²/6RL (B) y = x3 /6RL (C) y = x2 /6RL (D) y = x/6RL

Last Answer : Answer: Option B

The type of curves generally provided on highways, is (A) Critical curve (B) Transition curve (C) Vertical curve (D) All the above

Description : The type of curves generally provided on highways, is (A) Critical curve (B) Transition curve (C) Vertical curve (D) All the above

Last Answer : Answer: Option D

The absolute minimum radius of horizontal curve for a design speed 60 kmph is (A) 131 m (B) 210 m (C) 360 m (D) None of these

Description : The absolute minimum radius of horizontal curve for a design speed 60 kmph is (A) 131 m (B) 210 m (C) 360 m (D) None of these

Last Answer : Answer: Option D

Curves in the same direction separated by short tangents, are called (A) Simple circular curves (B) Compound curves (C) Transition curves (D) Broken-back curves

Description : Curves in the same direction separated by short tangents, are called (A) Simple circular curves (B) Compound curves (C) Transition curves (D) Broken-back curves

Last Answer : Answer: Option D

Along a hill road, a side drain is provided on (A) Outer side of a spur curve(B) Outer side of a re-entrant curve (C) Outer side of both (a) and (b) (D) Inner side of both (a) and (b)

Description : Along a hill road, a side drain is provided on (A) Outer side of a spur curve (B) Outer side of a re-entrant curve (C) Outer side of both (a) and (b) (D) Inner side of both (a) and (b)

Last Answer : Answer: Option D

Over-turning of vehicles on a curve can be avoided by using (A) Compound curve (B) Vertical curve (C) Reverse curve (D) Transition curve

Description : Over-turning of vehicles on a curve can be avoided by using (A) Compound curve (B) Vertical curve (C) Reverse curve (D) Transition curve

Last Answer : (D) Transition curve

ferent grades are joined together by a (A) Compound curve (B) Transition curve (C) Reverse curve (D) Vertical curve

Description : ferent grades are joined together by a (A) Compound curve (B) Transition curve (C) Reverse curve (D) Vertical curve

Last Answer : (D) Vertical curve

If the radius of a simple curve is 600 m, the maximum length of the chord for calculating offsets, is taken (A) 15 m (B) 20 m (C) 25 m (D) 30 m

Description : If the radius of a simple curve is 600 m, the maximum length of the chord for calculating offsets, is  taken  (A) 15 m  (B) 20 m  (C) 25 m  (D) 30 m

Last Answer : (D) 30 m

If the long chord and tangent length of a circular curve of radius R are equal the angle of deflection, is (A) 30° (B) 60° (C) 90° (D) 120°

Description : If the long chord and tangent length of a circular curve of radius R are equal the angle of deflection, is (A) 30° (B) 60° (C) 90° (D) 120°

Last Answer : D

If is the speed of a locomotive in km per hour, g is the acceleration due to gravity, is the distance between running faces of the rails and is the radius of the circular curve, the required super elevation is (A) gV²/GR (B) Rg/GV² (C) GR/gV² (D) GV²/gR

Description : If is the speed of a locomotive in km per hour, g is the acceleration due to gravity, is the distance between running faces of the rails and is the radius of the circular curve, the required super elevation is (A) gV²/GR (B) Rg/GV² (C) GR/gV² (D) GV²/gR

Last Answer : (D) GV²/gR

The tangent length of a simple circular curve of radius R (A) R tan (B) R tan (C) R sin (D) R sin

Description : The tangent length of a simple circular curve of radius R (A) R tan (B) R tan (C) R sin (D) R sin

Last Answer : Answer: Option B

A waveguide bend must have what minimum radius?

Description : A waveguide bend must have what minimum radius?

Last Answer : Greater than 2 wavelengths.

If L is the length of a moving vehicle and R is the radius of curve, the extra mechanical width b to be provided on horizontal curves, (A) L/R (B) L/2R (C) L²/2R (D) L/3R

Description : If L is the length of a moving vehicle and R is the radius of curve, the extra mechanical width b to be provided on horizontal curves, (A) L/R (B) L/2R (C) L²/2R (D) L/3R

Last Answer : Answer: Option C

While designing hair pin bends on highways, the minimum (A) Designed speed is 20 km/hour(B) Gradient is 1 in 40 (C) Gradient is 1 in 200 (D) All the above

Description : While designing hair pin bends on highways, the minimum (A) Designed speed is 20 km/hour (B) Gradient is 1 in 40 (C) Gradient is 1 in 200 (D) All the above

Last Answer : Answer: Option D

The radius of a bar bend to form a hook, should not be less than (A) Twice the diameter (B) Thrice the diameter (C) Four times the diameter (D) Five times the diameter

Description : The radius of a bar bend to form a hook, should not be less than (A) Twice the diameter (B) Thrice the diameter (C) Four times the diameter (D) Five times the diameter

Last Answer : Answer: Option A

The minimum width of the pavement of a National Highway should be (A) 4.7 m (B) 5.7 m (C) 6.7 m (D) 7.7 m

Description : The minimum width of the pavement of a National Highway should be (A) 4.7 m (B) 5.7 m (C) 6.7 m (D) 7.7 m

Last Answer : Answer: Option B

The minimum number of main steel bars provided in R.C.C. (A) Rectangular columns is 4 (B) Circular columns is 6 (C) Octagonal columns is 8 (D) All the above

Description : The minimum number of main steel bars provided in R.C.C. (A) Rectangular columns is 4 (B) Circular columns is 6 (C) Octagonal columns is 8 (D) All the above

Last Answer : Answer: Option D

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

no super elevation is provided on a road along curves, pot holes may develop at (A) Inner edge of the road (B) Outer edge of the road (C) Centre of the road (D) Nowhere on the road

Description : no super elevation is provided on a road along curves, pot holes may develop at (A) Inner edge of the road (B) Outer edge of the road (C) Centre of the road (D) Nowhere on the road

Last Answer : Answer: Option B

If the radius of a simple curve is R, the length of the chord for calculating offsets by the method of chords produced, should not exceed. (A) R/10 (B) R/15 (C) R/20 (D) R/25

Description : If the radius of a simple curve is R, the length of the chord for calculating offsets by the method of  chords produced, should not exceed.  (A) R/10  (B) R/15  (C) R/20  (D) R/25 

Last Answer : (C) R/20 

A portion of an embankment having a uniform up-gradient 1 in 500 is circular with radius 1000 m of the centre line. It subtends 180° at the centre. If the height of the bank is 1 m at the lower end, and side slopes 2:1, the earth work involved. (A) 26,000 m3 (B) 26,500 m3 (C) 27,000 m3 (D) 27,500 m

Description : A portion of an embankment having a uniform up-gradient 1 in 500 is circular with radius 1000 m of the centre line. It subtends 180° at the centre. If the height of the bank is 1 m at the lower end, and side slopes 2 ... earth work involved. (A) 26,000 m3 (B) 26,500 m3 (C) 27,000 m3 (D) 27,500 m

Last Answer : (D) 27,500 m3

The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, is (A) One-half of the radius (B) One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Last Answer : (C) One-quarter of the radius

For a curve of radius 100 m and normal chord 10 m, the Rankine's deflection angle, is (A) 0°25'.95 (B) 0°35'.95 (C) 1°25'.53 (D) 2°51'.53

Description : For a curve of radius 100 m and normal chord 10 m, the Rankine's deflection angle, is (A) 0°25'.95 (B) 0°35'.95 (C) 1°25'.53 (D) 2°51'.53

Last Answer : (D) 2°51'.53

Extra widening required at a horizontal curve on a single lane hill road of radius 80 m for a design speed of 50 km ph and for a vehicle with wheel base 6.0 m is (A) 0.225 m (B) 0.589 m (C) 1.250 m (D) None of these

Description : Extra widening required at a horizontal curve on a single lane hill road of radius 80 m for a design speed of 50 km ph and for a vehicle with wheel base 6.0 m is (A) 0.225 m (B) 0.589 m (C) 1.250 m (D) None of these

Last Answer : Answer: Option B

The total value of extra widening required at a horizontal curve on a two lane hill road of radius 42 m for a design speed of 50 kmph and for vehicles with wheel base 6 m, is (A) 0.500 m (B) 0.589 m (C) 1.089 m (D) 0.089 m

Description : The total value of extra widening required at a horizontal curve on a two lane hill road of radius 42 m for a design speed of 50 kmph and for vehicles with wheel base 6 m, is (A) 0.500 m (B) 0.589 m (C) 1.089 m (D) 0.089 m

Last Answer : Answer: Option C

If degree of a road curve is defined by assuming the standard length of an arc as 30 metres, the radius of 1° curve is equal (A) 1719 m (B) 1146 m (C) 1046 m (D) 1619 m

Description : If degree of a road curve is defined by assuming the standard length of an arc as 30 metres, the radius of 1° curve is equal (A) 1719 m (B) 1146 m (C) 1046 m (D) 1619 m

Last Answer : Answer: Option A

If x% is the gradient of an alignment and y% is the gradient after proper super-elevation along a curved portion of a highway, the differential grade along the curve, is (A) (x + y) % (B) (x - y) % (C) (y - x) % (D) (y + x) %

Description : If x% is the gradient of an alignment and y% is the gradient after proper super-elevation along a curved portion of a highway, the differential grade along the curve, is (A) (x + y) % (B) (x - y) % (C) (y - x) % (D) (y + x) %

Last Answer : Answer: Option C

Which of the following is incorrect? a. In a solid shaft maximum shear stress occurs at radius = radius of shaft b. In a solid shaft maximum shear stress occurs at center c. In a hollow shaft maximum shear stress occurs at outer radius d. In a hollow shaft minimum shear stress occurs at inner radius

Description : Which of the following is incorrect? a. In a solid shaft maximum shear stress occurs at radius = radius of shaft b. In a solid shaft maximum shear stress occurs at center c. In a hollow ... maximum shear stress occurs at outer radius d. In a hollow shaft minimum shear stress occurs at inner radius

Last Answer : b. In a solid shaft maximum shear stress occurs at center