Description : While designing hair pin bends on highways, the minimum (A) Designed speed is 20 km/hour (B) Gradient is 1 in 40 (C) Gradient is 1 in 200 (D) All the above
Last Answer : Answer: Option D
Description : The minimum design speed for hairpin bends in hill roads is taken as (A) 20 kmph (B) 30 kmph (C) 40 kmph (D) 50 kmph
Last Answer : Answer: Option A
Description : In case of a hair pin bend of a highway, (A) Minimum radius of inner curve is 14 m (B) Minimum radius of transition is 15 m (C) Circular compound curve may be provided (D) All the above
Description : Minimum radius of curvature of National Highways or State highways in hill region free from snow, is kept (A) 60 m (B) 50 m (C) 33 m (D) 30 m
Last Answer : Answer: Option B
Description : From the point of tangency before an intersection, the route markers are fixed at a distance of (A) 15 m to 30 m (B) 20 m to 35 m (C) 40 m to 50 m (D) 100 m to 150
Description : the loss due to friction in pipes is 4 m, the total losses in strainer and bends may be taken as (A) 0.10 m (B) 0.20 m (C) 0.5 m (D) 1.0 m
Description : In order to avoid the material failure in a braced column, the clear distance between restraints should never exceed [ A ] 30 times the minimum dimensions of the column [ B ] 40 times the minimum ... 50 times the minimum dimensions of the column [ D ] 60 times the minimum dimensions of the column
Last Answer : [ D ] 60 times the minimum dimensions of the column
Description : Pick up the incorrect statement from the following regarding fire hydrants (A) Fire hydrants are fitted in water mains at 100 m to 150 m apart at fire (B) The minimum water pressure hydrants, is kept 1.5 kg/ ... to 1.5 kg/cm2 is made available for 4 to 5 hours for constant use (D) None of these
Last Answer : (D) None of these
Description : A tree breaks due to storm and the broken part bends so that the top of the tree touches the ground making an angle 30° with it. The distance between the foot of the tree to the point where the top touches the ground is 8 m. Find the height of the tree. -Maths 9th
Last Answer : The broken part bends so that the top of the tree touches the ground making an angle 30 °. The distance between the foot of the tree to the point where the top touches the ground is 8 m. Original height of ... After rationalising Now we have , A`BC = AB + BC Take LCM So , original height of tree is
Description : If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60 mm, the particular aggregate will be flaky if its minimum dimension is less than (A) 20.5 mm (B) 30.5 mm (C) 40.5 mm (D) 50.5 mm
Last Answer : Answer: Option C
Description : If a 30 m chain diverges through a perpendicular distance d from its correct alignment, the error in length, is (A) (d²/60) m (B) (d²/30) m (C) (d²/40) m (D) (d/30) m
Last Answer : (A) (d²/60) m
Description : In grillage foundations, distance between flanges of grillage beams, is kept (A) 40 cm (B) Equal to flange width (C) Twice the flange width (D) Maximum of (a), (b) and (c)
Description : The strength of brick masonry in 1:6 cement mortar, is (A) 20 tonnes/m2 (B) 40 tonnes/m2 (C) 50 tonnes/m2 (D) 60 tonnes/m
Description : In case of Raymond pile (A) Lengths vary from 6 m to 12 m (B) Diameter of top of piles varies from 40 cm to 60 cm (C) Diameter of pile at bottom varies from 20 cm to 28 cm (D) All the above
Description : If h is the loss due to friction in a pipe. Total losses in strainer and bends may be taken as (A) 0.01 h (B) 0.45 h (C) 0.20 h (D) 0.25 h
Description : Minimum stopping distance for moving vehicles on road with a design speed of 80 km/hour, is (A) 80 m (B) 100 m (C) 120 m (D) 150 m
Description : Maximum distance between expansion joints in structures as per IS: 456 1978 is (A) 20 m (B) 30 m (C) 45 m (D) 60 m
Last Answer : (C) 45
Description : The factor to be considered for the source of city water supply, is (A) Quantity and quality of the available water (B) Elevation of the source of water (C) General terrain intervening the area (D) All the above
Last Answer : (D) All the above
Description : A well penetrates to 30 m below the static water table. After 24 hours of pumping at 31.40 litres/minute, the water level in a test well at a distance of 80 m is lowered by 0.5 m and in a well 20 m away water is ... 1.185 m2 /minute (B) 1.285 m2 /minute (C) 1.385 m2 /minute (D) 1.485 m2 /minute
Description : Inter-distance between ventilation columns in a sewer line is kept A. 25 to 50 m B. 50 m to 100 m C. 100 m to 150 m D. 150 m to 300 m
Last Answer : ANS: D
Description : The width of the right of way in urban area, is kept between 24 m to 60 m for (A) National Highways (B) State Highways (C) Both (a) and (b) (D) None of these
Description : Depth of borings for soil investigation, is generally kept below low water level (A) 30 m (B) 35 m (C) 45 m (D) 40 m
Last Answer : (C) 45 m
Description : According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 20 cm (B) 30 cm (C) 40 cm (D) 75 cm
Description : A well is sunk in an unconfined aquifer having a saturated depth of 100 m. Assuming the equilibrium flow conditions and a homogeneous aquifer and radius of influence to be same, the ratio of discharges at 20 m and 40 m draw downs, is (A) 2/3 (B) 5/4 (C) 4/5 (D) 8/7
Description : A glass prism has a refracting angle of `60^@`. The angle of minimum deviation is `40^@`. If velocity of light in vacuum is `3 xx 10^8 m//s`. Calculat
Last Answer : A glass prism has a refracting angle of `60^@`. The angle of minimum deviation is `40^@`. If ... of light in glass. What is the angle of incidence ?
Description : When examining a completed bend test, the angle of the bend was found to be 185°. The testing specification calls for the sample to have been formed through 180°? a) They should be acceptable as ... then re-examined d) They should be rejected as the angle is not close enough to be acceptable
Last Answer : c) New bends should be produced and bent to 180° then re-examined
Description : Minimum required water cement ratio for a workable concrete, is (A) 0.30 (B) 0.40 (C) 0.50 (D) 0.60
Description : The Minimum pitch of the helical reinforcement in circular columns should be [ A ] 25 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm
Last Answer : [ A ] 25 mm
Description : For Unbraced column, the ratio of the clear height of the column to the minimum dimension of the column shall not exceed [ A ] 30 [ B ] 40 [ C ] 50 [ D ] 60
Last Answer : [ A ] 30
Description : The L.C.M of two numbers is 14 times their H.C.F . The sum of the L.C.M. and the H.C.F . is 600. If one number is 280 , then the other number is (a) 40 (b) 60 (c) 80 (d) 100
Last Answer : 80
Description : The radius of curvature of the arc of the bubble tube is generally kept (A) 10 m (B) 25 m (C) 50 m (D) 100 m
Last Answer : (D) 100 m
Description : Height of crucible is kept from top surface of mould? (i) 30 mm (ii) 40 mm (iii) 50 mm* (iv) 60 mm
Last Answer : (iii) 50 mm*
Description : A simple pendulum consisting of a mass M attached to a string of length L is released from rest at an angle `alpha`. A pin is located at a distance l
Last Answer : A simple pendulum consisting of a mass M attached to a string of length L is released from rest at an angle `alpha` ... ^(-1) [(L cos alpha-l)/(L+l)]`
Description : A nuisance is experienced in diluting water if dilution factor is less than A. 100 B. 60 C. 40 D. 20
Description : Which of the following statements regarding cash flow patterns (for time periods 0, 1, 2, 3, and 4) is correct? A. The sequence of -Rs.100, Rs.50, Rs.40, Rs.60, and Rs.50 is a non-conventional cash ... -Rs.50, Rs.50, Rs.70, Rs.60, and -Rs.150 potentially has at most two internal rates of return.
Last Answer : B. The sequence of -Rs.100, Rs.600, -Rs.1,100, Rs.600, and Rs.20 potentially has a maximum of two internal rates of return.
Description : If a secondary coil has 40 turns, and, a primary coil with 20 turns is charged with 50 V of potential difference, then the potential difference in the secondary coil would be A. 50 V in secondary coil B. 25 V in secondary coil C. 60 V in secondary coil D. 100 V in secondary coil
Last Answer : 100 V in secondary coil
Description : The size of a single plant cell is usually within the range of A.10-20μm in diameter and 25-100μm long B.20-40μm in diameter and 100-200μm long C.40-60μm in diameter and 200-300μm long D.60-80μm in diameter and 300-400μm long
Last Answer : B.20-40μm in diameter and 100-200μm long
Description : Standard disc Plough consists of steel disc of _ diameter a) 20 to 40 cm. c) 60 to 90 cm b) 30 to 60 cm. d) 70 to 100 cm
Last Answer : 60 to 90 cm
Description : Transmission voltage of ll kV is normally used for distances upto (a) 20—25 km (b) 40—50 km (c) 60—70 km (d) 80—100 km
Last Answer : (a) 20—25 km
Description : If the degree of saturation of a partially saturated soil is 60%, then air content of the soil is (A) 40 % (B) 60 % (C) 80 % (D) 100 %
Last Answer : (A) 40 %
Description : An intense rain is falling at a uniform rate of 7.5 cm/hour for a period of 60 minutes on a basin whose area is 500 hectares. If the average infiltration capacity during the entire rain period is assumed to be 1.5 ... of the basin, is (A) 40 cumecs (B) 60 cumecs (C) 80 cumecs (D) 100 cumecs
Description : Which of the following represents hardest grade of bitumen? (A) 30/40 (B) 60/70 (C) 80/100 (D) 100/120
Description : The normal road width of National and State highways (A) Is kept 45 m (B) In plain and rolling terrain built-up area, is 30 m (C) In mountainous built-up area is 20 m (D) All the above
Description : A gun fires shell with a muzzle velocity of 600 m/sec. The angle of inclination of the gun so that the shell hits a target at a distance of 32 km at level 100 m higher than the gun would be approximately? a.60? b.45? c.30? d.15? e.Either of (A) and (C)
Last Answer : e. Either of (A) and (C)
Description : For transmission of power over a distance of 500 km, the transmission voltage should be in the range (a) 150 to 220 kV (b) 100 to 120 kV (c) 60 to 100 kV (d) 20 to 50 kV
Last Answer : (a) 150 to 220 kV
Description : Calculate the value of critical damping coefficient if a vibrating system has mass of 4kg and stiffness of 100N/m A 20 N-sec/m B 40 N-sec/m C 60 N-sec/m D 80 N-sec/m
Last Answer : B 40 N-sec/m
Description : Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface ... C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50
Last Answer : (C) 70
Description : Ravi walks to and fro to a Gym. He spends 30 minutes in gym. If he walks at speed of 20 km an hour, he returns to home at 8.00 a.m. If he walks at 30 km an hour, he returns to home at 7.30 a.m. How fast must he walk in order to return at 7.15 hours? a) 40 km/hr b) 30 km/hr c) 60 km/hr d) 50 km/hr
Last Answer : A As per the question, let D be the total distance and ‘t’ is the time taken. So we have: D=20t 20t =30(t-0.5) 20t=30t-15 10t=15 t=3/2 D= 30 km Now, for the condition given we have: 30=S(t-3/4) 30=S(3/2-3/4) 30=S((6-3)/4) 30=S(3/4) S=40 km/hr
Description : Calculate the power of a material with electric field 100 units at a distance of 10cm with a current of 2A flowing through it. a) 10 b) 20 c) 40 d) 80
Last Answer : b) 20